Epson Projector BrightLink 585Wi User Manual

							2. Select the
Easy Interactive Function setting and pressEnter.
3. Select Manual Calibration and pressEnter.
4. Adjust the image focus, if necessary.
5. Press Enterto select Yes.
A flashing green circle appears in the upper left corner of your projected image.
6. Touch the center of the circle with the tip of the pen.
131 
						

							The circle disappears, and you see another circle below the first one.
132  
						

							Note:
For the most accurate calibration, make sure you touch the center of the circle.
7. Touch the center of the next circle, then repeat. When you get to the bottom of the column, the next circle appears at the top of a new column.
Note: Make sure you are not blocking the signal between the pen and the interactive receiver (next
to the projection window on the projector).
If you make a mistake, press the Escbutton on the remote control to go back to the previous circle.
To restart the calibration process, press and hold the Escbutton for 2 seconds.
8. Continue until all of the circles disappear.
Parent topic: Pen Calibration
133   
						

							Related tasks
Focusing the Image
Calibrating Automatically
Using Finger Touch Interactivity You can use your finger to perform the same functions as the interactive pens when you install the
Touch Unit (BrightLink 595Wi).
Note:See the Installation Guide for detailed instructions on installing the Touch Unit and calibrating for
finger touch interactivity.
Touch Unit Safety Instructions
Calibrating for Finger Touch Interactivity
Using Finger Touch Operations
Parent topic: Using the Interactive Features
Touch Unit Safety Instructions The Touch Unit enables finger touch interactivity with your projector (BrightLink 595Wi). Do not connect
it to any other projectors or devices.
A built-in, high-power laser is emitted from the laser diffusion ports on the back of the Touch Unit.
134  
						

							Follow these precautions when using the Touch Unit and finger touch interactivity:
• Children using finger touch interactivity should always be accompanied by an adult.
• Never disassemble or modify the Touch Unit.
• Do not look into the laser diffusion ports on the back of the Touch Unit. The laser can damage your
eyes. Extra care should be taken when children are present.
• Do not allow the laser light from the Touch Unit to pass through or be reflected by any optical devices, such as a magnifying glass or mirror. This could cause personal injury or fire.
• Do not view the laser light from the Touch Unit using an optical device such as an eye loupe, magnifying glass, or microscope, especially within 2.75 inches (70 mm) of the laser diffusion ports.
This could damage your eyes.
• Unplug the projector from the electrical outlet and refer all repairs to qualified service personnel if any problems occur with the Touch Unit.
The Touch Unit is a Class 1 laser product that complies with IEC/EN60825-1:2007. The labels indicating
the Class 1 laser product and warnings are located in the following areas on the Touch Unit:
135    
						

							Parent topic:
Using Finger Touch Interactivity
Calibrating for Finger Touch Interactivity Finger touch calibration coordinates the positioning of your finger with the location of the cursor
(BrightLink 595Wi).
Note:Make sure you have calibrated the pens before calibrating for finger touch interactivity.
1. Press the Menubutton, select the Extendedmenu, and press Enter.
136 
						

							2. Select the
Easy Interactive Function setting and pressEnter.
3. Select Touch Unit Setup and pressEnter.
137 
						

							4. Select
Touch Calibration and pressEnter.
The following screen appears:
5. Adjust the image focus, if necessary.
6. Press Enterto select Yes.
A flashing green circle appears in the upper left corner of your projected image.
138 
						

							7. Touch and hold the center of the circle with your finger until the circle disappears and another circle
appears, then release it.
The circle disappears, and you see another circle below the first one.
Note: For the most accurate calibration, make sure you touch the center of the circle with the tip of
your finger.
Note: Make sure you are not blocking the signal between your finger and the interactive receiver
(next to the projection window on the projector).
8. Touch the center of the next circle with your finger and continue until all of the circles disappear.
139   
						

							When you get to the bottom of a column, the next circle appears at the top of a new column.
Note:
If you make a mistake, press the Escbutton on the remote control to go back to the previous
circle. To restart the calibration process, press and hold the Escbutton for 2 seconds.
9. If the cursor location and your finger position do not match, repeat these steps to calibrate again.
Parent topic: Using Finger Touch Interactivity
Related tasks
Focusing the Image
Calibrating Automatically
Calibrating Manually
Using Finger Touch Operations You can use your finger to interact with the projected screen, just as you would use an interactive pen
(BrightLink 595Wi). You can use either a pen or your finger, or use both at the same time.
When performing touch operations with your finger, you can use two fingers in annotation and
whiteboard modes.
1. Install the Touch Unit as described in the Installation Guide.
2. Calibrate the pens.
3. Adjust the angle of the Touch Unit as described in the Installation Guide.
140