Cisco Touch 8 User Guide

61
The Call Status window provides information on call rate, encryption, 
as well as important video and audio  parameters.
This information is typically what you  may be asked by the technical staff 
to provide in the unlikely event of  system malfunction.
Settings
Call StatusAbout Call Status 
D1458221 User Guide Cisco TelePresence
Profile Series, Codec C-series, Quick Set C20 
SX20 Quick Set, MX200, MX300
Produced: December 2014 for TC7.3
All contents 

62
For troubleshooting purposes you may enable additional system  logging. Follow the on-screen 
instructions.
Note that system performance may  be influenced by an ongoing system  logging.
This information is typically what you  may be asked by the technical staff 
to provide in the unlikely event of  system malfunction.
Settings
Diagnostic ModeAbout Diagnostics 
D1458221 User Guide Cisco TelePresence
Profile Series, Codec C-series, Quick Set C20 
SX20 Quick Set, MX200, MX300
Produced: December 2014 for...

63
Use this to restart your system in an orderly and controlled manner. No  settings are lost.
Settings
Restart SystemAbout Restart 
D1458221 User Guide Cisco TelePresence
Profile Series, Codec C-series, Quick Set C20 
SX20 Quick Set, MX200, MX300
Produced: December 2014 for TC7.3
All contents 

64
The Administrator settings will normally have been password 
protected by your video support 
team.
Enter Username and Password 
followed by tapping Log in.
Settings
AdministratorAbout Administrator 
D1458221 User Guide Cisco TelePresence
Profile Series, Codec C-series, Quick Set C20 
SX20 Quick Set, MX200, MX300
Produced: December 2014 for TC7.3
All contents 

65
For systems with two cameras set up 
for speaker tracking, this window lets 
you specify the tracking mode. Select  between Normal and Fast.
In addition, this window lets you con-
figure the Snap to Whiteboard feature. 
Just follow the wizard to set up this  feature.
Note!  Speaker tracking microphones 
are height-above-floor sensitive. This  is used to make the system respond 
to a speaking person standing by the 
whiteboard only. A person sitting in  front of the whiteboard will then avoid  invoking...

66
This window lets you specify your preferred date and time formats, as 
well as the time zone.
If you set the Date and Time Mode 
to Auto (as has been done in this 
example), the system will look for an  NTP server and get date and time 
from there.
If you choose to set NTP mode to 
Manual (as has been done in this  example), you must specify the NTP server address to make things work.
Settings
Administrator Settings—Set Date and TimeAbout Time Setting 
D1458221 User Guide Cisco TelePresence
Profile...

67
If you enable Auto Answer the 
system will respond by itself to  incoming calls after a delay specified 
by you. Note that an activated auto 
answer may not provide you with 
the privacy desired. In the example  shown here Auto Answer is set to 
Off. 
On certain occasions you may have to change the bandwidth (and hence the quality) of the call. Some 
configurations may have different  incoming and outgoing bandwidths 
(typically ADSL connections), and  you may specify the default call rate  to ensure...

68
There is a Provisioning Wizard available to get your system online. 
Tap Start and follow the on-screen  instructions.
Caution! There is no Cancel 
function letting you exit the menu  undoing any changes you have 
made. Take care!
Settings
Administrator Settings—Provisioning WizardAbout the Wizard
To exit 
Administrator  Settings, tap  Back.
To exit Settings  as such, tap  Exit.
Note that there  is no Cancel 
function letting  you exit the 
menu undoing 
any changes you  have made.
 Take care!...

69
There are basically two modes of video conferencing; viz. MultiWay and MultiSite.
• To enable MultiWay, a MultiWay  address must have been entered.
• If a MultiWay address has been 
specified and MultiWay is selected, 
MultiWay will always be used for 
video conferencing.
• If a MultiWay address has been 
specified, but MultiSite is selected, 
MultiSite will be used.
• If set to Auto , MultiWay will be 
used if a MultiWay address 
has been specified, otherwise 
MultiSite will be used.
• If set to Off...

70
This window shows relevant pairing information.
Settings
Administrator Settings—PairingAbout Pairing
To exit 
Administrator  Settings, tap  Back.
To exit Settings  as such, tap  Exit.
Note that there  is no Cancel 
function letting  you exit the 
menu undoing 
any changes you  have made.
 Take care! 
D1458221 User Guide Cisco TelePresence
Profile Series, Codec C-series, Quick Set C20 
SX20 Quick Set, MX200, MX300
Produced: December 2014 for TC7.3
All contents