Home > Epson > Printer > Epson AcuLaser C3800N User Manual

Epson AcuLaser C3800N User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson AcuLaser C3800N User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Using the Control Panel181
    EPSON AcuLaser C3800 Users Guide
    *5When the Get IPAddress setting is changed from Panel or PING to Auto, the panel setting values are 
    saved. When Auto is changed to Panel or PING, the saved setting values are displayed. 192.168.192.168 
    if the settings are not made from the panel.
    USB I/F
    Allows you to activate or deactivate the USB interface.
    USB SPEED
    Allows you to select the operation mode of USB interface. Selecting HS is recommended. 
    Select FS if HS does not work on your computer system. 
    Buffer Size
    Determines the amount of memory to be used for receiving data and printing data. If 
    Maximum is selected, more memory is allocated for receiving data. If set to Minimum is 
    selected, more memory is allocated for printing data.
    Note:
    ❏To activate Buffer Size settings, you must turn off the printer for more than five seconds then 
    turn it back on. Or, you can perform a Reset All operation, as explained in Reset Menu on 
    page 179. 
    ❏Resetting the printer erases all print jobs. Make sure the Ready light is not flashing when you 
    reset the printer.
    Network Menu
    See the Network Guide for each setting.
    AUX Menu
    See the Network Guide for each setting.
    USB Host Menu
    This menu allows you to use the USB Host printing function. For instructions on using the 
    function, see Printing Directly from a USB Memory on page 206.
    Item Settings (default in bold)
    USB Host
    *1On, Off
    Device Detection
    *2Manual, Auto
     
    						
    							Using the Control Panel182
    EPSON AcuLaser C3800 Users Guide
    *1After this item is changed, the setting value takes effect after a warm boot or after the power is turned on 
    again. While it is reflected in the Status Sheet and EJL read-back, the actual change takes effect after a 
    warm boot or after the power is turned on again.
    *2Available only when USB Host is set to ON.
    USB Host
    Enables you to print directly from a USB memory via a USB Host interface.
    Device Detection
    Specifies whether or not to detect the device inserted in the USB Host interface every time. 
    If you select Auto, the device is detected every time just after the device is inserted. If you 
    select Manual, the device may not be detected when the printer is in the sleep mode.
    PCL Menu
    These settings are available in the PCL mode.
    *1Available only when downloaded fonts are available.
    *2Available only when the optional font ROM module is installed.
    *3Depending on the font that has been selected.
    *4Depending on whether Letter (60) or A4 (64) paper has been selected. Item Settings (default in bold)
    FontSourceResident, Download
    *1, ROM A*2
    Font Number0… 65535 (depending on your settings)
    Pitch
    *30.44 … 10.00 … 99.99 cpi in 0.01 cpi increment
    Height
    *34.00 … 12.00 … 999.75 pt in 0.25 pt increment
    SymSetIBM-US, Roman-8, Roman-9, ECM94-1, 8859-2 ISO, 8859-9 ISO, 8859-10ISO, 
    8859-15ISO, PcBlt775, IBM-DN, PcMultiling, PcE.Europe, PcTk437, PcEur858, 
    Pc1004, WiAnsi, WiE.Europe, WiTurkish, WiBALT, DeskTop, PsText, VeInternati, 
    VeUS, MsPublishin, Math-8, PsMath, VeMath, PiFont, Legal, UK, ANSI ASCII, 
    Swedis2, Italian, Spanish, German, Norweg1, French2, Windows, McText, 
    Hebrew7, 8859-8 ISO, Hebrew8, Arabic8, OCR A, OCR B Pc866Cyr, Pc866Ukr, 
    WinCyr, ISOCyr, Pc8Grk, Pc851Grk, WinGrk, ISOGrk, Greek8, Pc862Heb, 
    Pc864Ara, HPWARA
    Form 5 … 60/64
    *4 … 128 lines
    CR FunctionCR, CR+LF
    LF FunctionLF, CR+LF
    Tray Assign4K, 5S, 4
     
