Dell M 5200 Manual

Install optional memory cards31
Installing printer memory
 NOTICE: Electronic components can be damaged by static electricity. Touch something metal 
on the printer before you touch the memory option.
Your printer comes with 64MB memory. You can buy optional memory cards to increase 
printer memory up to 320MB.
  CAUTION: Before performing any of the following procedures, read and follow 
the safety instructions.
1
Unpack the optional printer memory card. Avoid touching the connection points 
along its...

32Install optional memory cards
www.dell.com/supplies | support.dell.com
2Open both latches on the connector completely.
3Align the notches on the memory card with the ridges on the connector.
1Memory connector 1
2Memory connector 2
1Ridge
2Notch
1
2
1
2 

Install optional memory cards33
4Push the memory card straight into the connector until it snaps into place. Make sure 
each latch fits over the notch located on either side of the memory card.
1Latch
2Notch
1
2 

34Install optional memory cards
www.dell.com/supplies | support.dell.com
Replacing the shield
Follow these steps to reattach the shield and close the doors.
  CAUTION: Before performing any of the procedures listed below, read and follow 
the safety instructions.
1
Grasp the shield by the tabs and align the three keyholes on the shield with the top 
three screws. Holding the shield by the tabs, slide it down onto the screws. Tighten all 
six screws.
2Close the side door.
3Close the upper door and the...

3
SECTION 3
Set up for local 
printing
Installing printer drivers 

36Set up for local printing
www.dell.com/supplies | support.dell.com
A local printer is a printer attached to your computer using a USB cable. If your printer is 
attached to a network instead of your computer, go on to “Set up for network printing” on 
page 11. 
Installing printer drivers
A printer driver is software that lets your computer communicate with your printer. To 
obtain all the features described in “Utilizing additional software tools” on page 61, use the 
Drivers and UtilitiesCD to install...

Set up for local printing37
Using Windows XP
 NOTE: Business versions of Windows XP require that you have administrative access to install 
printer drivers on your computer.
When you attached the cable and turned on the printer, the Found New Hardware Wizard 
appeared on your computer screen. 
1Insert the Drivers and UtilitiesCD into your computer. 
The Wizard automatically searches for an appropriate driver.
2Scroll through the list of drivers until you see D:\drivers\win_2000\dkaag1da.inf 
selected in...

38Set up for local printing
www.dell.com/supplies | support.dell.com
Using Windows 2000
When you attached the cable and turned on the printer and computer, the Found New 
Hardware Wizard screen appeared on your computer screen.
1Insert the Drivers and UtilitiesCD, and then click Next. 
2Select Search for a suitable driver, and then click Next.
3Select Specify a location only, and then click Next.
4Browse to the location of the printer driver on the Drivers and UtilitiesCD. 
D:\Drivers\Win_2000\
Replace...

Set up for local printing39
Using Windows Me 
 NOTE: Depending on the software and printers already installed on your computer, your screens 
may vary from those in the instructions.
You must install both a USB port driver and a custom print driver. 
When you attached the cable and turned on the printer and computer, the Add New 
Hardware Wizard screen appeared on your computer screen.
1Insert the Drivers and UtilitiesCD.
The Wizard automatically searches for the USB driver on the CD and installs it....

40Set up for local printing
www.dell.com/supplies | support.dell.com
5Click Next to install the printer driver.
6Click Next to complete installation.
7Use the default printer name (for example, Dell Laser Printer M5200) or type a unique 
name for your printer, and then click Next.
8Click Yes (recommended), and then click Fi ni sh to print a test page. 
9After the test page prints, click Ye s to close the window.
10Click Fi ni sh to complete the installation and close the wizard. 
11Launch the Drivers and...