Comdial Executech 2264X, 2296x Hybrid System Installation Manual

IMI 66-060Programming
IMPORTANT NOTE:The COS values that are recorded from an an older
model K2264 revision A through H cannot be re-loaded into any model
K2264 with a later revision or manufacturing code.
Doing so, will
cause the newer model K2264 common equipment to enter a lock-out
condition which will prevent any further manual COS programming of
it and which can only be cleared by disconnecting AC power from the
equipment for a period of at least 48 hours.Access to COS
programming via a VDT Terminal...

IMI 66-060
Programming
VEBIFIBG TAPE DATA (Requires Data Printer)
To verify previously recorded cassette tape,
. Rewind pre-recorded cassette tape, and prepare recorder.
for play-back.
. PressITCM * 7 4 6 * ITCH.
. Start tape playback.
. Press program key C39.
. Printer will print status as follows:
VERIFY COS DATA TAPE
VERIFY TAPE DATA COMPLETE
VERIFY TAPE DATA ERROR
LOADING COS DATA FROM TAPE
To load previously recorded COS program values into system to replace
current program values, proceed as...

IMI 66-060
SYSTEM CLOCK 
INFORNATIONProgramming
All clock setting and adjustment must be performed from station port
10 or 11.
SETTING THE CLOCK
1.Press ITCM,then dial * #.
2.Dial the clock date with the key pad keys.
YEAR MONTH DAY HOUR MINUTE
xxxxxx xxxx
NOTE: Values less than 10 must be dialed as OX, and hours must be
expressed in the 24-hour format.
3.If the SMDR printer is installed and operating, the clock date
will be printed as follows.
.* 01/08/86 16:00 (Example)
4.Reset the minutes setting, if...

IMI 66-060
Programming
SYSTEM SPEED DIAL 
PROGBAWING
Fifty (50) system speed dial numbers can be stored from station port
10 or 11 for use at all stations in the system.
System speed dial
numbers will not be toll 
res,tricted unless specified by station COS
programming.
To store speed dial numbers,
. Press ITCM l .
. Perform the following steps:
. Press SAVE.
. Dial storage location (10 
- 59) from keypad.
. Choose line or group preselection (multifunction (hybrid) system
only by dialing 1 
-4 from...

bo0kP4
i
E-
fimIm 

IMI 66-060
K/ PFtOORAM EN-IRYProgramming
UNE 
CO9STA’IION CO9PRlNl’OUl. . 
STATICM CDS cFFb&TSPA Pa(T:DISnBEO
VOICE R.ocK:DIs.AamEXEWTIYE ovERlE:DIyBEDAUTOUTIC HxD=oISAELalYsutE WAIT CRIGINA~:DI~RING TOIIE=TCM !F?tlY LlNE&RCW:Na(E
RINGING LINE RmDWa:DlyaEDSrsTw SpEm DlrV TU. RESlRICTlaU:DIUBEO
~,@.@~3’RlNG lWE 122 LINE KEYSET ONLY,SELECT R)IUi LINE:~:LINE:oRtm m @%~,@Q,@?ddNK GRUPS I -4
e)FLII RlWlNG LINE RQ.
@NI~TTRU(SFD( -=T FEATLF(E
SELECT LINES wITi+(PLECTICN CWMT KE,$
~ASSIGW lCU T1Blf:- ITol...

IMI 66-060
Programming
SYSTEM COS PROGRAMMING REFERENCE TABLE
4
6
%
. Shading denotes system default conditions.
. Check off the values chosen for the system being programmed.
To enter base level:ITCH 
* 7 4 6 *
3
t6240 SEC.
7300 SEC.
8360 SEC.
9420 SEC.
0DISABLED
Note: A 0 program selection (disabled)
makes 
it possible for an exclusive hold
condition, when set at a station, to placea line in a hold state that cannot be
released at any other station.
~ijiiijxii~:~:i~~~;~. . . . . . . ...; . . . . . . ....

IMI 66-0609ASSIGNMENT OF STATION TYPES
,STATION TYPEIProgramming
C24EXECUTECH II MULTILINE TELEPHONE
077
078
079
080061
10 1 Cl 0 ASSIGN CONSOLE PAIRS TO CONSOLE PORT PAIRS
PORT/KEYAB
KEY
lO/CiOl II/C11i 42lC12 1 43lCl3
3-32 

IMI 66-060ProgrammingTOLL RESTRICTION PBOGRAHHING REFERENCE TABLESTABLE ENTRY PROCEDURE
1. Determine the types of dialing restrictions which must be imposed on the system. Typically,
this includes access codes which result in toll charges, and certain local numbers as desired.
2. If the restricted dialing codes will be imposed consistently on most or all stations in the sys-
tem, list them on one or two tables. If wide variation in the dialing restrictions is planned,
spread the listing out across...

IMI 66-060ProgrammingTOLL RESTRICTION PROGRAMMING REFERENCE TABLES. Tables 1 and 2 defaulted as shown.
TOLL RESTFilCTlON TABLE1
TYPE: ALLOWDENYY__
ENTRYENTRY NUMBER (16 MAXIMUM)1 2 3 4 5 6 7 8 9 10 12 
1311 14 1516
1illllllllllllllll2976
I34 11A‘.1I1 I I I I I I I I II I I I ITABLE AiSIGNMENT: UNES ALL STATIONS
TABLE ASSIGNMENT: UNES ALL STATIONSI
1 TOLL RESTRICTION TABLE6
=* ALLOW-.DENY‘Typ
ENTRYENTRY NUMBER (16 MAXIMUM)
111213141516(71819IlOll12113114(15116I I
II
TOLL RESTRICTION TABLE7ITYPE:...