    						
    							Using the Control Panel183
    EPSON AcuLaser C3800 Users Guide
    FontSource
    Sets the default font source.
    Font Number
    Sets the default font number for the default font source. The available number depends on 
    the settings you made.
    Pitch
    Specifies the default font pitch if the font is scalable and of fixed-pitch. You can select from 
    0.44 to 99.99 cpi (characters per inch), in 0.01-cpi increments. This item may not appear 
    depending on the Font Source or Font Number settings.
    Height
    Specifies the default font height if the font is scalable and proportional. You can select from 
    4.00 to 999.75 points, in 0.25-point increments. This item may not appear depending on 
    the Font Source or Font Number settings.
    SymSet
    Selects the default symbol set. If the font you selected in Font Source and Font Number is 
    not available in the new SymSet setting, the Font Source and the Font Number settings are 
    automatically replaced with the default value, IBM-US.
    Form
    Selects the number of lines for the selected paper size and orientation. This also causes a 
    line spacing (VMI) change, and the new VMI value is stored in the printer. This means that 
    later changes in the Page Size or Orientation settings cause changes in the Form value, 
    based on the stored VMI.
    CR Function, LF Function
    These functions are included for users of particular operating systems, such as UNIX.
    Tray Assign
    Changes the assignment for the paper source select command. When 4 is selected, the 
    commands are set as compatible with the HP LaserJet 4. When 4K is selected, the 
    commands are set as compatible with the HP LaserJet 4000, 5000, and 8000. When 5S is 
    selected, the commands are set as compatible with the HP LaserJet 5S.
     
    						
    							Using the Control Panel184
    EPSON AcuLaser C3800 Users Guide
    PS3 Menu
    This menu allows you to make settings which affect the printer when it is in the PS3 mode.
    *Available only when connected via Network interface.
    Error Sheet
    When you select On, the printer prints out an error sheet when an error occurs in the PS3 
    mode or when the PDF file you tried to print is not a supported version.
    Coloration
    Allows you to select the color printing or black-and-white printing mode.
    Image Protect
    The printer employs lossy compression when Off is selected. The printer does not employ 
    lossy compression when On is selected. Lossy compression refers to a data compression 
    technique in which some amount of data is lost.
    Binary
    Specifies the data format. Select On for the Binary data and select Off for the ASCII data.
    Note:
    ❏Binary can only be used with network connection.
    ❏You do not have to select On when using AppleTalk.
    To use the Binary data, make sure your application supports Binary data and that SEND 
    CTRL-D Before Each Job and SEND CTRL-D After Each Job are set to No.
    When this setting is set to On, you cannot use TBCP (Tagged binary communication 
    protocol) in the printer driver settings.
    Item Settings (default in bold)
    Error SheetOff, On
    ColorationColor, Mono
    Image ProtectOff, On
    Binary
    *Off, On
    Text DetectionOff, On
    PDF Page SizeAuto, A4, A5, B5, LT, HLT, LGL, GLT, GLG, EXE, DL, C5, IB5
     
    						
    							Using the Control Panel185
    EPSON AcuLaser C3800 Users Guide
    Text Detection
    When you select On, the text file is converted to a PostScript file when printing. This setting 
    is available only when you select PS3 in the Emulation Menu.
    PDF Page Size
    Specifies the paper size when you send the PDF file directory from a computer or some 
    other device. If Auto is selected, the paper size is determined based on the size of the first 
    page that is printed.
    Password Config Menu
    This menu allows you to restrict operation of the printer.
    *The default password is Null. You can enter up to 20 characters for the password.
    Password Config
    Changes the password. Enter the old password first and then enter the new password 
    twice.
    To enter the password, press the dDown or uUp button to select the character and press 
    the Enter button to determine the character. After all characters are determined, select 
     and press the Enter button.
    Limitation
    Changes the restriction range. When Interface is selected, the password is required to 
    change the settings in the USB, Network, AUX, and USB Host menus. When Config is 
    selected, the password is required to change the settings in all menus. When All is 
    selected, the password is required to change the settings and to perform all items in all 
    menus. Before changing the setting, you have to enter the password set in the 
    Password Config setting.
    Item  Settings (default in bold)
    Password Config
    *-
    LimitationDisable, Interface, Config, All
     
