Epson AcuLaser C3800N User Manual
Have a look at the manual Epson AcuLaser C3800N User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Using the PostScript Printer Driver151 EPSON AcuLaser C3800 Users Guide For Macintosh Any Macintosh computer to which the printer is connected must be running Mac OS 9 ver. 9.1 or later, or Mac OS X ver. 10.2.8 or later. See the following table for details. Note: To use the PostScript 3 printer driver with a USB interface, your computer must be Macintosh OSX 10.3.9 or later. Mac OS X Note: To use binary data, Epson recommends that you use AppleTalk for the printer’s network connection. If you use a protocol other than AppleTalk for the network connection, you need to set Binary to On in the PS3 Menu on the control panel. If you use the printer with a local connection, you cannot use binary data. Mac OS 9 Note: To use binary data, Epson recommends that you use AppleTalk for the printer’s network connection. If you use a local connection or a protocol other than AppleTalk for the network connection, you cannot use binary data. c Caution: ❏The Adobe PostScript 3 printer driver cannot be used on computers running System 9.0.x or below. ❏The Adobe PostScript 3 printer driver cannot be used on Macintosh 68K computers. Memory8 MB 16 MB Minimum Recommended ComputerPower Mac G3, G4, G5, iMac, eMac, PowerBook G3, G4, or iBook Hard Disk— Memory128 MB Minimum Recommended ComputerPower PC Hard Disk3.1 MB free (for driver installation) 4 MB free (for driver installation) Memory4 MB 32 MB
Using the PostScript Printer Driver152 EPSON AcuLaser C3800 Users Guide Note: For best results, you should connect the printer directly to the computer’s USB port. If multiple USB hubs must be used, we recommend that you connect the printer to the first-tier hub. Using the PostScript Printer Driver with Windows To print in the PostScript mode, you will have to install the printer driver. See the appropriate sections below for installation instructions according to the interface that you are using to print. Installing the PostScript printer driver for the USB interface Follow the steps below to install the PostScript printer driver for the USB interface. c Caution: Never use EPSON Status Monitor and PostScript 3 driver at the same time when the printer is connected via USB port. It may damage the system. Note: ❏For Windows Me or 98, if the Windows driver and the Adobe PS driver for Epson printers with a USB connection have already been installed on your computer, skip the step 3 to 6 in the installation procedure below. If you have not installed an Epson USB printer driver on your computer, follow all the steps below. ❏Installing the printer software for Windows XP, XP x64, or 2000 may require administrator privileges. If you have problems, ask your administrator for more information. ❏Turn off all virus protection programs before installing the printer software. 1. Make sure that the printer is turned off. Insert the printer software CD-ROM into your CD-ROM drive. 2. Connect your computer to the printer with a USB cable, then turn on the printer. 3. Install the USB Device Driver. For Windows Me, select Automatic search for a better driver (Recommended), click Next, then go to step 6. For Windows 98, click Next in the Add New Hardware Wizard. Select Search for best driver for your device (Recommended), then click Next. Note: For Windows XP, XP x64, or 2000, a USB Device Driver is installed automatically. Go to step 7.
Using the PostScript Printer Driver153 EPSON AcuLaser C3800 Users Guide 4. Select Specify a location, then specify the following path for the CD-ROM. If your CD-ROM drive is D:, the path will be D:\ADOBEPS\ENGLISH\WIN9X\PS_SETUP Then click Next. 5. Click Next to continue. 6. When installation of the USB Device Driver is done, click Finish. 7. For Windows 2000, Me, or 98, click Start, point to Settings, and click Printers. Then double-click the Add Printer icon. For Windows XP or XP x64, click Start, point to Printer and Faxes, and click Add a printer in the Printer Tasks menu. 8. The Add Printer Wizard appears. Then click Next. 9. For Windows Me or 98, go to step 11. For Windows XP, XP x64, or 2000, select Local printer, then click Next. Note: For Windows XP, XP x64, or 2000, do not select the Automatically detect and install my Plug and Play printer check box. 10. Select USB as the port the printer is connected to, then click Next. 11. Click Have Disk and specify the following path for the CD-ROM. If your CD-ROM drive is D:, the path will be D:\ADOBEPS\ENGLISH\Folder Name\PS_SETUP Then click OK. Note: ❏Change the drive letter as needed for your system. ❏The folder name differs depending on your operating system version. 12. Select the printer, then click Next. 13. For Windows Me or 98, select USB as the port the printer is connected to, then click Next. For Windows XP, XP x64, or 2000, go to the next step. 14. Follow the on-screen instructions for the rest of the installation. 15. When installation is done, click Finish. Operating system version Folder Name Windows Me or 98 WIN9X Windows XP, XP x64, or 2000 WIN2K_XP
Using the PostScript Printer Driver154 EPSON AcuLaser C3800 Users Guide Installing the PostScript printer driver for the network interface See the appropriate sections below according to your operating system, and follow the instructions to install the PostScript printer driver for the network interface. Note: ❏Set the network settings before installing the printer driver. Refer to the Network Guide that comes with your printer for details. ❏Turn off all virus protection programs before installing the printer software. For Windows XP, XP x64, or 2000 users 1. Make sure that the printer is turned on. Insert the printer software CD-ROM into your CD-ROM drive. 2. For Windows XP, or XP x64, click Start, point to Printer and Faxes, and click Add a printer in the Printer Tasks menu. For Windows 2000, click Start, point to Settings, and click Printers. Then double-click the Add Printer icon. 3. The Add Printer Wizard appears. Then click Next. 4. Select Local printer, then click Next. Note: Do not select the Automatically detect and install my Plug and Play printer check box. 5. Select the Create a new port check box and select Standard TCP/IP Port from the drop-down list. Click Next. 6. Click Next to continue. 7. Specify the IP address and port name, then click Next. 8. Click Finish. 9. Click Have Disk in the Add Printer Wizard and specify the following path for the CD-ROM. If your CD-ROM drive is D:, the path will be D:\ADOBEPS\ENGLISH\WIN2K_XP\PS_SETUP. Then click OK. Note: Change the drive letter as needed for your system. 10. Select the printer and click Next. 11. Follow the on-screen instructions for the rest of the installation. 12. When installation is done, click Finish.
