compaq lte elite User Manual
Have a look at the manual compaq lte elite User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 65 Compaq manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 262
IMPORTANT: When replacing the docking mechanism, ensure that the computer
status sensor is reconnected. If it is not reconnected the
computer cannot dock.
6. Remove the four screws [1], [2] that attach the docking mechanism [3] to
the top cover (Figure 9-19).
IMPORTANT: One of the docking mechanism screws [1] is longer than the
others [2] (Figure 9-19).
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>](http://img.usermanuals.tech/thumb/1258/38935/w64_compaq-lte-elite-261.png "Page 262
IMPORTANT: When replacing the docking mechanism, ensure that the computer
status sensor is reconnected. If it is not reconnected the
computer cannot dock.
6. Remove the four screws [1], [2] that attach the docking mechanism [3] to
the top cover (Figure 9-19).
IMPORTANT: One of the docking mechanism screws [1] is longer than the
others [2] (Figure 9-19).
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>")
![Page 265
(Figure 9-19). If the three screws are tightened first, the
docking mechanism or the 198-pin external options connector
may not align properly.
9. To allow the latch on the AUI connector to clear the top cover, fold
the latch [1] so that it lies against the RJ-45 connector (Figure
9-22).
10. Lift the front of the system board/battery charging compartment
assembly up by the external options connector [2] until the connector
shield [3] is free of the top cover, then carefully tilt the assembly
back to...](http://img.usermanuals.tech/thumb/1258/38935/w64_compaq-lte-elite-264.png "Page 265
(Figure 9-19). If the three screws are tightened first, the
docking mechanism or the 198-pin external options connector
may not align properly.
9. To allow the latch on the AUI connector to clear the top cover, fold
the latch [1] so that it lies against the RJ-45 connector (Figure
9-22).
10. Lift the front of the system board/battery charging compartment
assembly up by the external options connector [2] until the connector
shield [3] is free of the top cover, then carefully tilt the assembly
back to...")
![Page 266
IMPORTANT: When replacing the system board/battery charging compartment
assembly, ensure that the release latch on the AUI connector
lock is folded flat against the RJ-45 connector and that the
harness extension cable is positioned to allow it to connect
to the sensor cable harnesses. In addition, you must press
in the center of the external options connector to enable the
system board to seat properly.
11. Turn the assembly over and remove the battery bezel [1] from the
battery charging compartment by...](http://img.usermanuals.tech/thumb/1258/38935/w64_compaq-lte-elite-265.png "Page 266
IMPORTANT: When replacing the system board/battery charging compartment
assembly, ensure that the release latch on the AUI connector
lock is folded flat against the RJ-45 connector and that the
harness extension cable is positioned to allow it to connect
to the sensor cable harnesses. In addition, you must press
in the center of the external options connector to enable the
system board to seat properly.
11. Turn the assembly over and remove the battery bezel [1] from the
battery charging compartment by...")
IMPORTANT: When replacing the docking mechanism, ensure that the computer status sensor is reconnected. If it is not reconnected the computer cannot dock. 6. Remove the four screws [1], [2] that attach the docking mechanism [3] to the top cover (Figure 9-19). IMPORTANT: One of the docking mechanism screws [1] is longer than the others [2] (Figure 9-19). >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>
9.13 System Board And Battery Charging Compartment >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>
To avoid damage to the cable harnesses or the harness extension cable, be sure to press and hold the lock on the connector before removing the cable harnesses. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
(Figure 9-19). If the three screws are tightened first, the docking mechanism or the 198-pin external options connector may not align properly. 9. To allow the latch on the AUI connector to clear the top cover, fold the latch [1] so that it lies against the RJ-45 connector (Figure 9-22). 10. Lift the front of the system board/battery charging compartment assembly up by the external options connector [2] until the connector shield [3] is free of the top cover, then carefully tilt the assembly back to release it from the top cover (Figure 9-22).
IMPORTANT: When replacing the system board/battery charging compartment assembly, ensure that the release latch on the AUI connector lock is folded flat against the RJ-45 connector and that the harness extension cable is positioned to allow it to connect to the sensor cable harnesses. In addition, you must press in the center of the external options connector to enable the system board to seat properly. 11. Turn the assembly over and remove the battery bezel [1] from the battery charging compartment by gently releasing the two plastic retaining tabs that hold them together (Figure 9-23).
To separate the system board from the battery charging compartment and harness extension cable, complete the following steps: 1. Disconnect the battery contacts board connector from the system board (Figure 9- 24).
2. Turn the assembly over and release the plastic retaining tab that attaches the system board to the battery charging compartment (Figure 9-25).
3. Disconnect the harness extension cable from the system board (Figure 9-26).
9.14 Battery Contacts Board To remove the battery contacts board, complete the following steps: 1. Remove the bottom cover (Section 9.6). 2. Remove any expansion boards that are installed (Section 9.8). 3. Remove the expansion board cage (Section 9.9). 4. Remove the docking mechanism (Section 9.12). 5. Remove the system board and battery charging compartment (Section 9.13). 6. Disconnect the battery contacts board connector from the system board (Figure 9-24). 7. Gently release the two snaps [1] (one at a time) that attach the battery contacts board [2] to the battery charging compartment (Figure 9-27). 8. Guide the battery contacts board connector [3] through the guide hole [4] in the battery charging compartment (Figure 9-27).