Epson Projector BrightLink 585Wi User Manual

							3. To move the main toolbar to the other side of the screen, tap the arrow on the opposite side of
the screen.
Note: You can use the pen or your finger (BrightLink 595Wi) to move the arrow icon up or down to
reposition the toolbar.
4. To switch to one of the other interactive modes, do one of the following: • To switch to whiteboard mode, select the Whiteboard tool.
• To switch to PC Interactive mode, select , then select .
Note: You can also press the Pen Modebutton on the remote control to switch between modes.
5. To close the main toolbar, select the icon at the bottom of the toolbar. Note: If you want to hide the toolbar automatically after drawing, select the icon at the bottom of
the toolbar.
6. To show or hide the projection control toolbar, select the arrow.
Parent topic: Interactive Modes
Controlling Computer Features from a Projected Screen (PC Interactive Mode) You can navigate, select, and interact with your computer programs from the projected screen using the
interactive pens or your finger (BrightLink 595Wi) just as you would a mouse.
Note:OS X users need to install the Easy Interactive Driver before using PC Interactive mode. Go to
epson.com/support (U.S.) orepson.ca/support (Canada) and select your projector.
1. Connect the projector to your computer using a USB cable.
2. Turn on your projector and project your computer screen.
121     
						

							3. Press the
Menubutton on the remote control, select the Extendedmenu, and press the Enter
button.
4. Select the USB Type Bsetting and press the Enterbutton.
5. Select one of the following: •Easy Interactive Function to use PC Interactive mode.
• USB Display/Easy Interactive Function to use PC Interactive mode and USB Display.
122 
						

							6. Select the
Easy Interactive Function setting and press theEnterbutton.
7. Select one of the following as the Pen Operation Modedepending on the operating system your
computer is using:
• Mode 1: Windows XP or earlier
• Mode 2: Windows Vista, Windows 7, Windows 8, and OS X
• Mode 3: Linux
8. Press the Enterbutton on the remote control, then press the Menubutton to exit the Extended
menu.
9. Hover near or tap on the board or the projected image with the interactive pen or your finger (BrightLink 595Wi).
The icon is displayed on the projected screen.
10. Select the icon, then select the icon. You can now operate the computer using the interactive pens or your finger (BrightLink 595Wi).
PC Interactive Mode System Requirements
Parent topic: Interactive Modes
123    
						

							PC Interactive Mode System Requirements
Your computer system must meet the system requirements here to use PC Interactive mode and Easy
Interactive Tools.
Note:Easy Interactive Driver must be installed and running to use Easy Interactive Tools on a Mac.
Requirement Windows Mac
Operating system Windows XP Professional, Home OS X 10.5.x, 10.6.x, 10.7.x, 10.8.x, Edition, and Tablet PC Edition (32-bit); 10.9.x
except for Service Pack 1
Windows Vista Ultimate, Enterprise,
Business, Home Premium, and Home
Basic (32-bit)
Windows 8.x Pro, Enterprise, Windows 7
Ultimate, Enterprise, Professional, Home
Premium, and Home Basic (32- and 64-
bit)
CPU Intel Pentium M 1.6 GHz or faster (Core2 Power PC G4 1.5 GHz or faster
Duo 1.2 GHz or faster recommended) (Core Duo 1.5 GHz or faster
recommended)
Memory 512MB or more (1G or more recommended)
Hard disk space 100MB or more
Display Resolution between 1024 × 768 and 1920 × 1080, 16-bit color or greater
Parent topic: Controlling Computer Features from a Projected Screen (PC Interactive Mode)
Using the Interactive Pens Follow the instructions in these sections to use the interactive pens.
Using the Pens
Pen Calibration
Parent topic:Using the Interactive Features
124 
						

							Using the Pens
Your projector came with a blue pen and an orange pen, identified by the color on the end of the pen.
You can use either pen, or both pens at the same time (one of each color), with Easy Interactive Tools.
Make sure the pen batteries are installed.
Note:The pen turns off automatically after 20 minutes of inactivity. Tap the pen tip or press the button on
the side to turn the pen back on.
1 Pen tip
2 Battery light
3 Power/function button
4 Attachment for optional strap or cord
5 Battery cover
• To turn on the pen, tap the pen tip or press the power/function button. Note: If you press the button, the battery light flashes briefly, then turns off. If the battery is low, the
battery light flashes continuously.
125  
						

							• For best performance, hold the pen perpendicular to the board, as shown below. Do not cover the
black section near the tip of the pen.
• To write or draw on the projection surface in annotation mode or whiteboard mode, do the following: • To select a projected item, such as an icon, tap the projection surface with the pen tip.
• To draw on the projected screen, tap the projection surface with the pen and drag it as necessary.
• To move the pointer, hover over the surface without touching it.
• To switch the pen from drawing tool to eraser, press and hold the power/function button on the side.
126   
						

							• To use the pen as a mouse in PC Interactive mode, do the following:
• To left-click, tap the board with the pen tip.
• To double-click, tap twice.
• To right-click, press the power/function button on the side.
• To click and drag, tap and drag with the pen.
• To move the cursor, hover over the board without touching it.Note: If you do not want to use the hovering feature, you can turn it off using the Easy Interactive
Function in the projectors Extended menu.
Parent topic: Using the Interactive Pens
Related references
Projector Setup Settings - Extended Menu
Related tasks
Installing Batteries in the Pens
Pen Calibration Calibration coordinates the position of the pen with the location of your cursor. You only need to calibrate
the first time you use your projectors interactive features. Calibration results remain until you calibrate
again.
Be sure to calibrate the pen before performing finger touch calibration (BrightLink 595Wi).
If you notice positioning discrepancies after doing any of the following, calibrate again:
• Performing Keystone correction
• Adjusting the image size
127  
						

							• Using the Image Shift feature
• Moving the projector
Note:
Move any pen you are not using away from the projection screen while calibrating.
Calibrating Automatically
Calibrating Manually
Parent topic: Using the Interactive Pens
Calibrating Automatically You do not need the pens or a computer for Auto Calibration.
Note:You can start Auto Calibration by pressing the Userbutton on the remote control or by pressing
the Menu button on the remote control as described here.
1. Press the Menubutton, select the Extendedmenu, and press Enter.
128 
						

							2. Select the
Easy Interactive Function setting and pressEnter.
3. Select Auto Calibration and pressEnter.
4. Adjust the image focus, if necessary.
5. Press Enterto select Yes.
A pattern appears then disappears, and the system is calibrated. If you see a message that
calibration failed, you need to calibrate manually.
129 
						

							The cursor location and pen position should match after calibration. If not, you may need to calibrate
manually.
Parent topic:
Pen Calibration
Related tasks
Calibrating Manually
Focusing the Image
Calibrating Manually If the cursor location and pen position do not match after auto calibration, you can calibrate manually.
1. Press theMenubutton, select the Extendedmenu, and press Enter.
130