Epson Aculaser M 2000 Service Manual

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 241
Confidential
Rear Left Cover + Front Left Cover
1. Remove two Screws [2], and remove the Rear Left Cover [3].
2. Open the Front Door [1].
3. Remove two Screws [4], and remove the Front Left Cover [5].
C8
D8
[1] [2]
[3][4]
[5]
Exit Tray
1. Open the Upper Fusing Cover [2].
2. Remove two Claws [3], and remove the Upper Fusing Cover [2].
C9
D9
[2]
[3][3]
4039F2C019DA 

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 242
Confidential3. Remove two Screws [5], and remove the Exit Sensor Holder [6].
4. Remove three Screws [7], and remove the Exit Tray [8].
[5]
[6]
[7] [8]
Fusing Drive Assy
1. Remove three Screws [1] from rear side of the Main body and remove the Metal Blanking Plate [2].
C10
D10
[1]
[2]
[1] 

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 243
Confidential2. Remove three Screws [3] from the rear side of the Main body.
3. Release the hook section of the Spring from the groove to the rear side from upper part of 
Main Unit of the right rear side.
[3]
[4]
4. Remove the Fusing Drive Assy pushing upward [5] the connection part of the Transfer Belt 
from the right Door side. 
[5] 

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 244
Confidential
1st Image Transfer Pressure/Retraction Clutch (CL3)
1. Remove two Screws [1] from the Fusing Drive Assy and remove the Fusing Drive Motor 
[2].
2. Remove the E-ring [3].
D11
[3]
[2]
[1]
3. Remove two Screws [4], three E-rings [5] and remove Install Board [6].
[6]
[5]
[4] 

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 245
Confidential4. Remove the Gear [7] and then remove the Gear [8].
5. Remove the 1st Image Transfer Pressure/Retraction Clutch [10] with the Shaft [9].
[10]
[9]
[7]
[8] 

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 246
Confidential4.3.11  Group 11CONTENT
Parts/Units to be Disassembled
Guide
Hopper Drive AssyStandard Cassette Paper Feed Clutch (CL2)1st Image Transfer Pressure/Retraction Position Sensor 
(PC6)
ABC
Hopper Drive Assy
A
Standard cassette Paper Feed Clutch (CL2)
B
1st Image Transfer Pressure/
Retraction Position Sensor (PC6)
C 

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 247
ConfidentialDISASSEMBLY FLOWCHART
A7
B1
A1C1
B2
A2C2
B3
A3C3
B4
A4C4
B5
A5C5
B6
A6C6
B7
C7
Start
Right Rear Cover + Rear Cover
(P. 248)
Color Developing Motor (M3)
(P. 250)
Color PC Drum Motor (M2)
(P. 250)
Main Motor (M1)
(P. 251)
High Voltage Unit (HV1)
(P. 248)
Transfer Drive Assy
(P. 251)
Hopper Drive Assy
(P. 254)
Standard Cassette Paper Feed 
Clutch (CL2) 
(P. 256)
1st Image Transfer Pressure/...

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 248
Confidential
Right Rear Cover + Rear Cover
1. Open the Right Door [1].
2. Remove three Screws [2], and remove the Right Rear Cover [3].
3. Remove nine Screws [4], and remove the Rear Cover [5].
A1
B1
C1[1]
[3] [2] [4][4] [4]
[5]
High Voltage Unit (HV1)
1. Disconnect four Connectors [1].
2. Remove five Screws [2] and the Tab [3], and remove the High Voltage Unit [4].
A2
B2
C2
[1][2]
[3]
[4] 

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 249
Confidential
Make sure following things when installing the High Voltage Unit (HV1).†
Terminal end surely contacts (Refer to Figure 1).
†
Tab [5] surely set up (Refer to Figure 2).
Terminal end position
4038F2C087DA
 Figure 1 Figure 2
†
Be cautious not to install the wrong Screw because two types of Screws [2] are 
used.  • M Mark: Screws for installing metallic parts (Space between thread is small).
  • P...

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 250
Confidential
Color Developing Motor (M3)
1. Remove the Connector [1] and four Screws [2], and remove the Color Developing Motor 
[3].
A3
B3
C3[3]
[2]
[1]
4038F2C149DA
Color PC Drum Motor (M2)
1. Remove the Connector [1] and four Screws [2], and remove the Color PC Drum Motor [3].
A4
B4
C4[1][2] [3]
4038F2C150DA