Comdial ExecuTech Model XE Key System Instructions Manual

STATION 10 - PROGRAMMING OVERLAY 
l Cut out along border. 
l Cut out shaded openin’gs. 
l Fit over station faceplate. 
Al 
A0 
A2 10x14 
PROGR4MMINQ 
OVERLAY A9 
Al0 
A4 All 
Al2 
A6 Al3 
A7 A14 
Bl  

STATION 10 - PROGRAMMING OVERLAY 
l 
Cut out along border. 
l Cut out shaded openings. 
l Fit over station faceplate. 
Al 
A2 
A3 
A4 
A5 
A6 
A7 
B8 
B6 
B4 A8 
5x20 
PROGRAMMING 
OVERLAY A9 
A10 
All 
Al2 
Al3 
A14 
Al5 
B7 
85  

STATION 10 - PROGRAMMING OVERLAY 
l 
Cut out along border. 
l Cut out shaded openings. l Fit over station faceplate. 
Al 
A2 
A4 
A7 A6 
A9 
5x14 A10 
PROGRAMMING 
OVERLAY 
All 
Al2 
Al3 
Al4 
00 00 
=5: 00 
*o 
00 00 
00 00 
00 00 
00 
00  

STATION 10 - PROGRAMMING OVERLAY 
l 
Cut out along border. l Cut out shaded openings. 
l Fit over station faceplate. 
Al 
A2 
A3 
A4 
A5 
A6 
A7 
B7 
B5 
83 
Bl 2x22 
-NG 
WERAY A8 
A9 
A10 
All 
Al2 
Al3 
Al4 
B8 
B6 
B4 
B2  

e lfh66-064 System Operation 
CHAPTER 5 
SYSTEM OPERATING PROCEDURES 
SECTION I 
STATION OPERATION 
BASIC OPERATION 
CALLING 
l Press line key to select line. 
NOTE: Selecting a line is not necessary if: 
l A priority line has been assbned to a telephone (prjme hne feature enabled), l The telephone automaGcgl&fiFks gn idle line for 
use when the handset is llfte 
feature enabled). (idle hne preference 
l 
Listen for dial tone. 
l Dial number. 
When party answers, 
l Lift handset 
To end call, 
l Hang up...

IMI 66-064 System Operation 
NOTE: An autodial number can also be programmed as a 
secundary function at every DSS/BLF memory 
location. See Automatic Dialing instructions for 
de tails. 
To voice call a DSS number, 
l Lift handset. 
l Press softkey. 
l Voice announce. 
NOTE: When transferring a call, the outside line is auto- 
matically placed on hold when a DSS key is 
pressed. 
To tone call a DSS number, 
l Lift handset. 
l Press softkey. 
l Press ITCM. When intercom party answers, two-way...

Ii.4 66-064 System Operation 
FEATURE OPERATION 
REDIALING 
Last Number Redial 
The last number previously dialed can be redialed. 
l Press #. (If on line listening to dial tone, press HOLD 
w 
l Listen for ringing or busy tone. 
l Ringing tone: When party answers, pick up 
handset. 
l Busy tone: Press SPKR to disconnect. 
Automatic Redial 
The last number previously dialed can be redialed 
repeatedly. 
To program a softkey for automatic redial, 
l Press ITCM. 
l Dial~~l. 
l Press desired softkey. 
l...

IMI 66-064 
SYSTEM SPEED DIALING 
To dial numbers, System Operation 
l Press ITCM and dial paging code. 
HINTz Program a softkey with ITCMplus the paging 
l Press f. 
l Press desired ke 
locations 1 throug iY pad digits 01 - 30 for memory 
30. 
-OR- 
code to provide one-key access to paging. 
l Dial code for zone paging if required (refer to paging 
equipment instructrons). 
@ If on line listening to dial tone. 
l Press HOLD +Ic and then press desired keypad 
digits 01 - 30. 
VOICE ANNOUNCE BLOCKING 
To...

I’MI 66-064 System Operation 
l Press # at point in dialin 
sion to tone is required. sequence where conver- 
pulse dialing when call b 
is ystem will switch back to 
ended.) 
NOTE: Pulse/Tone switching can be programmed into 
softkeys by pressing # during number storage. 
MESSAGE WAITING 
The message waiting light, located above the HOLD 
key, is controlled by other stations in the system. The 
light will flash when a message for the station awaits 
pick up. 
To receive messages, 
l Press ITCM HOLD....