Comdial Executech 2264X, 2296x Hybrid System Installation Manual

IMI 66-060Programming
3.Dial port number of station port to be programmed.
4.To default the following features, if desired, press SAVE.
. PA port disabled
.Prime line not assigned
. Voice blocking disabled
. Executive override disabled
. Message wait-originate disabled
. Automatic hold disabled
. System speed dial toll restriction disabled
. Ringing line preference disabled
. Hunt groups disabled
5.Enable PA port.No further programming at this port number is
required if a PA port is enabled.
. Press...

IMI 66-060Programming
Table 3-1.Program Keys For Line And Group Choices
14.Enable ringing line preference.
. Press C40.
15.Select ringing assignments for lines active at station.
RINGING
.Press Cl8 (clears previous settings).
. Press program key(s) per Table 3-1 to choose lines.DELAYED RINGING
. Press Cl9 (clears previous settings).
. Press program key(s) per Table 3-1 to choose lines.
16.Select night transfer (of ringing) for certain lines.
. Press C20 (clears previous settings).
. Press program key(s)...

IMI 66-060
Programming
21.Assign toll tables to station.
.Press C25 to clear all toll tables assigned (if
desired)..
. Specify toll tables with program keys as follows:
PROGRAM KEY Cl0 Cl1 Cl2 Cl3 Cl4 Cl5 Cl6 Cl7
TOLL TABLE
12345678
PROGRAM KEY Cl8 Cl9 C20 C21 C22 C23 C24 C25
TOLL TABLE
910111213141516
22.Reserve an intercom link.
. Press RECALL.
Press keypad key l-7 to reserve link l-7.
IOR-
.Press 0 key for no reserved link.
23.Select all-call and/or zone paging configurations.. Press 
#.
.Disable all...

IMI 66-060Programming
FOR Executech II multiline telephone:
.Press C39.To assign line appearance to keys,
.Press key to be assigned (A or B field).Fast tone bursts
sound.
.Press program key per Table 3-l to choose line-
Tone bursts stop.
- ..Repeat for all keys requiring line appearance.
To disable line appearance at keys (clears any prior assignment),
.Press key to be denied appearance.Fast tone bursts sound.
. Press RECALL key.Tone bursts stop.
.Repeat procedure for all required key locations.
To...

IMI 66-060
Programming
BLOCK PROGRAMMING OF STATION COS
Block program a group of stations with a previously programmed class
of
1.
2.
3.
4.
service.
Enter base level : ITCH l 7 4 6 *.
Press HOLD.
Dial station port number (from keypad) to identify model station.
Dial station port number (from keypad) to specify first station in
block.
5.Dial station port number (from keypad) to specify last station in
block.
6.Press* MONITOR to exit programming.
NOTE:Flexible key/function assignments for station port 010...

IMI 66-060
Programming
A particular station can be linked at the end of 
more than one hunt
group so long as the sixteen station ports per group are not exceeded.
For instance,a second terminal hunt group could be formed along with
the example shown above:
. Station port 020 is linked to station port 021
. Station port 021 is linked to station port 
022
. Station port 022 is linked to station port 016.
Thus,station port 016 would serve in both terminal hunt groups
although the groups are independent...

IMI 66-060Programming
BUNT GROUP PBOGRAHHIBG
To program two station ports into a hunt group, . Press 
ITCM  l 7 4 6 * (enter base level programming mode).
. Enter station COS programming: . Press 
C41.
. Choose first station in link: . Dial station port 
number(OlO-105).
. Enter linking mode:. Press 
C30.
. Choose second station in link: . Dial station port number (010-105).
. Establish link: . Automatic linking occurs  
- no action required.
. Press 
* (return to base level).
To add additional station...

IMI 66-060Programming
COS AND 
SMDB PRINTOUT
COS PRINTOUT
When a data printer is connected to the system, it can be commanded,
from station port 10 or 11,to print the class of service 
(COS)
programming configuration.Partial or complete printouts can be
obtained.
When the printer is being used to obtain a COS printout,
the Station Message Detail Recording (SMDR) function is temporarily
halted.SMDR data collection is continued by the system during a COS
printout operation; however,if more than two calls...

IMI 66-060Programming
/STATION NUMBER
MONTH/DAY/YEAR
CALL DURATION TIME-MINUTES. TENTHS
IF GREATER THAN 9.9, PRINTS ‘???“)I CARRIAGE RETURN I1 CARRIAGE 
RETURNJDIALED DIGITS-UP TO MAXIMUM OF 32
(ACCOUNT CODES ARE ISOLATED BY l OR 
# SYMBOLS
NOTES
1.CARRIAGE RETURN AND LINE FEED IMMEDIATELY
FOLLOW LAST PRINTED CHARACTER ON EACH
LINE. ALSO SEE NOTE 2.
2.lLLUSTRATEDPRlNTOUTIS4OCOLUMN,TWO-LINEFORMAT. FOR 80 COLUMN ONE-LINE PRINTOUT
FORMAT, CARRIAGE RETURN AND LINE FEED
CHARACTERS AT END OF LINE 1 ARE...

IMI 66-060
CASSETTE TAPE RECORD OF COS VALUESProgramming
GENERAL INFORMATION
. Connect the audio cassette taperecorder microphone connector to the
music interface jack on the side of the 
KSU.
. Do not perform any other programming action while the tape system is
active.
.Program the baud rate of the tape data to be either 100 or 50 baud
as desired. (See System COS for programming details.)
. If the system includes a data printer,appropriate response and
error messages will be printed during the...