Using the PostScript Printer Driver155 EPSON AcuLaser C3800 Users Guide For Windows Me or 98 users 1. Install the EpsonNet Print. Refer to “Installing EpsonNet Print” in the Network Guide to find the instructions. 2. Install the printer driver. See Installing the PostScript printer driver for the USB interface on page 152 for details. 3. Set the printer port to EpsonNet Print Port. Refer to “Configuring the Printer Port” in the Network Guide to find the instructions. Note: High-speed Printing (RAW) is not supported. Accessing the PostScript printer driver You can access the PostScript printer driver directly from any application programs, from your Windows operating system. The printer settings made from many Windows applications override the setting made when the printer driver is accessed from the operating system, so you should access the printer driver from your application to make sure that you get the result you want. From the application To access the printer driver, click the Print or Page Setup from the File menu. You also need to click Setup, Options, Properties, or a combination of these buttons. For Windows XP or XP x64 users To access the printer driver, click Start, click Printers and Faxes, then click Printers. Right-click your printer icon, then click Printing Preferences. For Windows Me or 98 users To access the printer driver, click Start, point to Settings, then click Printers. Right-click your printer icon, then click Properties. For Windows 2000 users To access the printer driver, click Start, point to Settings, then click Printers. Right-click your printer icon, then click Printing Preferences.
Using the PostScript Printer Driver156 EPSON AcuLaser C3800 Users Guide Making changes to PostScript printer settings You can change the PostScript printer settings in the PostScript printer driver. Online help is available to help you with the printer driver settings. Using online help If you want help on a particular item, click the “?” icon on the top-right corner of the dialog box’s title bar, then click the name of the setting that you want more information on. An explanation of the setting and its options will be displayed. Using AppleTalk under Windows 2000 Use the following settings if your machine is running Windows 2000, and the printer is connected through an network interface using the AppleTalk protocol: ❏Use SelecType to set the Emulation Mode-Network item to PS3. Using the default Auto setting will cause an extra, unneeded page to be printed. ❏On the Device Settings sheet of the printer’s Properties dialog box, make sure that SEND CTRL-D Before Each Job and SEND CTRL-D After Each Job are set to No. ❏TBCP (Tagged binary communications protocol) cannot be used as the Output Protocol setting. ❏On the Job Settings sheet of the printer’s Properties dialog box, make sure to clear the Job Management On check box. Using the PostScript Printer Driver with Macintosh Installing the PostScript printer driver Follow the steps below to install the PostScript printer driver. Note: Make sure that no applications are running on your Macintosh before installing the printer driver. For Mac OS X users Note: Make sure that Printer Setup Utility (for Mac OS X 10.3 and 10.4) or Print Center (for Mac OS X 10.2) is not open.
Using the PostScript Printer Driver157 EPSON AcuLaser C3800 Users Guide 1. Insert the printer software CD-ROM into your CD-ROM drive. 2. Double-click the CD-ROM icon. 3. Double-click Mac OS X, then double-click PS Installer. Note: For Mac OS X 10.2, if the Authenticate window appears, enter the user name and password for an administrator. 4. The Install EPSON PostScript Software screen appears, click Continue, then follow the on-screen instructions. 5. Easy Install is displayed on the screen. Click Install. Note: For Mac OS X 10.3 and 10.4, if the Authenticate window appears, enter the user name and password for an administrator. 6. When installation is done, click Close. For Mac OS 9 users 1. Insert the printer software CD-ROM into your CD-ROM drive. 2. Double-click the CD-ROM icon. 3. Double-click Mac OS 9, then double-click English. 4. Double-click AdobePS 8.7, and double-click AdobePS Installer. Then follow the on-screen instructions. 5. Select Easy Install, then click Install. 6. When installation is done, click Quit. Note: If you are connecting two or more EPSON printers of the same model using AppleTalk, and you want to rename the printer, see the Network Guide. Selecting the printer After installing the PostScript 3 printer driver, you need to select the printer.