    						
    							Using the Control Panel186
    EPSON AcuLaser C3800 Users Guide
    ESCP2 Menu
    This menu allows you to make settings which affect the printer when it is in the ESC/P 2 
    emulation mode.
    * Depending on whether Letter (62) or A4 (66) paper has been selected.
    Font
    Selects the font.
    Pitch
    Selects the pitch (the horizontal spacing) of the font in fixed pitch, measured in cpi 
    (characters per inch). You can also choose proportional spacing.
    Condensed
    Turns condensed printing on or off.
    Item Settings (default in bold)
    FontCourier, Prestige, Roman, Sans serif, Roman T, Orator S, Sans H, Script, OCR A, 
    OCR B
    Pitch10, 12, 15 cpi, Prop.
    CondensedOff, On
    T. Margin 0.40 ... 0.50 ... 1.50 inches in 0.05-inch increments
    Text 1... 62/66*... 81 lines
    CGTablePcUSA, Italic, PcMultilin, PcPortugue, PcCanFrenc, PcNordic, PcTurkish2, 
    PcIcelandic, PcE.Europe, BpBRASCII, BpAbicomp, Roman-8, PcEur858, ISO 
    Latin1, 8859-15ISO, PcSI437, PcTurkish1, 8859-9 ISO, Mazowia, CodeMJK, 
    PcGk437, PcGk851, PcGk869, 8859-7 ISO, PcCy855, PcCy866, PcUkr866, 
    PcLit771, Bulgarian, Hebrew7, Hebrew8, PcHe862, PcAr864, PcAr864Ara, 
    PcAr720, PcLit774, Estonia, ISO Latin2, PcLat866
    CountryUSA, France, Germany, UK, Denmark, Sweden, Italy, Spain1, Japan, Norway, 
    Denmark2, Spain2, LatinAmeric, Korea, Legal
    Auto CROn, Off
    Auto LFOff, On
    Bit ImageDark, Light, BarCode
    ZeroChar0, (or the zero character with a slash)
     
    						
    							Using the Control Panel187
    EPSON AcuLaser C3800 Users Guide
    T. Margin
    Sets the distance from the top of the page to the baseline of the first printable line. The 
    distance is measured in inches. The smaller the value, the closer the printable line is to the 
    top.
    Text
    Sets the page length in lines. For this option, a line is assumed to be 1 pica (1/6 inch). If 
    you change the Orientation, Page Size, or T. Margin settings, the page length setting 
    automatically returns to the default for each paper size.
    CG Table
    Use the character generator (CG) table option to select the graphics character table or the 
    italics table. The graphics table contains graphic characters for printing lines, corners, 
    shaded areas, international characters, Greek characters, and mathematical symbols. If 
    you select Italic, the upper half of the character table is defined as italic characters.
    Country
    Use this option to select one of the fifteen international symbol sets. See the Font Guide for 
    samples of the characters in each country’s symbol set.
    Auto CR
    Specifies whether the printer performs a carriage-return/line-feed (CR-LF) operation 
    whenever the printing position goes beyond the right margin. If you select Off, the printer 
    does not print any characters beyond the right margin and does not perform any line 
    wrapping until it receives a carriage-return character. This function is handled 
    automatically by most applications.
    Auto LF
    If you select Off, the printer does not send an automatic line-feed (LF) command with each 
    carriage-return (CR). If On is selected, a line-feed command is sent with each 
    carriage-return. Select On if your text lines overlap.
    Bit Image
    The printer is able to emulate the graphics densities set with the printer commands. If you 
    select Dark, the bit image density is high, and if you select Light, the bit image density is 
    low.
    If you select BarCode, the printer converts bit images to bar codes by automatically filling in 
    any vertical gaps between dots. This produces unbroken vertical lines that can be read by 
    a bar code reader. This mode will reduce the size of the image being printed, and may also 
    cause some distortion when printing bit image graphics.
     
