Comdial Quick Q Acd Installation Guide

Figure 1-1. Overviewing The QuickQ System
CAJS031G
QuickQ
Digital
Voice
Announcer
DXP
Digital
Communications
System
OO
Print
Scroll
Pa us e
Screen
LockSysRq                                 Brea
kNum
Lock/
*-
InsDelEnter78
9
4
56
123+
0.HomePgUp
EndPgDn
EscF1 F2 F3 F4 F5 F6 F7 F8
F9 F10 F11 F12
Tab
Cap Lock
Shift
CtrlAltBack  Space Insert Home PgUp
Delete            EndPgDnQWERTYUI
OPASDFGHJKLZXCVBNMEnter
Shift
Alt Ctrl~!@
#$
%^&
*()_
+` 1 2 3 4 5 6 7 8               9 0                - =|
{
}
:


?\
[]...

This page remains blank intentionally. 

Section 2
Installing The QuickQ System
This section provides the basic hardware installation requirements for theQuickQsystem.When installing a
Comdial DVA01 in place of aQuickQDVA16, refer to the installation instructions (IMI89-082) packaged with
the equipment.
Reviewing The Installation Check List
Review this list ofQuickQsystem components, suggested additional supplies, and required tools and hardware.
QuickQ Packages
There are threeQuickQpackages available for
upgrading an existing system to a...

DVA Package Contents
The DVA package (purchase part number
ACDXP-DVA16) is separately available and includes
theQuickQDigital Voice Announcer (DVA). The
DVA accessory kit (ACDXP-KIT) includes a 66-type
connector block that is factory-connected to a 25-pair
cable, a software disk, and a power cord). The cable is
terminated with a 50-pin D connector that mates with
a connector on the DVA.
Either one or two Comdial DVAs (DVA01) can be
used on theQuickQsystem as an alternative to the
DVA16. These DVA01 units...

Mounting Considerations
Attach the DVA16 cabinet vertically to any sturdy,
flat surface or vertically rack-mount if desired.
Vertical mounting promotes proper convection air
flow for cooling purposes.
Because of the current listing requirements of UL
1459, the length of the AC line cord on the equipment
cabinet is a maximum length of five feet; therefore,
the cabinet must be located within four feet of a proper
electrical outlet. The equipment requires a dedicated
115 VAC 15–AMP circuit, with a...

Mounting The Optional Wallboards
The installation procedure stated here is intended as a
guide to supplement the installation instructions
included with the wallboards.
1.Unpack and carefully inspect all equipment for
shipping damage. Notify the shipper immediately
of any damage you find. Verify that the packages
contain all parts and accessories needed for proper
installation and operation.
2.After deciding on the location for the wallboard,
you will have to decide on whether to use a
wall-mount,...

Section 3
Wiring The QuickQ System
TheQuickQDigital Voice Announcer (DVA) includes one to four voice channel cards with each card providing
four voice ports. Before wiring, insure that there are sufficient DXP digital station ports available at a station
connector block to interface with the available DVA voice ports (maximum of 16 required). When using the
master channel setup, you need two additional station ports.
CAUTION
You must connect all four voice ports from each voice channel card to station...

Connecting The Personal Computer To The DVA
1.Locate the kit-supplied modular jack that is
labeled LINK ASSEMBLY FROM PC TO
66-BLOCK, and mount it within seven feet of the
computer location.
2.Select the kit-supplied modular to 9-pin EIA
adapter, connect it to the computer’s COM1 serial
data port, and secure the adapter with the screws
provided.
3.Use 6-wire cable to connect the modular jack that
you installed in step 1 with the QuickQ-supplied
66-type connector block.
4.Use a kit-supplied line cord to...

QUICK001
COM1 Serial Data Port
9-Pin D Connector
Rear View of
Typical Personal
Computer (PC)
Kit-Supplied
Modular
to 9-pin
EIA adapter
QuickQ-
Supplied And
Punched-Down
25-Pair Cable
6-Wire Cable
House Wiring
Kit-Supplied
3-Pair Line Cord
64
53
2
1
Front View of Jack
Kit-Supplied Type 625A-6
Modular Jack (LINK ASSEMBLY
FROM PC TO 66-BLOCK)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
501
2
3
4
5
6
7
8
9
10
11
12...

Connecting The Personal Computer To The DXP or DXP Plus
1. Locate a kit-supplied modular jack labeled LINK
ASSEMBLY FROM DXP TO 66-BLOCK FOR
PC, and mount it within seven feet of the DXP
cabinet.
2. Locate a kit-supplied modular jack labeled LINK
ASSEMBLY FROM PC TO 66-BLOCK FOR
OAI, and mount it within seven feet of the
personal computer.
3. Use 6-wire cable to connect the modular jacks that
you installed in steps 1 and 2 to the
QuickQ-supplied 66-type connector block per the
following house wiring...