Comdial ExecuTech Model XE Key System Instructions Manual

Enter Base Level: Press ITCM, then dial #c # 7 4 6 +k. 
I 
Pulse/Tone Switchable: When rotary 
dial lines are installed, the user can 
switch from pulse (rotary dial signals) 
to tone (Dual Tone Multiple Frequency 
signals) for accessing special circuits 
requiting DTM.F tones such as banking 
machines. This pulse/tone switchability 
must be programmed for the line. 
Lines are defaulted for tone signalling 
2nly. 
Abandoned Hold Release: When a 
distant party abandons a hold condition 
and disconnects,...

I Enter Base Level: Press ITCM, then dial % # 7 4 6 %. 
I 
‘art Definition: A station port can be 
brogrammed to accept one of several 
lifferent types of station equipment or 
o support off-hook call announce 
:onnections. 
‘lexible Ringing Assignment: 
qinging assignments are 
)rogrammable on a per line/per station 
oasis. Delayed ringing can be program 
enabled for some lines and direct, or 
immediate, ringing can be program 
enabled for others. Iial61. 
3ial port ID (10-33). 
‘ress prog. key. 
1 Al =...

Enter Base Level: Press ITCM, then dial +lc # 7 4 6 %. 
I 
Night Transfer (of ringing): The day, 
or normal, ringing of incoming lines can 
be transferred to a particular station or 
stations by the attendant for off-hour or 
special purpose answering. Stations 
are assigned to receive night transfer 
by programming action. 
Access Denied: Access to particular 
lines can be denied at individual 
stations. 
Originating Denied: The ability to 
originate calls on certain lines can be 
denied at individual...

IMI‘F6-064 
Programming Instructions 
I  

Enter Base Level: Press ITCM, then dial C # 7 4 6 *. 
I 
Ml-Call and Zone Paging: Stations 
:an receive voice announcements 
hrough the telephone speaker, or 
hrough an external paging speaker 
:onnected to a PA port, and transmit 
hem with the telephone handset. 
Jnnouncements can be to certain 
areas of the system or to all stations in 
he system. 
Dersonal Ringing Tones: A station 
;an be programmed to ring in one of 
our distinctive tones. 
External Paging Interface - Station 
Port: A station port...

/ ” Base Level: Press ITCM, then dial % # 7 4 6 *. , 
very station can be assigned 
tdividually (mapped) to select any line l Dial port ID (10-33) 
ssigned to that station or to provide 
l Press station key 
ther key functions. Soft keys can be 
ssigned as direct station select (DSS) 
eys to provide one-key access to 
l Dial code for key per 
ystem stations. Soft keys can be 
ssigned as idle to provide autodial 
eys for the user. 
l Al-A5 = LINES l-5 
l A8-A12 = LINES 6-10 
l IO-33 = DSS STA. 
Press # +...

IMI 66-064 Programming Instructions 
SECTION 3 
SYSTEM ADMINISTRATION 
PROGRAMMING 
System administration programming is usually NOTE: A current program setting is indicated by a 
performed by on-site personnel. This programming lighted LED next to the applicable progamming 
procedure provide a means for programming all key. When a toggle (on/off) action is provided 
system variables, except line attributes, to match site by a single key, the lighted LED indicates when 
requirements. the feature is...

, Enter Base Level: Press ITCM, then dial k # 2 3 6 %. 
‘Pause Time: During. auto dials and 
‘speed dials it is sometimes necessary 
todelay the sending of digits to give 
switching equipment time to prepare to 
receive the digits. A pause can be 
stored to effect the delay. A pause is 
stored whenever the user presses the 
HOLD key. The pause length options 
are stored in seconds. 
Pulse Dial Time: Either ten or twenty 
pulses per second, and three different 
make/break ratios for the pulse dialing...

Enter Base Level: Press ITCM, then dial % # 2 3 6 ++. 
I 
Flexible Toll Restriction: Restricts 
stations from dialing a range of number 
combinations while allowing specific 
exceptions. The restrictions are 
specified by entries on a deny table 
while the exceptions are specified by 
entries on an allow table. In addition, a 
pre-programmed 1+800 allow table 
allows that dialing feature regardless of 
other restrictions which may be in 
effect. These programmed tables must 
be assigned on a per station...

[ 
E inter Base Level: Press ITCM, then dial %+ # 2 3 6 %. 
I 
issign restriction to lines: Lines 
nust be programmed to accept toll 
estriction before the restriction that is 
Issigned to the stations will take effect. 
&sign restrictions to stations: 
station dialing can be restricted with 
,/O toll restriction and with deny/allow 
oil table restriction. Either one or both 
nethods can be assigned to restrict 
;tation dialing on a per station basis. 
Use, 1+7-digit dialing can be allowed if 
/O...