    						
    							Using the Control Panel188
    EPSON AcuLaser C3800 Users Guide
    ZeroChar
    Specifies whether the printer prints a slashed or unslashed zero.
    FX Menu
    This menu allows you to make settings which affect the printer when it is in the FX 
    emulation mode.
    * Depending on whether Letter (62) or A4 (66) paper has been selected.
    Font
    Selects the font.
    Pitch
    Selects the pitch (the horizontal spacing) of the font in fixed pitch, measured in cpi 
    (characters per inch). You can also choose proportional spacing.
    Condensed
    Turns condensed printing on or off.
    Item Settings (default in bold)
    FontCourier, Prestige, Roman, Sans serif, Script, Orator S
    Pitch10, 12, 15 cpi, Prop. 
    CondensedOff, On
    T. Margin 0.40 ... 0.50 ... 1.50 inches in 0.05-inch increments
    Text 1... 62/66*... 81 lines
    CGTablePcUSA, Italic, PcMultilin, PcPortugue, PcCanFrenc, PcNordic, PcTurkish2, 
    PcIcelandic, PcE.Europe, BpBRASCII, BpAbicomp, Roman-8, PcEur858, ISO 
    Latin1, 8859-15ISO
    CountryUSA, France, Germany, UK, Denmark, Sweden, Italy, Spain1, Japan, Norway, 
    Denmark2, Spain2, LatinAmeric
    Auto CROn, Off
    Auto LFOff, On
    Bit ImageDark, Light, BarCode
    ZeroChar0, (or the zero character with a slash)
     
    						
    							Using the Control Panel189
    EPSON AcuLaser C3800 Users Guide
    T. Margin
    Sets the distance from the top of the page to the baseline of the first printable line. The 
    distance is measured in inches. The smaller the value, the closer the printable line is to the 
    top.
    Text
    Sets the page length in lines. For this option, a line is assumed to be 1 pica (1/6 inch). If 
    you change the Orientation, Page Size, or T. Margin settings, the page length setting 
    automatically returns to the default for each paper size.
    CG Table
    Use the character generator (CG) table option to select the graphics character table or the 
    italics table. The graphics table contains graphic characters for printing lines, corners, 
    shaded areas, international characters, Greek characters, and mathematical symbols. If 
    you select Italic, the upper half of the character table is defined as italic characters.
    Country
    Use this option to select one of the fifteen international symbol sets. See the Font Guide for 
    samples of the characters in each country’s symbol set.
    Auto CR
    Specifies whether the printer performs a carriage-return/line-feed (CR-LF) operation 
    whenever the printing position goes beyond the right margin. If you select Off, the printer 
    does not print any characters beyond the right margin and does not perform any line 
    wrapping until it receives a carriage-return character. This function is handled 
    automatically by most applications.
    Auto LF
    If you select Off, the printer does not send an automatic line-feed (LF) command with each 
    carriage-return (CR). If On is selected, a line-feed command is sent with each 
    carriage-return. Select On if your text lines overlap.
    Bit Image
    The printer is able to emulate the graphics densities set with the printer commands. If you 
    select Dark, the bit image density is high, and if you select Light, the bit image density is 
    low.
    If you select BarCode, the printer converts bit images to bar codes by automatically filling in 
    any vertical gaps between dots. This produces unbroken vertical lines that can be read by 
    a bar code reader. This mode will reduce the size of the image being printed, and may also 
    cause some distortion when printing bit image graphics.
     
    						
    							Using the Control Panel190
    EPSON AcuLaser C3800 Users Guide
    ZeroChar
    Selects whether the printer prints a slashed or unslashed zero.
    I239X Menu
    The I239X mode emulates IBM® 2390/2391 Plus commands.
    These settings are available only when the printer is in the I239X mode.
    *1Depends on whether Letter (63) or A4 (67) paper has been selected.
    *2Depends on whether Letter (1) or A4 (2) paper has been selected.
    Font
    Selects the font.
    Pitch
    Selects the pitch (the horizontal spacing) of the font in fixed pitch, measured in cpi 
    (characters per inch). You can also choose proportional spacing.
    Code Page
    Selects the character tables. Character tables contain the characters and symbols used by 
    different languages. The printer prints text based on the selected character table.
    Item Settings (default in bold)
    FontCourier, Prestige, Gothic, Orator, Script, Presentor, Sans serif
    Pitch10, 12, 15, 17, 20, 24 cpi, Prop.
    Code Page437, 850, 858, 860, 863, 865
    T. Margin 0.30 ... 0.40 ...1.50 inches in 0.05-inch increments
    Text 1 ... 63/67
    *1... 81 lines
    Auto CROff, On
    Auto LFOff, On
    Alt. GraphicsOff, On
    Bit ImageDark, Light
    ZeroChar0, (or the zero character with a slash)
    CharacterSet1
    *2, 2*2
     
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson AcuLaser C3800N User Manual