Comdial Digital Telephone System Instructions Manual

System ProgramingSystem Configuration 
- Miscellaneous Features - continued
IMl66-107Press 
ITCM +##746% )
System Clock
The system clock maintains current
date and time information. The system
provides this information to LCD
speakerphones for display. Set the
system time with this feature.
The system attendant also has access
to this feature.
System Speed Dial
You can program a special
system-wide list of numbers that all
users can use for automatic dialing.
The system attendant can also
program the...

IMl66-107System ProgramingSystem Configuration 
- Miscellaneous Features - continued
Press ITCM ++#746+k
Tandem Attendant1. Dial 24.“TANDEM ATTN XXX ’
When you enable this feature, a recall2. Press Al to toggle between enable and disable (LED On = Enable).
from an unanswered call transfer or
-OR-
timed hold recall will ring at both
Dial 1 to enable.“TANDEM 
ATN OFF
attendant stations. When you disable
Dial 2 to disable
it, only the attendant station that
(Al LED is on).“TANDEM 
Al7N ON ’transferred the...

System ProgramingIMl66-107
System Configuration -Timing FeaturesPress 
ITCM %#746+#
recall time: (LED On = Selected Time)
- Dial 1 or press Al = 1 min.“C.P. RECALL 1 ”
Wogramming feature automatically- Dial 2 or press A2 = 2 min.“C.P. RECALL 2 ”
etums to a timed hold recall condition- Dial 3 or press A3 = 3 min“C.P. RECALL 3 ’it the parking station.- Dial 4 or press A4 = 4 min.“C.P. RECALL 4 ”
- Dial 5 or press A5 = 5 min.“C.P. RECALL 5 ”
- Dial 6 or press A6 = 6 min“C.P. RECALL 6 *
- Dial 7 or press A9...

IMl66-107
System ProgramingSystem Configuration -Timing Features 
- continued1 Press 
ITCM W746% 1
Recall/Flash:
The system can generate either a line
zlisconnect (recall) or a host system
‘eature access signal (flash) depending
Jpon the programmed time.
Timed Hold Recall
After a call has been on hold for the.
length of time set with this
programming feature, the system will
recall the station that placed the call on
hold.
Unanswered Call Transfer
Recall Time
A transferred call that remains
unanswered...

System ProgramingIMl66-107
System Configuration - Feature Inhibiting
Press ITCM %#746%
:eature Inhibit Programming1. Dial 29.“FEATURE INHIBIT”‘ou can disable certain features
2. Select feature:
y&em-wide to provide a basic- Dial 01 to disable Line Group 1.
slephone system for use in- Dial 02 to disable Line Group 2.
lstallations where a large proportion of- Dial 03 to disable Line Group 3.78 stations are accessible to
Inauthorized users thus subject to- Dial 04 to disable Line Group 4.smpering.
- Dial 05...

System ProgrammingIMl66-107
Line Configuration’
 0 To make a record of the programming configuration, mark the desired requirements in the line class of service
records chart found at the end of Chapter 4.
0 To make the programming selections, dial the feature code and then dial the configuration code (or press the
programming button where appropriate).
NOTE: A lighted LED next to the programming button for the selection indicates the current 
configuration.
When
a sing/e button provides a toggle...

IMl66-107System Programming
ILine Configuration - continued
Press ITCM +%#746+%.
Automatic Privacy, Privacy Release
You can make a line private or non-private.
In the private mode, a station has exclusive
use of a line during a call. Lines are private
unless you re-program them and make
them non-private. Further, you can arrange
for individual station to automatically
release privacy while on certain lines. With
this arrangement, other stations can join
that particular station whenever it is on the...

System ProgrammingIMl66-107Line Configuration 
- continued
Press 
ITCM f#746%.Line Groups
Group outside lines of the same type
together for dial-up outgoing access.
NOTE: When you do this, 
the feature
m0f77aridy arranges the
system for hybrid operation.
Remember, hybrid operation
may incur a higher monthly
tariff than the key sysrem
.operarion incurs. Ask the local
telephone company for details
User access codes for the line
groups 
are:Group 1 
= Dial 9
Group 2 = Dial 81Group 3 = Dial 82
Group 4 = Dial...

IMl66-107System ProgrammingLine Configuration 
- continued
Press 
ITCM ++#746%.
.ine Names
‘ou can name lines as to their function to
dentify them for use. Names such as
VATS, CO, etc., when appearing on the
CD speakerphone displays, make 
locatin!
t desired line easier for the station user to
lo. A line name can contain up to five
:haracters.
1. Dial 34.“LINE NAME”
2. Select line ports to be named (LED On 
= Selected).
Line port 1-14 = Dial 
01 - 14 or Press Al - Al4
Line port 15, 16 = Dial 15,16 or...

System ProgrammingIMl66-107
Press ITCM %#746%.
Line Configuration - continued
Line Port FunctionsTo program an auxiliary line port,
rvlim: You can condition a line1. Dial 32.“AUXlLlARY LINES
Dart to serve as a port for an external
2. Select line ports to be assigned (LED On = Aux. Line Port).
Daging amplifier.
Line port 1-14 = Dial 01 - 14 or Press Al - Al4n. ., #entral Off ce I III&Z You can condition lineLine port 15, 16 = Dial 15,16 or press Bl, 82
ports to serve as a ports for standardLine port 17-24...