Cisco Prime Nerk 43 User Guide
Have a look at the manual Cisco Prime Nerk 43 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 53 Cisco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
16-13 Cisco Prime Network 4.3.2 User Guide Chapter 16 Managing DWDM Networks Viewing Performance Monitoring Configuration OTN PM Settings Tab Type OTN performance monitoring parameter being tracked: bbe-pm-fe—Far-end path monitoring background block errors (BBE-PM). Indicates the number of background block errors recorded in the optical transport network (OTN) path during the performance monitoring time interval. bbe-pm-ne—Near-end path monitoring background block errors (BBE-PM). bbe-sm-fe—Far-end section monitoring background block errors (BBE-SM). Indicates the number of background block errors recorded in the OTN section during the performance monitoring time interval. bbe-sm-ne—Near-end section monitoring background block errors (BBE-SM). bber-pm-fe—Far-end path monitoring background block errors ratio (BBER-PM). Indicates the background block errors ratio recorded in the OTN path during the performance monitoring time interval. bber-pm-ne—Near-end path monitoring background block errors ratio (BBER-PM). bber-sm-fe—Far-end section monitoring background block errors ratio (BBER-SM). Indicates the background block errors ratio recorded in the OTN section during the performance monitoring time interval. bber-sm-ne—Near-end section monitoring background block errors ratio (BBER-SM) es-pm-fe—Far-end path monitoring errored seconds (ES-PM). Indicates the errored seconds recorded in the OTN path during the performance monitoring time interval. es-pm-ne—Near-end path monitoring errored seconds (ES-PM). es-sm-fe—Far-end section monitoring errored seconds (ES-SM). Indicates the errored seconds recorded in the OTN section during the performance monitoring time interval. es-sm-ne—Near-end section monitoring errored seconds (ES-SM). esr-pm-fe—Far-end path monitoring errored seconds ratio (ESR-PM). Indicates the errored seconds ratio recorded in the OTN path during the performance monitoring time interval. esr-pm-ne—Near-end path monitoring errored seconds ratio (ESR-PM). esr-sm-fe—Far-end section monitoring errored seconds ratio (ESR-SM). Indicates the errored seconds ratio recorded in the OTN section during the performance monitoring time interval. esr-sm-ne—Near-end section monitoring errored seconds ratio (ESR-SM). fc-pm-fe—Far-end path monitoring failure counts (FC-PM). Indicates the failure counts recorded in the OTN path during the performance monitoring time interval. fc-pm-ne—Near-end path monitoring failure counts (FC-PM). fc-sm-fe—Far-end section monitoring failure counts (FC-SM). Indicates the failure counts recorded in the OTN section during the performance monitoring time interval. fc-sm-ne—Near-end section monitoring failure counts (FC-SM). Table 16-4 Client DWDM PM Settings Properties Window and Tabs (continued) Field Description
16-14 Cisco Prime Network 4.3.2 User Guide Chapter 16 Managing DWDM Networks Configuring and Viewing DWDM Configuring and Viewing DWDM The following commands can be launched from the inventory by right-clicking the appropriate node and choosing Commands > Configuration. Your permissions determine whether you can run these commands (see Permissions for Managing DWDM, page B-16). To find out if a device supports these commands, see the Cisco Prime Network 4.3.2 Supported Cisco VNEs. Type (cont.) ses-pm-fe—Far-end path monitoring severely errored seconds (SES-PM). Indicates the severely errored seconds recorded in the OTN path during the performance monitoring time interval. ses-pm-ne—Far-end path monitoring severely errored seconds (SES-PM). ses-sm-fe—Far-end section monitoring severely errored seconds (SES-SM). Indicates the severely errored seconds recorded in the OTN section during the performance monitoring time interval. ses-sm-ne—Near-end section monitoring severely errored seconds (SES-SM). sesr-pm-fe—Far-end path monitoring severely errored seconds ratio (SESR-PM). Indicates the severely errored seconds ratio recorded in the OTN path during the performance monitoring time interval. sesr-pm-ne—Near-end path monitoring severely errored seconds ratio (SESR-PM). sesr-sm-fe—Far-end section monitoring severely errored seconds ratio (SESR-SM). Indicates the severely errored seconds ratio recorded in the OTN section during the performance monitoring time interval. sesr-sm-ne—Near-end section monitoring severely errored seconds ratio (SESR-SM). uas-pm-fe—Far-end path monitoring unavailable seconds (UAS-PM). Indicates the unavailable seconds recorded in the OTN path during the performance monitoring time interval. uas-pm-ne—Near-end path monitoring unavailable seconds (UAS-PM). uas-sm-fe—Far-end section monitoring unavailable seconds (UAS-SM). Indicates the unavailable seconds recorded in the OTN section during the performance monitoring time interval. uas-sm-ne—Near-end section monitoring unavailable seconds (UAS-SM). Threshold Threshold configured for the parameter. TCA If enabled, indicates a TCA is generated if the value of the parameter crosses the threshold during the performance monitoring period. If disabled, TCAs are not generated if the value crosses the threshold. Table 16-4 Client DWDM PM Settings Properties Window and Tabs (continued) Field Description
