Comdial Digital Telephone System Instructions Manual

InstallationIMl66-107Installer/User Information Regarding FCC Rules And Regulations
This electronic key system complies with Federal
Communications Commission (FCC) Rules, Part 68. The
FCC registration label on the KSU contains the FCC
registration number, the ringer equivalence number, the
model number, and the serial number or production date of
the system.
Notification To Telephone Company
Unless a telephone operating company provides and installs
the system, the telephone operating company which...

IMl66-107System Programming
Chapter 4
System Programming
General Programming Information
Perform configuration programming from station port
10 or station 
port 12. The system will not accept
programming commands from any other station port in
the system. For best programming results, employ an
LCD speakerphone. While you can install any
non-LCD digital telephone and use it for programming,
visual feedback of the programming operations will not
be available. Configuration programming from station
port 10...

System ProgrammingIMl66-107Converting Button Designations
When you first power a new system with no
telephones connected, it defaults its station ports as
follows:
ziFEY-=-DigiTech 24-line telephones
lnnnnImpact 
24-line telephones
When you connect a telephone to a powered-up
system or when you turn on the AC power to a system
after you have connected a telephone to it, the
telephone identifies itself to the system but its button
mapping will be defaulted for the telephone types
denotes above until you...

IM166-107System ProgrammingClass Of Service Programming
Class of service programming provides you with the means for programming all of the system variables; however,
you may elect to program only the line attributes and leave the remainder of the system variables set to their
default values.
Perform the class of service programming in the sequence shown below.
Automatic Hold\
When you enable this feature, the
telephone user can automatically
existing line call on hold when she or he
presses another line...

System ProgramingIMl66-107
Master Clear and Class Of Service Defaults
Not on/y does the master clear procedure return ALL programmed variables to a known
stateof 
ooeration.it also clears all currently stored autodial and speed dial numbers.
Aaster Clearl.PresslTCMDial##7466“CONFIG. MODE”.
qetums entire system configuration toactory settings and clears all stomd auto2. Dial 90“MASTER CLEAR :
u?d speed dial numbers.3. Dial 5 1 6 8 4 to clear the entire system.
System returns to normal operation mode...

IM166-107
System Programing
System Configuration - Miscellaneous Features
0 To make a record of the programming configuration, mark the desired requirements in the system class of
service records chart found at the end of Chapter 4.
0 To make the programming selections, dial the feature code and then dial the configuration code (or press
the programming button where appropriate).
NOTE: A lighted LED next to the programming button for the selection indicates the current configuration.
When a sing/e button...

System ProgramingIM166-107System Configuration 
- Miscellaneous Features - continued
Press ITCM ++#746+#
nhibit, and Override“BUTON MAPPING ’
4 telephone user can press a button“ASSIGN DND CODE ”
either one that you have mapped on
3. Select button to be programmed:
tis or her station or one that is provided- Press Al - A14, Bl - B8.)y an interactive button on an LCD
speakerphone) to set his or her station4. Select station ports to be programmed with a DND button
o a DND condition.(LED On = Selected...

IMl66-107System ProgramingSystem Configuration 
- Miscellaneous Features - continued
Press 
ITCM *#746*
LCD Messaging
U’OIJ can create messages that
:elephone users can set at their
stations to be displayed by any LCD
speakerphone that calls them on the
ntercom line. The system provides two
standard messages but you can use
this programming procedure to create
up to 10 custom messages.
System attendants also have access to
this feature.
Music On Hold
When you connect an external music
source to the...

System ProgramingIMl66-107System Configuration 
- Miscellaneous Features - continued
Press ITCM %#746++
)A Port Options
fou can assign lines to the PA port for
direct ring, delayed ring, or night
ransfer (of ringing). You can also
assign zone or all-call paging to the PA
)Ort.
lou can select the tracking source for
he ringing relay to be either station 17
inging or the ringing that you have
issigned to the paging port. Making it
rack the ringing that you have
issigned to the PA port provides relay...

IM166-107System ProgramingSystem Configuration 
- Miscellaneous Features - continued
Press ITCM +##746t
station Monitoring: The DSS/BLF at a
;tation provides idle, busy, and ringing
status of all of the monitored stations.
f users deem the flashing BLF lights
associated with visual ring indication
Gstracting, you can disable this visual
ndication system-wide using this
xocedure.
f you enable this visual ring indication,
(ou can also enable audible indication
If both direct and delayed ringing on a
)er...