Comdial Dxp Plus Instructions Manual
Here you can view all the pages of manual Comdial Dxp Plus Instructions Manual. The Comdial manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 381
Connecting The DXP To The DVA Complete the QuickQ system installation by connecting the DXP to the DVA. You will not need any kit-supplied components; however, you will need a 66-type station connector block and a 25-pair cable. 1. Mount a 66-type station connector block, and connect it to a DXP digital station board. 2. Mount the QuickQ-supplied connector block, and connect its pre-wired cable to the DVA.3. Use a 25-pair cable to connect the QuickQ connect block to the block that you mounted in step 1....
Page 382
QUICK002 QuickQ- Supplied And Punched-Down 25-Pair Cable Male 50-Pin Connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 501 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 45 46 48 49 50 Station 1 Station 1 Station 2 Station 2 Station 3 Station 3 Station 4 Station 4 Station 5 Station 5 Station 6 Station 6 Station 7 Station 7 Station 8 Station 8 Station 9 Station 9 Station...
Page 383
Connecting The QuickQ PROTECKEY You must connect the suppliedQuickQPROTECKEY to the computer’s parallel port. Refer to Figure 3-6 for details. CAUTION The system will not function if you fail to connect the QuickQ PROTECKEY. Connecting AC Power To The DVA Before applying power to the DVA check all wiring connections and ensure that you have properly configured the Voice Channel Card as described in Section 6, Reviewing TheQuickQDVA Components. Always employ a dedicated 117VAC 15 AMP circuit, with a...
Page 384
Reviewing The System Interconnection Compare your system interconnection with the Figure 3-7 illustration. Figure 3-7. Reviewing The System Interconnection QUICK05A QuickQ- Supplied And Punched-Down 25-Pair Cable Kit-Supplied Modular Jack Kit-Supplied Line Cord Kit- Supplied Line Cord Kit- Supplied Modular Jack Kit- Supplied Modular JackTo COM2 PortTo Parallel PortTo COM1 Port Kit-Supplied Line Cord House WiringHouse Wiring 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30...
Page 385
Section 4 Programming The DXP Digital Communications System You must make certain programming arrangements to ensure that the DXP will work properly with theQuickQ DVA. This section details those DXP parameters that you must arrange. Refer to the DXP Video Terminal Programming Instructions for complete programming details. You can find that instruction included in the literature binder that accompanies your DXP digital communications system. Programming The DXP System Parameters Feature Name QuickQ...
Page 386
Programming The DXP Line Parameters Configure each line with the parameters shown in the table. Program the line names as L001 for line one, L002 for line two, L003 for line three, and so forth until you have named every line that you need for the QuickQ installation. You cannont change these line names. Feature Name QuickQ Parameter Name Lnnn Type Loop Start Disabled No Music On Hold Source 1 Privacy Release No SMDR Record Yes Cost Incoming No —Incoming Cost Delay No Delay —Incoming Cost Route 32...
Page 387
Programming Class Of Service For Master Channel 1 You can assign any class of service from COS1 through COS32 to the master channels and voice ports; however, reserve the COS that you do assign exclusively for the master channel. Be sure to enter the COS number that you use here as the COS entry on the station programming features for the master channel voice ports. Feature Name QuickQ Parameters Account Code No Automatic Hold On Intercom Yes Automatic Hold On Lines Yes Background Music No Call Cost...
Page 388
Programming Class Of Service For Master Channel 2 You can assign any class of service from COS1 through COS32 to the master channels and voice ports; however, reserve the COS that you do assign exclusively for the master channel. Be sure to enter the COS number that you use here as the COS entry on the station programming features for the master channel voice ports. Feature Name QuickQ Parameters Account Code No Automatic Hold On Intercom Yes Automatic Hold On Lines Yes Background Music No Call Cost...
Page 389
Programming The Master Channel 1 Voice Port Station Features Feature Name QuickQ Parameters Personal Intercom 101 Name MASTER 1 Class Of Service (enter COS for master channel) * Speed Dial Sets3 Idle Line PriorityNone Intercom Hunt ListNone Group Intercom Access 4201–4264 Prime Type No Prime —Line 1 —Line Group 1 —Intercom 101 Tone First Yes Call Announce Beeps 1 Default Forward Type No Forward —Intercom Forward To: 101 —Forward Type Personal Calls Forward Ring No-Answer Ring Busy No Direct Ring None...
Page 390
Programming The Master Channel 2 Voice Port Station Features Feature Name QuickQ Parameters Personal Intercom 102 Name MASTER 2 Class Of Service (enter COS for master channel) * Speed Dial Sets3 Idle Line PriorityNone Intercom Hunt ListNone Group Intercom Access 4201–4264 Prime Type No Prime —Line 1 —Line Group 1 —Intercom 102 Tone First Yes Call Announce Beeps 1 Default Forward Type No Forward —Intercom Forward To: 102 —Forward Type Personal Calls Forward Ring No-Answer Ring Busy No Direct Ring None...