Epson Aculaser M 2000 Service Manual

SERVICE MANUAL
A3 Color Laser PrinterEPSON AcuLaser  C9200N
SEPG08001
Confidential 

Confidential
Notice:
The purpose of this manual is to provide the product knowledge and the technical information required for repair or maintenance of EPSON AcuLaser M2000D/M2000DN/
M2010D/M2010DN.†All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means electronic, mechanical, photocopying, or 
otherwise, without the prior written permission of SEIKO EPSON CORPORATION.
†This manual contains confidential information and...

Confidential
This manual consists of the following seven chapters:Various symbols are used throughout this manual either to provide additional 
information on a specific topic or to warn of possible danger present during a 
procedure or an action. Be sure to read and understand the information with these 
symbols.CHAPTER 1 PRODUCT DESCRIPTIONS
Describes the main features, basic specifications, consumable products, 
periodic replacement parts, and controller interface of the product.
CHAPTER 2 OPERATING...

Confidential
Safety-related SymbolsSafety Equipment†List of Safety Equipment
†Location of Safety Equipment†Safety System Wiring Schematic
Indicates an operating or maintenance procedure, practice or 
condition that, if not strictly observed, would result in injury or loss 
of life.Indicates an operating or maintenance procedure, practice or 
condition that, if not strictly observed, could result in injury or loss 
of life.Indicates an operating or maintenance procedure, practice or 
condition that, if...

Confidential
Laser Beam†Laser Opening Location†Handling Precautions
„Disassembling and adjustment procedures not specified herein 
may result in hazardous radiation exposure.
„Do not disassemble or attempt to adjust the PH unit for any 
reason whatsoever. When the PH unit malfunctions, replace it 
with a new one.
Laser Openings 

Confidential
Prohibited Matters†Never deactivate the safety equipment installed on the product for any reason 
whatsoever. 
†Never modify the safety equipment or replace it with part not approved by 
EPSON. Doing so may cause the safety functions to stop working properly, and 
may result in fire or injury.
†Never modify the product. If you are instructed to do so, however, fully 
understand the instruction and perform the modification.
To prevent an electric shock, burn, injury, etc., always turn the...

Confidential
Before performing repair and maintenance work, read and 
understand the documents of the product (e.g. service manual).  
Be sure to follow the specified steps and use the prescribed tools 
described in the documents.When disassembling or assembling the product, make sure to wear 
gloves to avoid injury from metal parts with sharp edges.Take care not to drop any screws, washers, or clips inside the 
printer body. Should it fall in, do not boot up your printer until the 
part has been safely...

Confidential
This manual is revised when the system, component, or part of the product is modified as a result of continuing improvements to the product’s performance and functions. 
 
See the table below for recent updates.
Revision HistoryRevision
Date of Issue
Description
A
July 25, 2008
First Release
B
October 14, 2008
Revision:†
Chapter 2„
2.2.2 Parts layout drawing
: revised the contents partially.
†
Chapter 3„
Table 3-17 Error Code List
: revised the contents partially.
„
Revised E555.
†
Chapter...

Confidential
Contents
Chapter 1PRODUCT DESCRIPTION1.1
  Product Specifications ........................................................................................  121.1.1
  Basic Specifications.................................................................................  12
1.1.2
  Paper Specifications ................................................................................  17
1.1.3
  Replacement Parts ......................................................................................

Confidential
4.2  List of Disassembly/Reassembly Parts/Units ...................................................  1604.3
  Main Unit Disassembly/Reassembly................................................................  1624.3.1
  Group 1 ..................................................................................................  162
4.3.2
  Group 2 ..................................................................................................  169
4.3.3
  Group 3...