Comdial Executech 2264X, 2296x Hybrid System Installation Manual

IMI 66-060OVERLAY: 703500-566Programming
OVERLAY: 703804456
00000000000000000000000000000000000000
000000000000000000000000Figure 
3-1.OVERLAY: 703500-566
OVERLAY: 703804-275OVERLAY: 703500467
c
t-mm-----
“v”uuLJ”u
E%%%%%eE%%%%%e
0000000000000000
0000000000000000
0000000000000000J
Programming Overlay Identif
:ation
3-5 

IMI 66-060
Programming
SYSTEM COS PROGRAMMING PROCEDURE
-----------------------------------------------------------------
SYSTEM DEFAULTS.
Recall/flash time = 2 seconds
. Pause time 
- 1 second.
. Timed Hold recall time 
= 60 seconds
. Printer baud rate 
- 1200 baud, 7-bit data
. Intercom first choice 
signalling = voice first
. Printout line length 
= 80 Columns
. Central message desk 
= not assigned
. Unanswered call transfer 
- 20 seconds
. Port Assignments: Station 10 
- LCD Speakerphone
All other...

IMI 66-060Programming
4.Set tired holdrecall time.
. Press programkey C36..
. Press keypad key for time.
l- 30 SEC.6 - 240 SEC.
2- 60 SEC.7 - 300 SEC.
31 90 SEC.8 - 360 SEC.
41 120 SEC.9 T 420 SEC.
5- 180 SEC.0 - DISABLED
-. Press l .
5a. Set the baud rate of data printout.
. Press program key C39 (or dial 6 from keypad)
. Set baud rate with keypad.
l-110BAUD,7BITS
2-150BAUD,7BITS
3-300BAUD,7BITS
41600BAUD,7BITS
5-1200BAUD,7BITS
612400BAUD,7BITS
7-3600BAUD,7BITS
8-4800BAUD.7BITS
9 -9600BAUD,7BITS
0...

IMI 66-060
Programming
8.Set unanswered call transfer recall time.
. Press program key C33.
. Press keypad keys for time.
2: 120SEC. 10 SEC.6 7= =60 90SEC. SEC.
3 =25 SEC.8 =120SEC.
4 =30 SEC.9 =180SEC.
5 =45 SEC.0 =240SEC.
. Press l .
9.Specify station type for each station port.
l Dial port number of station from keypad beginning at any desired
active port.
.Dial 010 -073 for model K2264
. Dial 010 
-105 for model K2296
. Press console key to specify station type.Cl8 
=32-Key Console without call...

IMI 66-060Programming
. 11.Select baud rate of tape data if tape storage of COS data is
planned.
. Press program key C38.
. Press RECALL for 100 baud.
-OR-
. Press  SAVE for 50 baud.
12.Press l .
13.Press MOBITOB to exit or proceed to next COS requirement.
3-9 

IMI 66-060
TOLL RESTRICTION PROGRAMMINGProgramming
-----------------------------------------------------------------
SYSTEM DEFAULTS
Toll restriction tables 1 and 2 have entries defaulted in them.
These
tables are assigned to all lines.
They can be unassigned by line COS
programming or reprogrammed with different entries per the following
procedure.
In order for toll restriction to take effect,the following three-fold
process must 
occur*
.One or more toll tables must be entered
.Toll tables must be...

IMI 66-060Programming
5.Select table entry from chart with program key.
6.Dial number to be restricted (16 digits maximum).Press f for
match anything digit.
7.Repeat steps 5 and 6 until all numbers are programmed in table.
8.Repeat steps 3 through 7 until all tables are programmed.9.
Press l .
10. Press HOIITOB to exit or proceed to next COS programming step.
3-11 

IMI 66-060
Programming
LINECOS PROGRAMMING
--------------------________II__________-------------------------
LINE DEFAULTS
. Line type = TELCO
. Line groups
= none assigned
. Dial Mode 
= DTMF
. Privacy status = private
. Toll Tables 
=1 and 2 assigned
. Abandoned Hold Timeout 
= 50 msec.
-----------------------------------------------------------------
PROGRAMMING
NOTE:Before performing this procedure, turn to the Line COS
Programming Reference Chart located at the end of this chapter, and
enter the...

IMI 66-060Programming
6.Select privacy rode.
. Private = C28
. Non-private = C297.
Assign toll tables.
I4
t 5
I Cl3 I ~12-----c21
6I 
ClA I l?
Iii;111;Ic22 C23 27
ICl6I15C24.
8.Set abandoned hold timeout period.
. 300 milliseconds - C30
. 50 milliseconds = C31
9.Repeat steps 2- 8 for each line.
10. Press l .
11. Press MONITOR to exit or proceed to next COS programming
requirement.3-13 

IMI 66-060
STATION COS 
PBOGBAHMIBGProgramming
----------------------------------------------------------------
STATION DEFAULTS
. PA port= disabled
. Voice announce block 
= disabled
. Executive override = disabled
. System speed dial toll restriction = disabled
. Personal ringing tone 
= tone 1
. OPX through-dialing 
= disabled
. Automatic hold 
= disabled
. Message wait originate 
= disabled
.Prime line/group = none
. Ringing line preference 
= disabled
. Direct ringing
- all lines ring on stations...