16-15 Cisco Prime Network 4.3.2 User Guide Chapter 16 Managing DWDM Networks Configuring and Viewing DWDM Command Navigation Input Required and Notes Controller Data Show >N/A; performed from command launch point PM History DataPM interval type: 15-min or 24-hour Interval number RTPM CountersPM interval type: 15-min or 24-hour RTPM ThresholdPM interval type: 15-min or 24-hour Wav e l e n g t h M a pN/A; performed from command launch point IM Trace DetailsCard location (for example, 0/5/CPU0) Device LogN/A; performed from command launch point Counters Clear >N/A; performed from command launch point Channel Configure >Channel number Option: Set or reset channel FEC ModeG.709 FEC mode: Disabled, enhanced, or standard G.709 ODUODU alarm type: ais, bdi, lck, oci, ptim, or tim Option: Enable or disable alarm type G.709 OTUOTU alarm type: bdi, fecmismatch, iae, lof, lom, los, sd-ber, sf-ber, or tim Option: Enable or disable alarm type
16-16 Cisco Prime Network 4.3.2 User Guide Chapter 16 Managing DWDM Networks Configuring and Viewing DWDM G.709 TTI Configure >Optical channel unit type: ODU or OTU TTI type: Expected or sent TTI string type: ASCII or hex TTI string Option: Set or reset TTI string G.709 WrapperOption: Disable or enable G.709 wrapper Laser StateLaser state: Switch off or on LoopbackLoopback value: Internal or line Option: Set or remove PM FEC DataPM interval type FEC alarm type: Ec-bits—Bit errors corrected (BIEC); the number of bit errors corrected in the DWDM trunk line during the performance monitoring time interval Uc-words—Uncorrectable words; the number of uncorrectable words detected in the DWDM trunk line during the performance monitoring time interval TCA options: Enable or disable TCA generation Threshold option. Set configures the value on the device; reset is the default. If you select blank, the threshold value is not used. Threshold value Command Navigation Input Required and Notes
16-17 Cisco Prime Network 4.3.2 User Guide Chapter 16 Managing DWDM Networks Configuring and Viewing DWDM PM Optics Data Configure >PM interval: 15-min or 24-hour Optics alarm type: lbc—Laser bias current opr—Optical power on the unidirectional port opt—Transmit optical power in dBm Maximum TCA option: Enable or disable Maximum threshold option: Choosing Set configures the value on the device; Reset is the default. If you select blank, the threshold value is not used. Maximum threshold Minimum TCA option: enable or disable Minimum threshold option: Choosing Set configures the value on the device; Reset is the default. If you select blank, the threshold value is not used. Minimum threshold PM OTN DataPM interval: 15-min or 24-hour OTN alarm type. For a list of types and their descriptions, see the OTN PN Settings Tab information in Table 16-4 on page 16-11. TCA option: Enable or disable Threshold option: Choosing Set configures the value on the device; Reset is the default. If you select blank, the threshold value is not used. Threshold value Tr a n s m i t P o w e rTransmit power in dBm Option: Set or reset transponder Tx threshold Rx LOS ThresholdRx LOS threshold value Option: Set or reset transponder Rx threshold Command Navigation Input Required and Notes
16-18 Cisco Prime Network 4.3.2 User Guide Chapter 16 Managing DWDM Networks Configuring and Viewing DWDM
CH A P T E R 17-1 Cisco Prime Network 4.3.2 User Guide 17 Managing MPLS Networks The following topics describe how to view and manage aspects of Multiprotocol Label Switching (MPLS) services using the Vision client, including the MPLS service view, business configuration, and maps. The topics also describe the device inventory specific to MPLS VPNs, including routing entities, label switched entities (LSEs), BGP Neighbours, Multiprotocol BGP (MP-BGP), VRF instances, pseudowires, and TE tunnels. If you cannot perform an operation that is described in these topics, you may not have sufficient permissions; see Permissions for Managing MPLS Services, page B-18. Working with MPLS-TP Tunnels, page 17-6 Viewing VPNs, page 17-19 Managing VPNs, page 17-22 Working with VPN Overlays, page 17-25 Monitoring MPLS Services, page 17-27 Configuring VRFs, page 17-62 Configuring IP Interfaces, page 17-63 Auto-IP in PN, page 17-63 Configuring Auto-IP, page 17-63 Configuring MPLS-TP, page 17-63 Configuring MPLS-TE, page 17-71 Configuring MPLS, page 17-71 Configuring RSVP, page 17-72 Configuring BGP, page 17-72 Configuring VRRP, page 17-73 Configuring Bundle Ethernet, page 17-74 Working with FEC 129-based Pseudowire, page 17-76 Viewing IPv6 Information (6VPE) Prime Network supports IPv6 for: Gateways, clients, and units using IPv6. Communications between VNEs and devices in IPv6 environments, whether the device management IP address is IPv4 or IPv6.
