compaq lte elite User Manual
Have a look at the manual compaq lte elite User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 65 Compaq manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 126
the factory. To prevent interference with the trackball when
the original trackball shield is reused, the tab for the
trackball shield must go back in its original position (above
or beneath the clutch). When replacing the trackball shield
with a new spare trackball shield (Table 3-11), the mounting
tab always goes beneath the clutch.
4. Remove the two remaining clutch screws (Figure 4-21).
5. Remove the display clutches [1] from the display assembly. (Figure 4-21)
Display Enclosure
NOTE: To replace the...](http://img.usermanuals.tech/thumb/1258/38935/w64_compaq-lte-elite-125.png "Page 126
the factory. To prevent interference with the trackball when
the original trackball shield is reused, the tab for the
trackball shield must go back in its original position (above
or beneath the clutch). When replacing the trackball shield
with a new spare trackball shield (Table 3-11), the mounting
tab always goes beneath the clutch.
4. Remove the two remaining clutch screws (Figure 4-21).
5. Remove the display clutches [1] from the display assembly. (Figure 4-21)
Display Enclosure
NOTE: To replace the...")
![Page 130
front edge of the computer (Figure 4-24).
IMPORTANT: To ensure that the keyboard is reinstalled correctly, be sure
that the metal tabs on the keyboards front edge are properly
aligned (Figure 4-24). The two tabs on the outside [1] go in
the notches on top of the plastic edge at the front of the
computer. The three tabs in the middle [2] tuck underneath
the plastic edge.
4. Replace the two keyboard screws (Figure 4-24).
4.11 Diskette Drive And Cable
The diskette drive cable connects to a LIF connector on...](http://img.usermanuals.tech/thumb/1258/38935/w64_compaq-lte-elite-129.png "Page 130
front edge of the computer (Figure 4-24).
IMPORTANT: To ensure that the keyboard is reinstalled correctly, be sure
that the metal tabs on the keyboards front edge are properly
aligned (Figure 4-24). The two tabs on the outside [1] go in
the notches on top of the plastic edge at the front of the
computer. The three tabs in the middle [2] tuck underneath
the plastic edge.
4. Replace the two keyboard screws (Figure 4-24).
4.11 Diskette Drive And Cable
The diskette drive cable connects to a LIF connector on...")
centered on the drive so that it does not protrude over the plastic ribs of the battery bay or the hard drive bay and interfere with reassembly. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>>>
7. If required, remove the cable from the diskette drive. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>
o Remove and replace the hard drive only when the computer is OFF, unplugged, and the battery pack is removed. Do not remove or replace a hard drive while the computer is ON, in Standby, or in Hibernation. To determine whether the computer is in Hibernation, complete the following steps: a. Turn on the computer and notice whether you are prompted to restore from Hibernation. If you are restoring from Hibernation, let the computer complete this task. b. Save all files and exit all applications. c. Turn off the computer. o Before handling the hard drive, ensure that you are discharged of static electricity. Avoid touching the connectors. o Handle the drive carefully. Do not drop. o When removing the hard drive, immediately place the drive into the hard drive carrying case, which was provided with the computer (Table 3-4). o Avoid exposing the hard drive to temperature extremes. o Avoid exposure to products that have magnetic fields such as monitors or speakers. o Do not spray the hard drive with cleaners or expose it to liquids. o When mailing the hard drive, use the original shipping container for the hard drive, if available. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
NOTE: The hard drive may have either a metal handle (Figure 4-27) or a plastic pull tab that is attached directly to the hard drive enclosure. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>
4. Remove the hard drive from the unit and immediately place it in the hard drive carrying case. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>
Installing the Compaq Diagnostics Utilities on a New Hard Drive To create the hidden partition, install the diagnostics utilities, and format the drive, complete the following steps: 1. Place the Compaq Diagnostics diskette into drive A. 2. Turn on the computer. 3. When the first display screen appears, select Manage Diagnostic Partition. 4. When the Manage Diagnostic Partition screen appears, select Create Diagnostic Partition. The computer creates the partition, reboots the computer, and installs the diagnostics software. 5. Format the C: partition and install other software as necessary. Hard Drive Security Clips If the hard drive security clips are installed, they must be removed before the hard drive can be removed [1]. If the hard drive will not come out easily, or if a hard drive lock label is attached to the hard drive (Figure 4-28), ensure that the hard drive security clips have been removed before attempting to remove the hard drive.
To remove the hard drive security clips, complete the following steps: 1. Remove the keyboard cover (Section 4-7). 2. Reinsert the battery pack halfway into the battery compartment [1] so that the battery pack does not touch the battery contacts on the system board (Figure 4-29). NOTE: The added weight of the battery pack keeps the computer from tipping backward when accessing the hard drive security clips. You may want to insert the battery pack upside down for additional protection against it touching its contacts. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> WARNING >>>>>
4. Remove the two remaining screws on the keyboard [1] (Figure 4-30). >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>
6. Rotate the front edge of the keyboard up and lay it face-down on the cloth-covered display panel (Figure 4-31).
7. Remove the hard drive security clips by gently lifting up on them (Figure 4-32).