Comdial ExecuTech Model XE Key System Instructions Manual

Installation IMI 66-064 ’ 
SECTION 4 
INSTALLER/USER INFORMATION 
REGARDING FCC RULES AND REGULATIONS 
,: 
This electronic key system complies with Federal 
Communications Commission (FCC) Rules, Part 68. The 
FCC registration label on the KSU contains the FCC 
registration number, the ringer equivalence number, the 
model number, and the serial number or production date of 
the system. 
NOTIFICATION TO TELEPHONE COMPANY 
Unless a telephone operating company provides and installs 
the system, the...

IMi 66-064 
Programming Instructions 
CHAPTER 4 
SYSTEM PROGRAMMING 
SECTION 1 
INTRODUCTION 
System programming is divided into three areas of 
responsibility: 
l Class Of Service Programming: The class of 
service programming is unlimited as to the features 
that can be programmed using it. Class of service 
programming is usually performed by the installer 
when the system is first put in service. 
l Administration Programming: The administration 
programming can be used to program all system...

ITCM %# 746 + 
BASE LEVEL 
AUTO PAUSE TIME (750 Ms.ec/ZSec] 
TONENOICE 
EXCLUSIVE. HOLD 
CALL PICKUP  DENY TBL 1 
DENY TBL 2 
DENY TBL 3 
DENY TBL 4 
ALLOW TBL 1 
ALLOW TBL 2 
ALLOW TBL 3 
1 
ALLOW TBL 4 
ALLOW 1600 
(SPECIFY TABLE 
THEN DIAL UP TO 
8 DIGITS)  .5 
1.0 SEC 
1.5 SEC 
2.0 SEC 
3.0 SEC 
5.0 SEC 
7.5 SEC 
1OSEC 
15SEC 
20 SEC 62/38 
50/50 
70/30 10 PPS 
6x38 POPPS 
c 60 SEC 
SO SEC 
120 SEC 
160 SEC 
240 SEC 
300 SEC 
360 SEC 
420 SEC 
NEVER 
l-  SEE 
NUMBERING 
PLAN :EASTER ELEAR: : Press...

SNOUVIS ElHlO WVWOtld 01 
E&-OC 
L 
,r 
am 
3lOSN03 
XdO 
3,NV l-IV3 
3NllU 
3Nl;l8XE 1 
I I 
Ii 
013Nn 
6 3Nn 
9 3Nn 
L 3Nn 
9 3Nn 
s 3Nn 
P 3Nn 
c 3Nn 
z 3Nn 
1 3Nn 
I 
2 
013Nn 
6 3Nn 
9 3Nn 
L 3Nn 
9 3Nn 
s 3Nn 
v 3Nll 
9 3Nn 
2 3Eln 
1 3Nn  l-IO1 NDiSSV 
9NllVM 1lWl 
‘!+ 1MO11\1- 
NOU3WlS3tI 
-----G= d3Hd 3Nn 9fW 
(331EVN3 ‘r’d S3Nil= SV-1V 
a3N133a 3~ 01 013Nn 
6 3Nll 
6 3Nll 
L 3Nn 
9 3Nn 
s 3Nn 
P 3Nn 
6 3Eln 
z 3Nn 
1 3Ni-l 013Nn 6 3Nl-l 6 3NI-l 
L 3Nn 
9 3Nn 
s 3Nn 
P 3Nn 
9 3Nn 
z 3Nn 
1 3Nn...

Programming Instructions IMI 66-064 ’ 
SECTION 2 
CLASS OF SERVICE 
PROGRAMMING ,/ 
Class of service programming is usually performed by 
the system installer. Class of service programming 
procedures provide a means for programming all 
system variables. The installer may elect, however, to 
program only the line attributes and allow the 
remainder of the system variables to remain set to 
their default values. 
Perform class of service programming as follows: 
l Enter base level: ITCM % # 7 4 6 % 
0...

e 
cn 
Enter Base Level: Press ITCM, then dial +k # 7 4 6 *. 
Pause Time: During auto dials and 
speed dials it is sometimes necessary 
to delay the sending of digits to give 
switching equipment time to prepare to 
receive the digits. A pause can be 
stored to effect the delay. A pause is 
stored whenever the user presses the 
HOLD key. The pause length options 
are stored in seconds. 
Pulse Dial Time: Either ten or twenty 
pulses per second, and three different 
make/break ratios for the pulse dialing...

Flexible Toll Restriction: Restricts 
stations from dialing a range of number 
combinations while allowing specific 
exceptions. The restrictions are 
specified by entries on a deny table 
while the exceptions are specified by 
entries on an allow table. In addition, a 
pre-programmed 1+800 allow table 
allows that dialing feature regardless of 
Other restrictions which may be in 
effect. These programmed tables must 
be assigned on a per station basis 
before the restrictions can take effect. 
- Maximum...

4ssign restriction to lines: Lines 
nust be programmed to accept toll 
,estriction before the restriction that is 
Issigned to the stations will take effect. 
&sign restrictions to stations: 
station dialing can be restricted with 
I/O toll restriction and with deny/allow 
oil table restriction. Either one or both 
nethods can be assigned to restrict 
;tation dialing on a per station basis. 
Vso, 1+7-digit dialing can be allowed if 
I/O restriction is assigned. Dial 35. 
Press prog. keys to assign...

P 
a 
I Enter Base Level: Press ITCM, then dial & # 7 4 6 +#. 
I 
Automatic Pause Insertion: When the 
system stores a dialed number for later 
redial, it automatically stores a pause 
whenever the user waits between 
digits. The wait period is programmable. 
Tone or Voice Signalling: Intercom 
calls can be tone signalled or voice 
signalled. The first choice in signalling 
is programmable. 
Exclusive Hold: The user canset a 
hold condition whereby only the station 
placing the call on hold can retrieve...

Enter Base Level: Press ITCM, then dial J # 7 4 6 *. 
Line Disabled: A line can be taken out 
of service because of line defect or 
other reason. 
Auxiliary Line: A line can be 
conditioned to serve as a port for an 
external paging amplifier 
Line Type 1: A line port is assigned as 
type 1 when any enabled toil restriction 
is to be applied with the first digit 
dialed. Such a line type is often 
assigned when a CO line is connected. 
Line Type 2: A line port is assigned as 
type 2 when any enabled toil...