Using the PostScript Printer Driver158 EPSON AcuLaser C3800 Users Guide Selecting the printer when it is connected via a USB connection for Mac OS 9 users If the printer is connected to your computer via a USB port, you will not be able to select the printer from the Chooser. You will have to launch the Apple Desktop Printer Utility, then register the printer as a Desktop Printer. The Desktop Printer Utility is automatically installed when you install the Adobe PostScript printer driver. Follow the steps below to select the printer and to create a Desktop Printer. Note: When printing via the USB port from a Power Macintosh running Mac 0S 9, the printer must be set to handle ASCII data. To specify this setting, select Print from the File menu of the application that you are using, then select the name of the application from the options available in the Print dialog box. On the setup option page that appears, select ASCII for the data format setting. The actual setting name varies by application, but is often called Encoding or Data. 1. Open the AdobePS Components folder in your hard disk, then double-click the Desktop Printer Utility. 2. The New Desktop Printer dialog box appears. Select AdobePS from the With pop-up menu, click Printer (USB) in the Create Desktop list, then click OK. 3. Click Change in USB Printer Selection. 4. The USB Printer dialog box appears. Select your printer from the list of connected USB printers, then click OK. 5. Click Auto Setup to select the PostScript Printer Description (PPD) file. When a PPD file is selected, the selected printer name will be displayed under the printer icon. If the printer name is incorrect, click Change, then select the correct PPD file. 6. After the USB printer and PPD file have been selected, click Create. A warning message suggesting to save changes to desktop printer appears. Select Save. 7. Select Save to continue. The USB printer icon will be displayed on the desktop. Selecting a printer in a network environment If the printer is connected through the Ethernet interface or an optional network card. For Mac OS X users Follow the steps below to select the printer.
Using the PostScript Printer Driver159 EPSON AcuLaser C3800 Users Guide Note: ❏You cannot use FireWire for printer connection in the PostScript 3 mode. Although EPSON FireWire appears in the interface pop-up list, it cannot be used with the PostScript 3 printer driver. ❏You need to make the settings for your installed options manually when the printer is connected using USB, IP printing, or Bonjour (Rendezvous). When the printer is connected using AppleTalk, the printer software automatically makes the settings. ❏Make sure to specify ASCII as the data format in the application. 1. Open the Applications folder, open the Utilities folder, then double-click Printer Setup Utility (for Mac OS X 10.3 and 10.4) or Print Center (for Mac OS X 10.2). The Printer List window appears. 2. Click Add in the Printer List window. 3. Select the protocol or the interface that you are using from the pop-up list. Note for Appletalk users: Make sure to select AppleTalk. Do not select EPSON AppleTalk, because it cannot be used with the PostScript 3 printer driver. Note for IP Printing users: ❏Make sure to select IP Printing. Do not select EPSON TCP/IP, because it cannot be used with the PostScript 3 printer driver. ❏After selecting IP Printing, enter the IP address for the printer, then make sure to select the Use default queue on server check box. Note for USB users: Make sure to select USB. Do not select EPSON USB, because it cannot be used with the PostScript 3 printer driver. 4. Follow the instructions as appropriate below to select your printer. AppleTalk Select your printer from the Name List, then select Auto Select from the Printer Model List. IP Printing Select Epson from the Name List, then select your printer from the Printer Model List. USB Select your printer from the Name List, then select your printer from the Printer Model List. Note for Mac OS X 10.3 and 10.4 users: If ESC/Page driver is not installed, your printer model is automatically selected in the Printer Model List when you select your printer from the Name List while the printer is on.
Using the PostScript Printer Driver160 EPSON AcuLaser C3800 Users Guide Bonjour (Rendezvous) Select your printer, the printer name is followed by (PostScript), from the Name List. Your printer model is automatically selected in the Printer Model List. Note for USB (for Mac OS X 10.2) or Bonjour (Rendezvous) users: If your printer model is not automatically selected in the Printer Model list, you need to reinstall the PostScript printer driver. See Installing the PostScript printer driver on page 156. 5. Click Add. Note for IP Printing users, USB or Bonjour (Rendezvous) users: Select your printer from the Printer list, then select Show Info from the Printers menu. The Printer Info dialog box appears. Select Installable Options from the pop-up list, then make the necessary settings. 6. Confirm that your printer’s name is added to the Printer List. Then quit Printer Setup Utility (for Mac OS X 10.3 and 10.4) or Print Center (for Mac OS X 10.2). For Mac OS 9 users Follow the steps below to select the printer. 1. Select Chooser from the Apple menu. 2. Make sure that AppleTalk is active. 3. Click the AdobePS icon and select the network to be used in the AppleTalk Zone box. Your printer appears in the Select a PostScript Printer box. Note: By default, the six-digit MAC address is displayed after the printer name if the printer is connected through an optional network card. Refer to your network card manual for details. 4. Click your printer. The Create button appears. Note: If your computer is connected to more than one AppleTalk zone, click the AppleTalk zone your printer is connected to in the AppleTalk Zones list. 5. Click Create. Accessing the PostScript printer driver To control your printer and change its settings, use the printer driver. The printer driver allows you to easily make all the print settings, including paper source, paper size, and orientation.