Comdial Executech 2264X, 2296x Hybrid System Installation Manual

							IMI 66-060OVERLAY: 703500-566Programming
OVERLAY: 703804456
00000000000000000000000000000000000000
000000000000000000000000Figure 
3-1.OVERLAY: 703500-566
OVERLAY: 703804-275OVERLAY: 703500467
c
t-mm-----
“v”uuLJ”u
E%%%%%eE%%%%%e
0000000000000000
0000000000000000
0000000000000000J
Programming Overlay Identif
:ation
3-5 
						

							IMI 66-060
Programming
SYSTEM COS PROGRAMMING PROCEDURE
-----------------------------------------------------------------
SYSTEM DEFAULTS.
Recall/flash time = 2 seconds
. Pause time 
- 1 second.
. Timed Hold recall time 
= 60 seconds
. Printer baud rate 
- 1200 baud, 7-bit data
. Intercom first choice 
signalling = voice first
. Printout line length 
= 80 Columns
. Central message desk 
= not assigned
. Unanswered call transfer 
- 20 seconds
. Port Assignments: Station 10 
- LCD Speakerphone
All other station ports
= Executech II multiline telephoneConsole port 
10a and lob -70-Key and 32-Key consolesAll other console ports 
= 40-Key consoles
. Tape baud rate - 100
-----------------------------------------------------------------
PROGRAMHING
NOTE:Before performing this procedure,turn to the System COS
Programming Reference Chart located at the end of the chapter, and
enter all system requirements on the charts for reference.
1.PressITCH l7 4 6 l(base level entry if not active)
2.Set recall/flash time.
.Press program key C34.
. Press keypad key for time.1 
- 80MSEC.6=875MSEC.
2- 300MSEC.7=1.0SEC.
3= 500MSEC.8=1.5SEC.
4- 600MSEC.92.0SEC.
5- 750MSEC.03.0SEC.
.Press+.
3.
Set pause time.
.Press program key C35.
. Press keypad key for time.
l=.5SEC.6=5.0SEC.
2=1.0SEC.7-7.5SEC.
3-1.5SEC.8=10.0SEC.
4-2.0SEC.9=15.0SEC.5 
-3.0SEC.0=20.0SEC.
.Pressl.
3-6 
						

							IMI 66-060Programming
4.Set tired holdrecall time.
. Press programkey C36..
. Press keypad key for time.
l- 30 SEC.6 - 240 SEC.
2- 60 SEC.7 - 300 SEC.
31 90 SEC.8 - 360 SEC.
41 120 SEC.9 T 420 SEC.
5- 180 SEC.0 - DISABLED
-. Press l .
5a. Set the baud rate of data printout.
. Press program key C39 (or dial 6 from keypad)
. Set baud rate with keypad.
l-110BAUD,7BITS
2-150BAUD,7BITS
3-300BAUD,7BITS
41600BAUD,7BITS
5-1200BAUD,7BITS
612400BAUD,7BITS
7-3600BAUD,7BITS
8-4800BAUD.7BITS
9 -9600BAUD,7BITS
0 -19200BAUD,7BITS
.Press*.
5b. Set line length of data printout.
6.
7.
.Press program key C38.
. Set linelength with keypad.
# =One 80 column line
8=Two 40 column lines
. Press 
*.
Choose intercom first choice signalling.
. Press RECALL for voice.
. press SAVE for tone.
. Press l .Specify central message desk (one per system allowed).
.Press i.
. Dial port number from keypad.
. Press 
*.
3-7 
						

							IMI 66-060
Programming
8.Set unanswered call transfer recall time.
. Press program key C33.
. Press keypad keys for time.
2: 120SEC. 10 SEC.6 7= =60 90SEC. SEC.
3 =25 SEC.8 =120SEC.
4 =30 SEC.9 =180SEC.
5 =45 SEC.0 =240SEC.
. Press l .
9.Specify station type for each station port.
l Dial port number of station from keypad beginning at any desired
active port.
.Dial 010 -073 for model K2264
. Dial 010 
-105 for model K2296
. Press console key to specify station type.Cl8 
=32-Key Console without call announceCl9 =
32-Key Console with call announce
c20 =LCD Speakerphone
c22 =Single-line keyset (hotel phone)
C23 
=3 and 8 Line Keyset
C24 
=Executech II multiline telephone
C25 
=Single-line keyset (administrative phone)
C25 
=Port to be used for connecting OPX accessory unit
. Press *and repeat steps for each remaining active station port.
NOTE:This step 9 action setsthe identified port to the default
conditions for that specified station type.
Also,station port 010
can only be changed to an Executech II multiline telephone from the
default assignment as an LCD Speakerphone.10.Specify console type for each console port pair.
. Press program key Cl0 to enable port pair selection.
. Press program key to specify console port pair.. 
Cl0 =10a and 10b. 
Cl1 =lla and lib. 
Cl2 =42a and 42
.Cl3 =43a and 43
.Press program key to specify console types.
. 
Cl0a port= 70-Key console; b port = 32-Key console. 
Cl1a port= 70-Key console; b port = 40-Key console. 
Cl2a port= 70-Key console; b port = 70-Key console. 
Cl3a port= 40-Key console; b port = 32-Key console
.Cl4a port= 40-Key console; b port = 40-Key console
.Cl5a port= 32-Key console; b port = 32-Key console
.Repeat port and console selection steps for all required ports.
3-8 
						

