compaq lte elite User Manual
Have a look at the manual compaq lte elite User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 65 Compaq manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Screws >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>>
- Display cable - Display latches - Display clutches - Display enclosure 4.10 Keyboard 4.11 Diskette drive and cable 4.12 Hard drive - Hard drive security clips 4.13 Processor board 4.14 Power interface board (PIB) 4.15 PCMCIA ejector rails 4.16 Internal AC power supply 4.17 System board and I/O bracket 4.18 LED cable assembly 4.19 Computer base enclosure 4.20 PCMCIA compartment door 4.21 Battery pack/hard drive release latch assemblies 4.4 Preparation Procedures For Removal And Replacement Before beginning removal and replacement procedures, complete the following steps: 1. Read and observe the precautions in Section 4.1. 2. Turn off the computer. 3. Undock the computer if it is docked in an expansion base or a convenience base (refer to Appendix D, Docking and Undocking). 4. Disconnect the power cord. 5. Remove the battery pack (Section 4.5). 6. Remove any installed diskette. 7. Remove PCMCIA cards. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>
Replacing the Battery Pack To replace the battery pack, complete the following steps: 1. Insert the battery pack with the large label facing up and the battery contacts facing the inside of the battery compartment. 2. Push firmly on the battery pack. When released, it locks into place. 4.6 Memory Expansion Board Random access memory (RAM) can be added to the computer by installing a memory expansion board. Refer to Section 1.6 and Table 3-2 for more information on RAM expansion. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>
Removing the Memory Expansion Board Before removing the memory expansion board, refer to Section 4.4, Preparation Procedures for Removal and Replacement. To remove the memory expansion board, complete the following steps: 1. Turn the unit display-side down. 2. Release the latch on the memory access cover (Figure 4-3). 3. Slide the cover in the direction indicated by the embossed arrow on the cover and remove it. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>
Installing the Memory Expansion Board To install the memory expansion board, complete the following steps: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>>
4.7 Keyboard Cover Before removing the keyboard cover, refer to Section 4.4, Preparation Procedures for Removal and Replacement. To remove the keyboard cover, complete the following steps: 1. Turn the unit display-side down. 2. Remove the five screws located on the bottom and the one screw (shorter than the other five) located near the external options connector on the rear panel (Figure 4-5).
3. Carefully holding the unit together, turn it right-side up. 4. Open the display to its fully open position. 5. Tilt up the back edge of the keyboard cover [1] and lift while rotating the cover toward you to release the front edge [2] (Figure 4-6).
IMPORTANT: When replacing the keyboard cover, angle the front edge of the keyboard cover into place at the front of the computer, ensuring that the tabs on the keyboard cover correctly align with the corresponding recesses on the computer. Gently press the rear edge of the keyboard cover into place at the back of the computer, and verify that the front edge is aligned. If the seam between the computer and the keyboard cover is uneven, remove the keyboard cover and realign the tabs and recesses. 4.8 Auxiliary Battery Refer to Auxiliary Battery in Section 1.6 for more information on the auxiliary battery. To remove the auxiliary battery, complete the following steps: 1. Remove the keyboard cover (Section 4.7). >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION
remove the auxiliary battery connector. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>