Comdial Executech 2264X, 2296x Hybrid System Installation Manual

COMDIAL.
ExecuTech
el2264X and 2296X Hybrid Systems
l Installation
l Programming
l Maintenance
I1
This publication is applicable to the following common equipment :
- Model K2264 Mfg. Code 8xxH or later
- Model K2296 Mfg. Code 8xxH or later
lM166-060.01
1268Change pages 3-14,3-38,3-39 i%g 

IMI 66-060
TABLE OF CONTENTSTable Of Contents
CHAPTER 1 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l- 1
MANUAL SCOPE..................................................l-l
RELATED PUBLICATIONS..........................................l-l
GENERAL INFORMATION...........................................l-2
INSTALLER/USER INFORMATION
REGARDING FCC RULES AND REGULATIONS...........................
l-2
RINGER EQUIVALENCE...

IMI 66-060 Table Of Contents
Table Of Contents 
- continued
LIST OF ILLUSTRATIONS
Figure
2-l.KSU Mounting Dimensions ..........................2-2
Figure2-2.32-Button Adjunct Feature Module Wiring.........2-2
 3
Figure2-3.Common Audible/Auxiliary Station  Interface......2-2 4
Figure
2-4.PA Connections .................................. 2-24
Figure
2-Sa. Common Equipment Connections...................2-2  5
Figure
2-5b.Auxiliary Equipment Interconnection............2-2  6
Figure
2-5~.Station Equipment...

IMI 66-060Introduction
CHAPTER 1
IBTBODUCTIOB
HARUAL  SCOPE
This publication contains  
installation,.programming,  and maintenance
information for the Model K2264 and  K2296  hybrid systems and the
associated equipment.
This manual is applicable to systems marked with a manufacturing code
of 
8xxH and later.
The system is fully protected,and therefore the installation does not
require the services of an authorized agent. However, the
installation procedures detailed in this manual should only be...

IMI 66-060
Introduction
IBSIALLEB/USEB INPOP~AIION
REGARDING FCC RULES AND REGULATIONS
This electronic key system complies with Federal Communications
Commission (FCC) Rules, Part 68.
The FCC registration label on the KSU contains the FCC registration
number,the ringer equivalence number, the model number, and the
serial.number or production date of the system.
Botiflcation To Telephone Company
Unless a telephone operating company provides and installs the system,
the telephone operating company which...

IMI 66-060
Introduction
. Installation Requirements
Connection of the electronic key system 
to the telephone lines must be
thr.ough a universal service order code (USOC) outlet jack supplied by
the telephone operating 
company+If the installation site does not
have the proper outlet,ask the telephone company business office to
install one.The correct outlet jack for this system is a type 
RJ21X.
SParty Lines And Coin Lines
Local 
te1ephon.e company regulations may not permit connections to
party lines...

IMI 66-060Introduction
If necessary, the user should consult the manufacturer or an
experienced radio/television technician for additional suggestions.
The user may find the following booklet prepared by the Federal
Communications Commission helpful: How to Identify and Resolve
Radio-TV Interference Problems. This booklet is available from the
Government Printing Office, Washington D.C.
20402. Stock No.
004-000-00345-4.
Ringer Bquivalence Number
The REN of each line is 
0.4B. The FCC requires
 the...

IMI 66-060
Installation
CHAPTER 2
INSTALLATION
MOUNTING CONSIDERATIONS
. The common equipment and power supply cabinets should be attached
vertically to any sturdy, flat, surface.They may be vertically
rack mounted if desired.
. The power supply cabinet can be mounted so that the power connector
and fuses are facing either toward the right side or toward the left
side of the mounting Location.
. The power interconnection cable is four feet in length.Locate the
cabinets with respect to each other so that...

IMI 66-060Installation
.  MOUNTING  PROCEDURE
I.Unpack, and carefully inspect the common equipment, power supply
and stations for shipping damage.
any damages found. Notify the shipper immediately of
Verify  that the packages contain all parts  and
accessories needed for proper installation and operation.
2.If a backboard is required at the mounting location, attach it
securely to provide a stable mounting surface for the equipment.
3.A full scale mounting template is supplied.
the mounting surface,Hold...

IMI 66-060Installation
Figure 2-l.Mounting Dimensions
2-3