							IMI 66-060Programming
. 11.Select baud rate of tape data if tape storage of COS data is
planned.
. Press program key C38.
. Press RECALL for 100 baud.
-OR-
. Press  SAVE for 50 baud.
12.Press l .
13.Press MOBITOB to exit or proceed to next COS requirement.
3-9 
						

							IMI 66-060
TOLL RESTRICTION PROGRAMMINGProgramming
-----------------------------------------------------------------
SYSTEM DEFAULTS
Toll restriction tables 1 and 2 have entries defaulted in them.
These
tables are assigned to all lines.
They can be unassigned by line COS
programming or reprogrammed with different entries per the following
procedure.
In order for toll restriction to take effect,the following three-fold
process must 
occur*
.One or more toll tables must be entered
.Toll tables must be assigned to all appropriate lines.
.Toll tables must be assigned to all appropriate stations.
Only the toll tables(s) which are entered and assigned to both a line
and a station using that line will invoke any toll restriction.
PROGRAMMING
NOTE:Before performing this procedure, turn to the Toll Restriction
Programming ReferenceTables located at the end of this chapter, refer
to the chart entry instructions included there, and enter all toll 

restriction requirements on the charts for reference.
1.Press ITCM * 7 4 6 * (base level entry if not active).
2.Press program key C37 (enter toll program mode).
3.Select table number from chart with program key.
rTABLENUMBER1234567-8
PROGRAM KEYCl0 Cl1 Cl2 Cl3 Cl4 Cl5 Cl6 Cl7
TABLENUMBER910111213141516
PROGRAM KEYCl8 Cl9 C20 C21 C22 C23 C24 C25
4.Select table type with program key.
Deny table = C38
Allow table = C39
3-10 
						

							IMI 66-060Programming
5.Select table entry from chart with program key.
6.Dial number to be restricted (16 digits maximum).Press f for
match anything digit.
7.Repeat steps 5 and 6 until all numbers are programmed in table.
8.Repeat steps 3 through 7 until all tables are programmed.9.
Press l .
10. Press HOIITOB to exit or proceed to next COS programming step.
3-11 
						

							IMI 66-060
Programming
LINECOS PROGRAMMING
--------------------________II__________-------------------------
LINE DEFAULTS
. Line type = TELCO
. Line groups
= none assigned
. Dial Mode 
= DTMF
. Privacy status = private
. Toll Tables 
=1 and 2 assigned
. Abandoned Hold Timeout 
= 50 msec.
-----------------------------------------------------------------
PROGRAMMING
NOTE:Before performing this procedure, turn to the Line COS
Programming Reference Chart located at the end of this chapter, and
enter the line requirements for each line to be programmed.
1.
2.
3.
4.
5.PressITCM* 7 4 6 * (base level entry if not now active)
Select line to be programmed.
Select line type.
. Disabled = C38
. Auxiliary = C39
.CO/PBX = C40
Select line group (multifunction configurations only).
.No group assigned = C41
.Group 1 = C34
.Group 2 = C35
.Group 3 = C36
.Group 4 = C37
Select dialing mode.
.Pulse/tone = C26
.Tone only= C27
3-12 
						

							IMI 66-060Programming
6.Select privacy rode.
. Private = C28
. Non-private = C297.
Assign toll tables.
I4
t 5
I Cl3 I ~12-----c21
6I 
ClA I l?
Iii;111;Ic22 C23 27
ICl6I15C24.
8.Set abandoned hold timeout period.
. 300 milliseconds - C30
. 50 milliseconds = C31
9.Repeat steps 2- 8 for each line.
10. Press l .
11. Press MONITOR to exit or proceed to next COS programming
requirement.3-13 
						

							IMI 66-060
STATION COS 
PBOGBAHMIBGProgramming
----------------------------------------------------------------
STATION DEFAULTS
. PA port= disabled
. Voice announce block 
= disabled
. Executive override = disabled
. System speed dial toll restriction = disabled
. Personal ringing tone 
= tone 1
. OPX through-dialing 
= disabled
. Automatic hold 
= disabled
. Message wait originate 
= disabled
.Prime line/group = none
. Ringing line preference 
= disabled
. Direct ringing
- all lines ring on stations 10; 17; 39; and 41
. Delayed ringing = none
. Night transfer (of ringing) 
=all lines ring on stations 10, 17, 39
and 41
. Privacy status = private
. Line access denied 
= none
. Call origination denied 
= none
. Idle line preference 
= none
. Toll tables = none assigned
. Reserved intercom link 
= none
. All-call receive 
= enabled
. All-call originate 
= enabled
. Zone page receive = disabled
. Zone page originate = disabled
. Hunt group = disabled
.Line/key assignment 3 and 8 Line Keyset:. 
B=Field keys (Bl=B8) = lines 1=8
.Line/key assignment Executech II multiline telephone:
. Single Line 
Keyset accesses intercom line only
-----------------------------------------------------------------
PBOGRAWfIIG
NOTE:Before performing this procedure, turn to the Station COS
Programming Reference 
Chart.located at the end of this chapter, and
enter the station requirements for each station to be programmed.
. Perform all steps in sequence.
.Skip those steps not required.
1.
PressITCM l 7 4 6* (base level entry).
I
2PressprogramC41 (programentry).
Change page ?I89
3-14