DELL 2335dn User Manual

3.The Network Configuration page prints out.
Setting Network Protocols
When you first install and power up the printer, all supported network protocols are enabled.  If a network
protocol is enabled  , the printer may actively transmit on the network even when the protocol is not in use.
This may slightly increase network traffic. To eliminate unnecessary traffic, you may disable unused
protocols.
Press  Scroll  (
 or 
 ) to highlight  Setup and then press  Select (
 ).
1.
Press  Scroll  (
 or 
 ) to...

To enter the TCP/IP setting from your printers operator panel, take the following steps:
Press Scroll  (
 or 
 ) to highlight  Setup and then press  Select (
 ).
1.
Press  Scroll  (
 or 
 ) to highlight  Network Setup  and then press  Select (
 ).
2.
Press  Scroll  (
 or 
 ) to select the network protocol you want to use and then press  Select (
 ).
3.
If you selected TCP/IP (IPv4)  .
Press Scroll  (
 or 
 ) to select  IPv4 Activate  and then press  Select (
 ).
a.
Press  Scroll  (
 or 
 ) to change the...

7.
An IP address consists of 4 bytes.
Enter the numbers from the keypad and use  Scroll (
 or 
 ) to move between octets and then
press  Select  (
 ).
8.
Enter other parameters, such as the  Subnet Mask or  Gateway  , and then press  Select (
 ).
9.
After entering all parameters, press  Cancel (
 ) to return to the Standby mode.
10.
Dynamic Addressing (BOOTP/DHCP)
To assign the TCP/IP address automatically using a DHCP or BOOTP server on your network.
Press Scroll  (
 or 
 ) to highlight  Setup and then...

5.
Setting For Special Solutions
When you use a specific printing solution such as  Novell iPrint , you have to configure this feature.
The interpretation of printer status information may differ from the printing solution system. If the
client computer shows a different printer’s status from the status on your printer, try to set this
option.
Press Scroll  (
 or 
 ) to highlight  Setup and then press  Select (
).
1.
Press  Scroll  (
 or 
) to highlight Network Setup  and then press  Select (
).
2.
Press...

Faxing
Setting the Printer ID Sending a Fax
Using the Number Keypad to Enter Characters Receiving a Fax
Setting the Time and Date Automatic Dialing
Setting Daylight Savings Time
Other Ways to Fax
Changing the Clock Mode Additional Features
Setting Sounds Sending a fax from a Computer
Toll Save Mode Fax data back-up
Setting up the Fax System    
 
Setting the Printer ID
In most countries, you are required by law to indicate your fax number on any fax you send. The printer ID,
containing your telephone...

Press Select  (
 ) when the name on the display is correct.
8.
Press  Cancel  (
 ) to return to the Standby mode.
9.
Using the Number Keypad to Enter Characters
As you perform various tasks, you may need to enter names and numbers. For example, when you set up
your printer, you enter your name or your companys name and telephone number. When you store fax
numbers in memory, you may also enter the corresponding names.
When prompted to enter a letter, press the appropriate button until the correct letter...

Key Assigned numbers, letters or characters
1 1 @ . _ space , / * # & $ + - `
2 A B C 2
3 D E F 3
4 G H I 4
5 J K L 5
6 M N O 6
7 P Q R S 7
8 T U V 8
9 W X Y Z 9
0 0
Changing Numbers or Names
If you make a mistake while entering a number or name,  press the left  Scroll (
 ) button to delete the last
digit or character. Then enter the correct number or character.
Inserting a Pause
For some telephone systems, it is necessary to dial an access code and listen for a second dial tone. A pause
must be entered...

4.Month = 01 ~ 12
Day = 01 ~ 31
Year = 2000 ~ 2099
Hour = 01 ~ 12 (12-hour mode)
00 ~ 23 (24-hour mode)
Minute = 00 ~ 59
You can also use  Scroll (
 or 
 ) to move the cursor under the digit you want to correct and enter a
new number.
To select  AM or  PM  for a 12-hour format, press the 
 or the 
 button.
5.
When the cursor is not under the  AM or  PM  indicator, pressing the 
 or the 
 button immediately
moves the cursor to the indicator.
You can change the clock mode to a 24-hour format (e.g. 01:00 PM...

6.
7.
Changing the Clock Mode
You can set your printer to display the current time using either the 12-hour or the 24-hour format.
Press  Scroll  (
 or 
 ) to highlight  Setup and then press  Select (
 ).
1.
Press  Scroll  (
 or 
 ) to highlight  Machine Setup  and then press  Select (
 ).
2.
Press  Scroll  (
 or 
 ) to highlight  Clock Mode and then press  Select (
 ).
3.
The printer displays the Clock mode that is currently set.
Press  Scroll  (
 or 
 ) to select the other mode and then press  Select...

6.
7.
Press  Cancel  (
 ) to return to the Standby mode.
8.
Toll Save Mode
The Toll Save mode can be used to save scanned documents for transmission at a specified time in order to
take advantage of lower long distance rates.
To turn the Toll Save mode on:
Press  Scroll  (
 or 
 ) to highlight  Setup and then press  Select (
 ).
1.
Press  Scroll  (
 or 
 ) to highlight  Fax Setup and then press  Select (
 ).
2.
Press  Scroll  (
 or 
 ) to highlight  Toll Save and then press  Select (
 ).
3.
Press  Scroll...