Cisco Touch 8 User Guide
Have a look at the manual Cisco Touch 8 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 53 Cisco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
61 The Call Status window provides information on call rate, encryption, as well as important video and audio parameters. This information is typically what you may be asked by the technical staff to provide in the unlikely event of system malfunction. Settings Call StatusAbout Call Status D1458221 User Guide Cisco TelePresence Profile Series, Codec C-series, Quick Set C20 SX20 Quick Set, MX200, MX300 Produced: December 2014 for TC7.3 All contents
62 For troubleshooting purposes you may enable additional system logging. Follow the on-screen instructions. Note that system performance may be influenced by an ongoing system logging. This information is typically what you may be asked by the technical staff to provide in the unlikely event of system malfunction. Settings Diagnostic ModeAbout Diagnostics D1458221 User Guide Cisco TelePresence Profile Series, Codec C-series, Quick Set C20 SX20 Quick Set, MX200, MX300 Produced: December 2014 for TC7.3 All contents
63 Use this to restart your system in an orderly and controlled manner. No settings are lost. Settings Restart SystemAbout Restart D1458221 User Guide Cisco TelePresence Profile Series, Codec C-series, Quick Set C20 SX20 Quick Set, MX200, MX300 Produced: December 2014 for TC7.3 All contents
64 The Administrator settings will normally have been password protected by your video support team. Enter Username and Password followed by tapping Log in. Settings AdministratorAbout Administrator D1458221 User Guide Cisco TelePresence Profile Series, Codec C-series, Quick Set C20 SX20 Quick Set, MX200, MX300 Produced: December 2014 for TC7.3 All contents
65 For systems with two cameras set up for speaker tracking, this window lets you specify the tracking mode. Select between Normal and Fast. In addition, this window lets you con- figure the Snap to Whiteboard feature. Just follow the wizard to set up this feature. Note! Speaker tracking microphones are height-above-floor sensitive. This is used to make the system respond to a speaking person standing by the whiteboard only. A person sitting in front of the whiteboard will then avoid invoking the snap feature. To make this work the system will look and listen for a face located in the upper half of the defined whiteboard area. The whiteboard must be located on the wall opposing the camera system. The feature has not been designed for any other angle of incidence. For a more detailed discussion on the Snap to Whiteboard feature, see the Administrator Guide for your video system. Settings Administrator Settings—TrackingAbout Tracking Tap as shown to invoke the Snap to Whiteboard setup wizard. D1458221 User Guide Cisco TelePresence Profile Series, Codec C-series, Quick Set C20 SX20 Quick Set, MX200, MX300 Produced: December 2014 for TC7.3 All contents
66 This window lets you specify your preferred date and time formats, as well as the time zone. If you set the Date and Time Mode to Auto (as has been done in this example), the system will look for an NTP server and get date and time from there. If you choose to set NTP mode to Manual (as has been done in this example), you must specify the NTP server address to make things work. Settings Administrator Settings—Set Date and TimeAbout Time Setting D1458221 User Guide Cisco TelePresence Profile Series, Codec C-series, Quick Set C20 SX20 Quick Set, MX200, MX300 Produced: December 2014 for TC7.3 All contents
67 If you enable Auto Answer the system will respond by itself to incoming calls after a delay specified by you. Note that an activated auto answer may not provide you with the privacy desired. In the example shown here Auto Answer is set to Off. On certain occasions you may have to change the bandwidth (and hence the quality) of the call. Some configurations may have different incoming and outgoing bandwidths (typically ADSL connections), and you may specify the default call rate to ensure a stable video quality. The default protocol may also be specified. In the example shown, the protocol has been set to SIP. Caution! There is no Cancel function letting you exit the menu undoing any changes you have made. Take care! Settings Administrator Settings—Call DetailsAbout Call Details To exit Administrator Settings, tap Back. To exit Settings as such, tap Exit. Note that there is no Cancel function letting you exit the menu undoing any changes you have made. Take care! D1458221 User Guide Cisco TelePresence Profile Series, Codec C-series, Quick Set C20 SX20 Quick Set, MX200, MX300 Produced: December 2014 for TC7.3 All contents
68 There is a Provisioning Wizard available to get your system online. Tap Start and follow the on-screen instructions. Caution! There is no Cancel function letting you exit the menu undoing any changes you have made. Take care! Settings Administrator Settings—Provisioning WizardAbout the Wizard To exit Administrator Settings, tap Back. To exit Settings as such, tap Exit. Note that there is no Cancel function letting you exit the menu undoing any changes you have made. Take care! D1458221 User Guide Cisco TelePresence Profile Series, Codec C-series, Quick Set C20 SX20 Quick Set, MX200, MX300 Produced: December 2014 for TC7.3 All contents
69 There are basically two modes of video conferencing; viz. MultiWay and MultiSite. • To enable MultiWay, a MultiWay address must have been entered. • If a MultiWay address has been specified and MultiWay is selected, MultiWay will always be used for video conferencing. • If a MultiWay address has been specified, but MultiSite is selected, MultiSite will be used. • If set to Auto , MultiWay will be used if a MultiWay address has been specified, otherwise MultiSite will be used. • If set to Off , no video conferencing will be possible. • Any use of the MultiSite feature requires the presence of the MultiSite option. Caution! There is no Cancel function letting you exit the menu undoing any changes you have made. Take care! Settings Administrator Settings—Multipoint ModeAbout Multipoint To exit Administrator Settings, tap Back. To exit Settings as such, tap Exit. Note that there is no Cancel function letting you exit the menu undoing any changes you have made. Take care! D1458221 User Guide Cisco TelePresence Profile Series, Codec C-series, Quick Set C20 SX20 Quick Set, MX200, MX300 Produced: December 2014 for TC7.3 All contents
70 This window shows relevant pairing information. Settings Administrator Settings—PairingAbout Pairing To exit Administrator Settings, tap Back. To exit Settings as such, tap Exit. Note that there is no Cancel function letting you exit the menu undoing any changes you have made. Take care! D1458221 User Guide Cisco TelePresence Profile Series, Codec C-series, Quick Set C20 SX20 Quick Set, MX200, MX300 Produced: December 2014 for TC7.3 All contents