Epson AcuLaser C4200DN User Manual

Cleaning and Transporting the Printer351
10
10
10
10
10
10
10
10
10
10
10
10
When relocating the printer, always choose a location that has 
adequate space for easy operation and maintenance. Use the 
following illustration as a guide for the amount of space required 
around the printer to ensure smooth operation. Dimensions 
shown in the illustrations below are in centimeters.
To install and use any of the following options, you will need the 
indicated amount of additional space.
The 550-sheet paper...

352Cleaning and Transporting the Printer
❏
Place the printer where you can easily unplug the power cord.
❏ Keep the entire computer and printer system away from 
potential sources of interference, such as loudspeakers or the 
base units of cordless telephones.
❏ Avoid using an electrical outlet that is controlled by wall 
switches or automatic timers. Accidental disruption of power 
can erase valuable information in your computer’s and 
printer’s memory.
c
Caution:
❏Leave adequate room around the...

Cleaning and Transporting the Printer353
10
10
10
10
10
10
10
10
10
10
10
10
❏Interface cables
❏ Loaded paper
❏ Photoconductor unit
❏ Installed options
2. Attach the protective materials onto the printer, then repack  the printer in its original box.
Checking color registration
New
 :vary
 according t
o c
olor p
roduct
 ( e
g. Piculet /
Puffin
 only)If you transported your printer for a long distance, you need to 
check the color registration for possible misalignment. For 
instructions, see Checking...

354Cleaning and Transporting the PrinterNote:
If the 1100-sheet paper cassette unit is installed, unlock the four feet 
at the bottom of the unit, then roll the printer to the new location. 
Make sure to lock the feet after relocating the printer.
2. Be sure to lift the printer by the correct positions as shown  below.
c
Caution:
When moving the printer, always keep it horizontal.
 

Troubleshooting355
11
11
11
11
11
11
11
11
11
11
11
11
Chapter 11 
Troubleshooting
Clearing Jammed Paper
New :quote
 the
 information f
rom
 the s
imilar
 product.If paper becomes jammed in the printer, the printer’s LCD panel 
and EPSON Status Monitor provide alert messages.
Precautions for clearing jammed paper
Be sure to observe the following points when you clear jammed 
paper.
❏ Do not remove jammed paper by force. Torn paper can be 
difficult to remove and might cause other paper jams. Pull it...

356Troubleshooting
w
Warning:
❏Be careful not to touch th e fuser, which is marked CAUTION 
HIGH TEMPERATURE , or the surrounding areas. If the 
printer has been in use, the fuser and the surrounding areas 
may be very hot.
❏ Do not insert your hand deep into the fuser unit as some 
components are sharp and may cause injury.
Paper Jam A B
New  :title
 i
s a
ccord
 as
 panel
 message
 (STM3 message)Follow the steps below to clear the jammed paper at cover A and 
B.
1. Press the latch on cover A and open...

Troubleshooting357
11
11
11
11
11
11
11
11
11
11
11
11
2. Push the inner green levers of the fuser unit down, and gently pull out any sheets of paper with both hands.
w
Warning:
Be careful not to touch th e fuser, which is marked CAUTION 
HIGH TEMPERATURE , or the surrounding areas. If the 
printer has been in use, the fuser and the surrounding areas 
may be very hot.
3. Open cover D.
 

358Troubleshooting
4. Grasp the handle of the photoconductor unit firmly and 
remove the unit from the printer.
w
Warning:
Be careful not to touch th e fuser, which is marked CAUTION 
HIGH TEMPERATURE , or the surrounding areas. If the 
printer has been in use, the fuser and the surrounding areas 
may be very hot.
 

Troubleshooting359
11
11
11
11
11
11
11
11
11
11
11
11
Note:
Make sure to place the photoconductor unit on the flat surface as 
shown below.
5. Gently pull out any sheets of paper with both hands.
 

360Troubleshooting
w
Warning:
Be careful not to touch the fuser, which is marked CAUTION 
HIGH TEMPERATURE , or the surrounding areas. If the 
printer has been in use, the fuser and the surrounding areas 
may be very hot.
c
Caution:
Do not touch the rollers inside the printer.
6. Reinstall the photoconductor unit, making sure the posts on  the sides of the unit slide into the slots.
w
Warning:
Be careful not to touch th e fuser, which is marked CAUTION 
HIGH TEMPERATURE , or the surrounding areas. If...