Epson AcuLaser C4200DN User Manual

Cleaning and Transporting the Printer341
10
10
10
10
10
10
10
10
10
10
10
10
6. Hold the transfer unit by the orange tabs and lower it into the printer, making sure that it fits into the guides. Push the 
transfer unit in and up until it clicks into place.
 

342Cleaning and Transporting the Printer
7. Pull the transfer unit toward you and push the orange tabs 
into place.
w
Warning:
Be careful not to touch th e fuser, which is marked CAUTION 
HIGH TEMPERATURE , or the surrounding areas. If the 
printer has been in use, the fuser and the surrounding areas 
may be very hot.
 

Cleaning and Transporting the Printer343
10
10
10
10
10
10
10
10
10
10
10
10
8. Close cover A.
9. Turn on the printer.
Cleaning the photoconductor unit
If printouts have dots at every 30 mm, wipe a roller in the 
photoconductor unit with a dry soft cloth or cotton swab. 
Follow the steps below to clean the photoconductor unit.
c
Caution:
Do not take too much time to clean the photoconductor. Exposing 
the photoconductor to too much light may damage the printer.
1. Turn off the printer.
 

344Cleaning and Transporting the Printer
2. Press the latch on cover A and open the cover.
3. Raise cover D.
 

Cleaning and Transporting the Printer345
10
10
10
10
10
10
10
10
10
10
10
10
4. Hold the photoconductor unit by the handle, and slowly lift it straight out of the printer.
w
Warning:
Be careful not to touch th e fuser, which is marked CAUTION 
HIGH TEMPERATURE , or the surrounding areas. If the 
printer has been in use, the fuser and the surrounding areas 
may be very hot.
 

346Cleaning and Transporting the Printer
5. Place the printout that has dots on it and the photoconductor 
unit on a flat table as shown below.
Note:
❏Make sure to align the center of the printout and center of the 
photoconductor unit when positioning them.
❏ Place the printout faceup so the  short edge that comes out of the 
printer first is against the photoconductor unit as shown in the 
diagram.
 

Cleaning and Transporting the Printer347
10
10
10
10
10
10
10
10
10
10
10
10
6. Look for the roller that is the same color as the dots on the printout. Then, look for the place on the roller that is vertically 
in the same position as the dots on the printout.
a. Yellow
b. Magenta
c. Cyan
d. Black
Note:
The illustration indicates that the dots on the printout are magenta 
as an example.
a
b
cd
 

348Cleaning and Transporting the Printer
7. Turn the gray part of the black roller to find the spot.
c
Caution:
Be careful not to scratch the su
rface of the drum and rollers. 
Also, avoid touching the drum an d rollers, since oil from your 
skin may permanently damage their surface and affect print 
quality.
8. Wipe the spot off the black roller with a dry soft cloth or cotton  swab.
 

Cleaning and Transporting the Printer349
10
10
10
10
10
10
10
10
10
10
10
10
c
Caution:
❏Be careful not to scratch th e surface of the drum (green 
roller) and rollers (black rollers). Also, avoid scratching 
the drum and rollers, since oil from your skin may 
permanently damage their surface and affect print 
quality.
❏ Do not expose the photoconductor unit and the developer 
cartridge to light any longer than necessary.
❏ Do not store the photoconductor unit in an area subject 
to direct sunlight.
9....

350Cleaning and Transporting the Printer
w
Warning:
Be careful not to touch the fuser, which is marked CAUTION 
HIGH TEMPERATURE , or the surrounding areas. If the 
printer has been in use, the fuser and the surrounding areas 
may be very hot.
10. Close covers D and A.
11. Turn on the printer.
Transporting the Printer
Ne w :F or
 l
arge-size
 product/ q
uote
 t
he
 information
 from
 the
 similar
 product
 a
nd
 confirm
 the
 specification f
or
 optional
 paper
 cassette
Finding a place for the printer...