Comdial Unisyn System Manual

IMI66-112System Programming
Programming The System -:
.:
3.1 Using Chapter Three
programming the customer’s new system is the most intricate and important aspect of the installer’s job.The benefit
of the Unisyn system is that you can program every system differently to fit each customer’s individual needs.
Chapter 3 is divided into six programming sections:l System,
l Lines,
l Stations,
l Button Mapping,
l Voice Mail,
l Toll Restriction.
Each of these sections lists the applicable features in...

System ProgrammingIMI66-112
3.2.1 Class of Service Programming
The installer performs the Class of Service Programming when the system is first installed. Any programming
function can be done under this type of programming. Class of service programming includes System, Station, and
Line programmin
g.The password for COS programming is *#746*-this places the system in the configuration
mode. You must program from either station 10 or 12.
,3.2.2 Administration Programming
Administrators can use...

ZMZ66-112System Programming3.3 Understanding System
Programming3.3.1 Using A Telephone To Program The System
.-: ,i’ :‘:;; .-.:; :
Perform Class of Service configuration programming from station port 10 or station port 12. The system will not
accept programming commands from any other station port in the system.For best programming results, employ an
LCD speakerphone. While you can install any non-LCD proprietary telephone and use it for programming, visual
feedback of the programming operations will not...

System ProgrammingIMI66-1123.4 Master Clearing
And Svstem Defaults
You can return the entire programming configuration to the factory settings using the master clear procedure.You
can also return the individual system, line, and station class of service configurations to their factory settings using
the system, line, and station default procedures. The operating parameters and class of service values provided by the
factory settings will provide satisfactory performance in a broad range of site...

IMIG-112System Programming3.4.4 Defaulting The Stations
DescriptionReturns the station configuration features to factory settings.To Program: 1.
2.
3.
4.
Press ITCM Dial +N # 7 4 6 +k“CONFIG. MODE”
Dial 
50“STATION DEFAULT ”
Dial 00 to default station ports system-wide,
-OR-
Select individual station port to be defaulted: Station 10 - 25, Dial 10 - 25 or press Al - A16
Dial +i+ for next station to default,
-OR-
Dial +C % for configuration mode or SPKR to quit.
3.4.5 Defaulting Button Assignments...

System ProgrammingIMI66-112
3.5 Programming The System
Programming the system means that you are setting the parameters that will be true system wide. If you are unsure
whether or not you are programming the correct function, check chapter 
5, Description of System Features,in the
back of this manual for a full definition of the feature.You should make a record of all your programming
decisions -it will help you keep track of what you have done and will help you troubleshoot any problem that might
arise...

IMI66-112:System Programming3.5.2 Data Baud Rate
Description:The speed or baud rate of the data bit stream, which carries the SMDR and configuration data between the
system and an external data device, must be programmed to match the requirements of the data device.NOTE: If you use XMODEM protocol for data transfer between a PC and the common equipment, you must use
a-bit data.Data transfer can only be done on port A.
DefauU = W8D IS 1200 (AS, Al6 LED = On)To Program: 1.
Dial 15“BAUD RATE”
2.
Dial 1 for...

System ProgrammingZMZ66-I12
3.5.4 Exclusive Hold
Description:This feature prevents a telephone user at one station from picking up a call that a user placed on hold at
another station. You can enable or disable it system-wide using this procedure.
Default = Disabled (Al LED = Ofl
To Program:1.Dial 23 “XXXXXXX EXC HOLD”
2.Press Al to toggle between enable and disable (LED On = Enable)
-OR-Dial 1 to enable “ENABLE EXC HOLD 
”
Dial 2 to disable “DISABLE EXC HOLD”
3.Dial f for configuration mode.
,
3.5.5...

IMI66112System Programming
3.5.7 System Clock
Description:The system clock maintains current date and time information.The system provides this information to
LCD speakerphones for display. Set the system time with this feature. The system attendant also-has
access to this feature.NOTE: You can enter any attendant programming with the base level entry of 
ITCM t #.
To Program:1.Dial 01 “SET CLOCK ”
LONG FORM
Dial 00 
- 99 for yr.- Dial 00-23 for hr.
Dial 
01 - 12 for mo.- Dial 00-59 for min.
Dial 
01 -...

System ProgrammingZMZ66-1123.5.9 Tone or Voice Signaling
Description:Intercom calls can be tone signaled or voice signaled.Use this programming feature to select the system’s
signaling choice. With either method set as the system’s 
fast choice, the user can choose the other method
as needed by pressing the ITCM key again.
Default = Voice First (Al LED = On)
To Program:1.Dial 16 “JBXXX ANN. FIRST”
2.Press Al to toggle between Voice To Tone. (LED On = voice signaling)
-OR-
Dial 1 for Voice First “VOICE...