Comdial Executech 2000 Instructions Manual

Automatic Redialing 
If the last number you have called is busy or is not answering, use 
this feature. Once activated, it automatically redials the number 
once a minute for 10 minutes. 
To activate automatic redial, 
l Press button programmed for that purpose (that you have 
labeled “auto redial”). 
l Number will be dialed once a minute for 10 minutes. 
If called station is busy, 
l Press auto redial button to begin redial cycle immediately. 
(ITCM light flashes.) 
To cancel automatic redial, 
l Press...

Speed Dialing (continued) 
To speed dial system numbers if on-hook, 
l Press * 
0 . 
l Dial the memory location numbers (01 through 99) 
programmed into the system by the attendant. 
Em 
If off-hook and on a line: 
l Press “OLD . 
0 
l 
Dial a plus the memory location digits 
(01 through 99). 
Last Number Redialing 
The last number dialed can be automatically redialed with a one- 
or two-button action. 
l Press 
0 # . (If on line listening to dial tone, 
press 
0 HOLD , then press # 
0 .) 
e Listen for...

Holding Calls 
Manual Hold 
To place a call on hold, 
l Press@ 
To retrieve a held call, 
l Press line button with flashing light, 
mu 
l Press TAP 
0 if station does not have line appearance. 
Exclusive Hold 
This means that only you can retrieve the held call on your 
telephone. 
To place on exclusive hold, 
l Press 
0 “OLD twice. 
To retrieve exclusive hold, 
l Press line button with flashing light. 
l Press 
0 TAP if station does not have line appearance. 
Direct Station Hold (parking a call to a...

Direct Station Hold (continued) 
To retrieve a direct hold call, 
* From the hold receivin extension, 
dial@@ &. 
To cancel a direct hold call from station that placed call on hold, 
l Dial a @ plus extension number of the station 
holding the call. Doing this reconnects you to the outside 
line. 
Call Park (parking a call to an orbit) 
To park a call in one of nine orbits, 
l While on line, press @a. 
l Dial a park zone access code (91 through 99). 
To retrieve a parked call, 
e From any station, press...

Transferring Calls 
When transferring a call you can either identify the caller before 
you transfer (screened) or you can transfer the call without 
identifying the caller (unscreened). 
Screened Transfer 
To screen and transfer a call to another station in the system, 
l Answer call. 
l Press CONS . 
e!i3 Call is placed on hold automatically. 
l Dial extension number of party to be transferred to. 
Press DSS button for one-button intercom calling. 
I 
* When intercom party answers, announce call. 
l...

Unscreened Transfer (continued) 
l Hang up handset. 
NOTE: If the station to which unscreened tran$ers are made is busy, 
the transferred calls will camp-on at the station. Each call will 
automntically ring the station when it becomes idle. 
l If a transferred call is not answered after a preprogrammed 
time, it will ring back to your station. 
l Answer by pressing flashing line key. 
i. .., 
22  

Making Conference Calls 
Multiline Conference 
(2 outside lines, I inside station) 
To set this up: 
l Make first outside call. 
l Press CONF 
e3 . Outside call is placed on hold automatically. 
l Make second outside call. 
l Press CONF . 
e? Conference is established. 
To remain in conference with one conferee, 
l Press the line button of the remaining party. 
To drop out of established conference, 
0 
Dial a and hang up. 
Add-On Conference Calls 
(1 outside line, 2 inside stations) 
To set this up: 
l...

Three Inside Stations 
To set up a three-party internal conference: 
l Make first internal call. 
l Press 02.4~ . 
e3 Internal call placed on hold automatically. !.... 
:-:, 
l Establish second internal call. (Ask called party to lift 
handset. 
To drop one conferee and remain in conference with other con-  0 
Press @ . Conference is established. 
feree: 
l Stay on line when one party hangs up. 
!. 
i 
I’ . . 
i 
24  

Messaging 
Message Waiting Light 
If your station has been designated as a central message desk, you 
can turn on the message waiting light (above HOLD) of any 
telephone from your station to let the user know that a message 
awaits pickup. 
To receive a message at an alerted station, 
l Observe flashing light. 
l Lift handset. 
l Press @@. 
l Connection to station that left message is automatic. 
To turn on the message waiting light, 
l Press@=@. 
l Dial extension number of station to be alerted. The...

LCD Messaging 
System-supplied messages can be set at a station to be received 
or displayed by a calling LCD speakerphone. These messages 
give information on the status of the telephone user. 
In the back of this guide there is a list entitled “LCD Messages.” i .: 
I. 
Fill it in after the attendant gives you the list of messages. j:. ; 
; :’ 
To turn on message, 
l Dial the desired code number from your message list. The 
default messages of “Back At” and “Call” may be used: 
For default message 1,...