Comdial Executech 2264X, 2296x Hybrid System Installation Manual

DEDICATED II’IVAC15 AMP NEMA 5-1’3ELECTRICAL OUTLET
WITH THIRD-WIRE OROUND
TO CORNECTOI? BLOC& J-5*,-I e-n”,,v ,w.NECTORBLOC
TO CONNECTORNOTES 
8I. TO HELP INSURE THAT FOREION VOLTAQESDO NOT DAMAGE THE SYSTEM VERIFY THAT
QAS DISCHAAOE TUBES OR Slf4lLAR PROTECTION
DEVICES ARE INSTALLED AND PROPERLY
GROUNDED. IN ALL 
CONNltCTED TELCO LINES.
2. 
SROUND ALL UNUSED CONDUCTORS IR CABLE RUNS
TO REDUCE POTENTIAL FOR NOISE ON LINES.
TO CORRECTOR BLOCK J
TO CONNECTOR BL
TO CORNECTOR
Figure 2-5a.Common Equipment...

I NUJSTRY STANMADMmlnAl LIME CcmI4-CONOUCTCRI
i
II PROTECTIVE QRoum LEAD
I
1 a.lP TmulNAl.B
IWXIWM DlsTu(cE EMEN KSU ANDPt?lNlER IS LlWlED TO 500 FEET. SIRN’RTS TO CT!5 AT CONNECTOR EUCK J-4 IF2NOT RaJlllED BY PRINTER.)o)Figure 
2-5b.Auxiliary Equipment Interconnection - Typical
Connections 

NOTES II. TYPE 66M-XX CONNECTOR BLOCK SHOWN
AS TYPICAL- OTHER TYPES MAY BE USED
AS DESIRED.
2. ALL STATION CABLE IS TWISTED PAIR
FROM STATION JACK TO CONNECTOR BLOCK.ATTENOANT STATION 
IOl&J30 PROGRAYMINO STATIONITYPICAL
WORK STATION
WITH CALL ANNOUNCE
ADJUNCT FEATURE 
MODULETYPICAL STATION
CONKECTOR BLOCUtJl SHOwW FOR IUUSTRATIOMJFigure 
2-5~.Station Equipment Interconnection - Typical Connections 

IMIInstallationMCcl
2-27 

IMI 66-060
InstallationSYSTEM CHECKOUT
Initial Condition
The system operating features are set to default conditions
at initial power up.These conditions provide a basic operating
system with a known 
set.of parameters,
and the system should be
initially checked out with the default conditions in place. At
anytime while the system is operating,
default conditions can be reset
from station port 10 or 11 per the instructions provided in Chapter 3.
Check Out
Check the common equipment and telephone...

IMI 66-060
InstallationVoltage Check
Make the following voltage measurements at the station connector
blocks under the following conditions:
. Bridging clips installed
. 
AC power connected to the common equipment
Measure the voltage across one voice line and one data line and then
across the other voice line and the other data line for each even and
odd station.The measured voltage must be as follows:
METER LEADMEASURED
CONNECTION
POLARITYVOLTAGE
YPICAL EVENVoice 1
(+ISTATIONData 3C-1+33 +/- 5 VDC...

IMI 66-060
Programming
CHAPTER 3
SYSTEM PROGRAHNING
GENERAL INFORMATION
Class Of Service (COS) programming consists of the following major
categories:
. General System COS
.Toll Table Entry
. Line COS
. Station COS
.COS programming is performed from the attendant station
.Executech II multiline telephone installed at station port 10 or
11 and a companion DSS/BLF Console or Adjunct Feature Module
installed at console port 10 or 11 respectively.No other type of
Executech 
keyset can be used for programming...

IMI 66-060Programming
IMPORTANT NOTE: The COS values that are recorded from an an older
model K2264 revision A through H cannot be re-loaded into any model
K2264 with a later revision or manufacturing code.
Doing so, will
cause the newer model K2264 common equipment to enter a lock-out
condition which will prevent any further manual COS programming  of
it and which can only be cleared by disconnecting AC power from the
equipment for a period of at least 48 hours. Access to COS
programming via a VDT...

IMI 66-060
Programming
Hybrid Configuration
The Single-line 
keyset is a prime intercom station, however; access to
outside lines is made available through COS programming.
To receive outside calls on a Single-line 
keyset,
. The call must be answered at a multiline station and extended to
the Single-line 
keyset through the use of the call transfer
feature.
. Alternately,the Single-Line 
keyset station port can be programmed
to have the ringing line preference feature, and to have ringing
enabled on all...

IMI 66-060
ProgrammingCLASS OF SERVICE DEFAULT
The system can be defaulted to a standard class of service per the
following procedure.
The default conditions are listed at the
beginning of each COS programming procedure and shaded on the
programming reference charts.
1.PressITCHl 7 4 6 l .
2.Press program key C38.
3.Press keypad key(s) to choose default settings.
1System COS and CENTREX COS default
2Line COS default
3Station COS default
4Pulse dialing - all lines
5Tone dialing - all lines
6Flexible...