Epson Aculaser M 2000 Service Manual

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 191
Confidential4. Reinstall the Stopper [7].
When reinstalling the Stopper, use care so that both ends of the Stopper will not open 
but stay parallel as shown in the figure above. 
Keep using the Stopper after once stretched out may cause uneven pitch or other 
image troubles.
Ó
·
[7]
4038F2C115DA
5. Reinstall the Gear [8].
6. Connect the Connector and the Flat Cable.
†
When reinstalling the Gear [8], make...

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 192
Confidential7. Install the Photoconductor Unit Guide Rail [9].
Make sure that the two Claws [10] at rear end of the rail are fit in the locating hole on 
the Main Unit.
8. Reinstall the Transfer Belt Unit.
9. Reinstall the Front Door.
10.Make skew adjustment of the PH Unit.


	


When installing the PH Unit, make sure to conduct PH Unit skew adjustment 
regardless of whether the Unit is new or...

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 193
Confidential4.3.4  Group 4CONTENT
DISASSEMBLY FLOWCHART
Parts/Units to be Disassembled
Guide
Rear Left Cover + Front Left CoverExit TrayUpper Cover + Control PanelDC Power Supply (PU1)
ABCD
Rear Left Cover
Upper Cover + 
Control Panel
C
Exit Tray
B Front Left Cover
A
A
DC Power Supply (PU1)
D
C1C2
D1D2
B1
A1
B2
C3
D3
B3
C4
D4D5
Rear Left Cover + Front Left Cover
(P. 194)
Right Rear Cover + Rear Cove
r
(P....

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 194
Confidential
Rear Left Cover + Front Left Cover
1. Remove two Screws [2], and remove the Rear Left Cover [3].
2. Open the Front Door [1].
3. Remove two Screws [4], and remove the Front Left Cover [5].
A1
B1
C1
D1
[1] [2]
[3][4]
[5]
Right Rear Cover + Rear Cover
1. Open the Right Door [1].
2. Remove three Screws [2], and remove the Right Rear Cover [3].
3. Remove nine Screws [4], and remove the Rear Cover...

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 195
Confidential
Exit Tray
1. Open the Upper Fusing Cover [2].
2. Remove two Claws [3], and remove the Upper Fusing Cover [2].
B3
C3
D3
[2]
[3] [3]
4039F2C019DA
3. Remove two Screws [5], and remove the Exit Sensor Holder [6].
4. Remove three Screws [7], and remove the Exit Tray [8].
[5]
[6]
[7] [8] 

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 196
Confidential
Upper Cover + Control Panel
1. Remove four Screws [1].
C4
D4
[1][1]
2. Remove the Ground terminal [2].
3. Remove the Connector [3], then remove the Upper Cover [4].
4. Remove five Screws [5], then remove the Control Panel [6].
Be careful when removing the Ground terminal because the edge of the Faston 
terminal is sharp. Make sure to work with gloves on to avoid getting injured. 
[2] [3]
[5]...

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 197
Confidential
DC Power Supply (PU1)
1. Remove nine Screws [1] and the Connector [2], then remove the protective sheet of the DC 
Power Supply [3]. 
D5
[2]
[1]
[1]
[3]
2. Remove all the Connectors on the DC Power Supply.
3. Remove eight Screws [4], and remove the DC Power Supply [5].
[5]
[4]
[4] 

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 198
Confidential4.3.5  Group 5CONTENT
Parts/Units to be Disassembled
Guide
Controller Board (PWB-P)Mechanical Control Board (PWB-M)RTC Board (PWB-R)
ABC
RTC Board (PWB-R)
C
B
Mechanical Control Board (PWB-M)
Controller Board (PWB-P)
A 

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 199
ConfidentialDISASSEMBLY FLOWCHART
B1
A1
C5  
C1
B2B3B4
A2C2
C3C4B5
Rear Left Cover + Front Left 
Cover
 (P. 200) Start
Controller Board (PWB-P)
(P. 200)
RTC Board (PWB-R)
(P. 205)
Mechanical Control Board (PWB-M)
(P. 203)Exit Tray(P. 201)
Controller Board Mounting Bracket
(P. 202) 

EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 200
Confidential
Rear Left Cover + Front Left Cover
1. Remove two Screws [2], and remove the Rear Left Cover [3].
2. Open the Front Door [1].
3. Remove two Screws [4], and remove the Front Left Cover [5].
A1
B1
C1
[1] [2]
[3][4]
[5]
Controller Board (PWB-P)
1. Remove six Screws [1].
A2
B2
C2