EMAK Lawn Mower 91-93 Instructions Manual

the grass cuttings, this is also a safety
element that stops any objects drawn up
by the blades from being thrown outside
of the machine.
15. Stone-guard or deflector (optional):
this can be fitted in place of the grass-
catcher and prevents objects drawn up
by the blades from being thrown outside
of the machine.  
16. Engine: this moves the blades and drives the wheels. Its specifications and regu-
lations for use are described in a specific manual.
17. Battery: provides the energy for starting the...

For storage and transport purposes, some components of the machine are not
installed in the factory and have to be assembled after unpacking. Follow the instruc-
tions below.
The machine is supplied without engine oil or fuel. Before starting
the engine, fill with oil and fuel following the instructions given in the engine manual.
3.1 UNPACKING
When unpacking the machine, take care to gather all individual parts and fittings, and
do not damage the cutting deck when taking the machine off the pallet.
The...

with the hole on the shaft and insert the pin (3) using a hammer. Make sure the end
comes right through to the opposite side.
To avoid damage to the steering wheel, use a punch or a screw-
driver of the same size as the pin when hammering it through the hole.
3.3 FITTING THE SEAT
Mount the seat (1) on the plate (2) using the
screws (3).
3.4 MOUNTING THE FRONT BUMPER
(if provided)
Mount the front bumper (1) on the bottom of
the frame (2) using the four screws (3).
3.5 ASSEMBLY AND CONNECTING THE BATTERY...

on the inner tongue with the help of a small screwdriver.
First connect the red wire (8) to the positive
pole (+) and then the black wire (9) to the
negative pole (–), using the screws supplied
as shown. 
Apply silicone grease to the terminals and
check that the protective cap for the red wire
(8) is in place.  
Replace the battery in its housing making
sure that the two poles are facing the centre
of the machine, fully tighten the clamp (3)
and refit the guard (2).
Always fully charge the battery...

12EN
4.1 STEERING WHEEL
Turns the front wheels.
4.2 THROTTLE
This regulates the engines r.p.m. The positions are indicated on a plate showing the
following symbols:
«CHOKE» cold starting 
«SLOW» for minimum engine speed
«FAST»  for maximum engine speed
– The «CHOKE» position enriches the mixture so must only be used for the time nec-
essary when starting from cold.
– When moving from one area to another, put the lever in a position between «SLOW»
and «FAST».
– When cutting, shift into «FAST».
4.3 KEY...

13ENCONTROLS AND INSTRUMENTS
«START»  connects the starter motor.
If you release the key on «START», it will automatically return to «ON».
4.4 PARKING BRAKE
This brake stops the machine from moving when it has been parked. There are two
positions:
«A» = Brake off
«B» = Brake on
– The brake is applied by pressing the pedal right down (4.21 or 4.31) and moving the
lever to position «B». When you take your foot off the pedal it will be blocked by the
lever in the lowered position.
– To disengage the parking...

14EN
b)sack or stone guard missing;
c)blades engaged;
d)no operator present;
e)gear in “neutral”;
f)fault in battery charger (with engine
running).
4.7 BLADE ENGAGEMENT AND BRAKE CONTROL
The mushroom switch allows you to engage the blades using the electromagnetic
clutch:
«A» Pressed = Blades disengaged
«B» Pulled = Blades engaged 
– If you engage the blades without taking the necessary safety precautions, the
engine shuts down and cannot be restarted  (☛5.2).
– Blade disengagement (Pos. «A»),...

15ENCONTROLS AND INSTRUMENTS
4.21 CLUTCH / BRAKE PEDAL
This pedal has two functions: during the first part of its travel it acts as a clutch,
engaging and disengaging drive to the wheels, and in the second part it acts as a
brake on the rear wheels
Do not keep the pedal halfway between clutch engagement or
disengagement, as this can cause overheating and damage the transmission belt.
When the machine is moving, keep your foot off the pedal.
4.22 SPEED CHANGE LEVER
This lever has seven positions for the 5...

4.31 BRAKE PEDAL
This pedal works the brake on the rear wheels.
4.32 DRIVE PEDAL
This pedal engages drive in the wheels and controls the machines forward and
reverse speeds.
– To engage forward drive, press it towards «F» with your toe-cap. As you increase
the pressure on the pedal, the speed of the machine increases.
– Reverse is engaged by pressing the pedal with the heel towards «R».
– The pedal automatically goes into neutral «N» when released.
Only shift into reverse when the machine has stopped...

HOW TO USE THE MACHINE17EN
5.1 SAFETY RECOMMENDATIONS
The machine must only be used for the purpose for which it
was designed (cutting and collecting grass). 
Do not tamper with or remove the safety devices fitted on the machine.
REMEMBER THAT THE USER IS ALWAYS RESPONSIBLE FOR DAMAGE AND
INJURY TO OTHERS. Before using the machine:
– read the general safety regulations ( ☛ 1.2), paying particular attention to
driving and cutting on slopes;
– carefully read the instructions for use, make sure you are...