Home > Comdial > Communications System > Comdial Executech 2000 Instructions Manual

Comdial Executech 2000 Instructions Manual

Here you can view all the pages of manual Comdial Executech 2000 Instructions Manual. The Comdial manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 41

Call Override Features (continued) 
Service Observing 
For training purposes, this feature allows you, undetected, to 
monitor a conversation at another station. 
To monitor an in-progress call: 
1. While on-hook, press @a@@. 
2. Dial extension number of station you are going to monitor. 
3. Press SPKR to end. 
0 
Call Waiting 
You can send a call waiting tone to a busy station and wait for an 
answer. 
To activate call waiting: 
1. Make intercom call and hear busy signal. 
2. Dial a @a. Called party...

Page 42

Display Contrast Adjustment 
If your telephone has an LCD, you can adjust the contrast of the 
display by holding down the MUTE button on your telephone. 
After five seconds, “Contrast Level” and a number shows up in 
the display. Continue holding down the MUTE button; the display 
contrast changes. 
The numbers 0 through 7 represent the display contrast from light, 
or 0, to dark, or 7. 
When you have adjusted the display contrast to suit you, release 
the MUTE button. 
NOTE: For this feature to work,...

Page 43

Extended Dual Tone Multiple Frequency (DTMF) 
(continued) 
l Wait 10 seconds and dial number. System will generate 
long dial pad tones. 
m 
l Immediately press HoLD , then press line button to set 0 system to generate long DTMF dial tones. 
l Continue dialing. 
To alternate between long tone and standard tone length during a 
call, 
l Press 0 HoLD , then press line button. 
l Continue dialing. 
Mute Button 
By using the MUTE button, you can block transmission of your 
voice to the distant party. For...

Page 44

Paging 
If you have an external paging unit set up by the installer,. you can 
page over it: 
1. Lift handset. 
2. Press button dedicated to paging; press button pre- 
programmed for paging access; or dial paging access num- 
ber. 
3. Make announcement. 
4. Hang up. 
You can also page all stations through their intercoms (all-call 
paging) or just some stations (zone paging). To do this: 
1. Lift handset. 
2. Press rTCh4 . 
0 
3. Dial 87 for all-call paging. Dial 84, 85, or 86 for zone 
paging. 
4. Make...

Page 45

Personal Ringing Tones 
You can choose one of four different ring tones to easily identify 
your station when it rings. To select one of these rings: 
1. Press @a=@. 
2. Diala,@ ,@ or@ .Oneoffourringing 
tones will be selected and the next time your telephone 
rings, you will hear the difference. 
Privacy 
By pressing a button designated a “privacy button,” you can allow 
another person to join you in a call. This feature is 
preprogrammed by the installer. 
PulselTone Switching 
If your local telephone...

Page 46

G  

Page 47

Table 2. Display Summary 
Display Type 
When Displayed 
Automatic Callback 
Camp-On 118 When waiting for a busy 
telephone to signal that it has be- 
come idle, the display shows that 
the feature is active. 
Call Costing 
Call Cost 1.27 When you push HOLD button 
after making a call, if 
programmed, call cost appears in 
display. 
1 Call Forward 
Fwd To 122 Display shows extension number 
of telephone to which call is for- 
warded. 
Call Messaging 
1‘ 
Message Display prompts for message. 
Entering a...

Page 48

Table 2. Display Summary (continued) 
When Displayed 
xi : 
The display shows extension num- 
1 Dialed Numbers 
200 The display will show all dialed 
numbers or names along with any 
dialed codes. 
Station: 200 
Line: 9782200 
Access Codes: 9p18049782200 
Display Contrast Adjustment 
Contrast Level X Display after holding down Mute 
button for five seconds. 
X = 0 through 7 
Do Not Disturb 
Do Not Disturb Display shows “Do Not Disturb” 
when feature is active. 
I Hold Recall Feature 
Recall S118 L 2 When...

Page 49

Table 2. Display Summary (continued) 
Display Type When Displayed 
1 Last Number Redial 
5552222 When last number dialed is 
redialed, display shows selected 
line, then display shows dialed 
number. 
260 
1 Line Queuing 
Camp-On Ll When queuing for a line, the 
display will show the queuing 
arrangement. 
Camp-On Gl 
Line Selection 
Line 2 When line is selected for calling. 
When ringing line is answered. 
Lines can be programmed to dis- 
play numbers or names, i.e. WATS. 
Mute 
Mute Display shows when...

Page 50

Table 2. Display Summary (continued) 
Display Type 
Paging 
Zone Page X When Displayed 
Display for zone paging (paging 
some stations). 
All Call Display for all-call page (paging 
all stations). 
“Station Name” Display when answering page. 
(Station Name = station originat- 
ing page.) 
Programming for Autodialing and Station 
Speed Dialing 
Location After you press ITCM +k +k 1, this 
appears in the display. 
Line 
Number After you enter location, this ap- 
pears in display. 
After you enter line,...
Start reading Comdial Executech 2000 Instructions Manual

Related Manuals for Comdial Executech 2000 Instructions Manual

All Comdial manuals