17-2 Cisco Prime Network 4.3.2 User Guide Chapter 17 Managing MPLS Networks Viewing IPv6 Information (6VPE) Polling and notification using the following protocols over IPv6: –SNMP v1, SNMPv2c, and SNMPv3 –Te l n e t –SSHv2 –ICMP –XML (for Cisco IOS XR devices) –HTTP (for Cisco UCS and VMware vCenter devices) All reports with devices that use IPv6 addresses. Fault management, including event processing and service alarm generation. Prime Network supports correlation and path tracing for: 6PE and native IPv6 networks. IPv6 BGP address families. IPv6 GRE tunnels. IPv6 VPN over MPLS, also known as 6VPE, uses the existing MPLS IPv4 core infrastructure for IPv6 transport to enable IPv6 sites to communicate over an MPLS IPv4 core network using MPLS label switch paths (LSPs). 6VPE relies on MP-BGP extensions in the IPv4 network configuration on the PE router to exchange IPv6 reachability information. Edge routers are configured to be dual-stacks running both IPv4 and IPv6, and use the IPv4-mapped IPv6 address for IPv6 prefix reachability exchange. In 6VPE environments, Prime Network supports: Modeling of OSPFv3 routes between PE and CE devices. IPv6 addresses for BGP Neighbours for MP-BGP. Correlation and path tracing. The Vision client displays IPv6 addresses when they are configured on PE and CE routers in the IP interface table. IPv6 addresses are: Displayed in the Vision client map pane for IPv6 links. Displayed in logical and physical inventory for routing and interface information, including IP, PPP, and High-Level Data Link Control (HDLC). Used in Cisco PathTracer to trace paths and present path trace results.
17-3 Cisco Prime Network 4.3.2 User Guide Chapter 17 Managing MPLS Networks Viewing IPv6 Information (6VPE) Table 17-1 describes where IPv6 information appears in logical and physical inventory. Table 17-1 IPv6 Information in Inventory Inventory Location Description Logical Inventory 6rd Tunnels The Tunnel Edges table displays IPv6 addresses and the IPv6 prefixes that are used to translate IPv4 addresses to IPv6 addresses. For more information, see Viewing 6rd Tunnel Properties, page 17-49. Access Lists The Type field displays IPv6 for IPv6 access lists. If an IPv6 access list is configured, the Access List Properties window displays IPv6 addresses in the Source, Destination, Source Wildcard, and Destination Wildcard fields. Carrier Grade NAT Carrier Grade NAT service types include 6rd and XLAT. For more information, see Viewing Carrier Grade NAT Properties in Logical Inventory, page 20-2. GRE Tunnels The IP Address field supports IPv6 addresses. For more information, see Viewing MPLS Pseudowire Over GRE Properties, page 26-31. IS-IS IS-IS properties support: IPv6 address families in the Metrics tab. IPv6 addresses in the Neighbours tab and the IS-IS Neighbour Properties window. For more information, see Viewing IS-IS Properties, page 18-130. MPBGPs IP address family identifiers indicate the BGP peer address family: IPv4, IPv6, Layer 2 VPN, VPNv4, or VPNv6. MP-BGP BGP Neighbour entries display IPv6 addresses. For information, see Viewing MP-BGP Information, page 17-48. OSPFv3 IPv6 addresses are displayed for OSPF Neighbour interface addresses, OSPF interface internet addresses, OSPF Neighbour properties window, and OSPF interface properties window. For more information, see Viewing OSPF Properties, page 18-133. Routing Entities IPv6 addresses appear in the IP Interfaces tab, the IPv6 Routing tab, and the interface properties window. IPv6 addresses are displayed in the NDP Table tab and the ARP Entry Properties window. VRRP groups using IPv6 display IPv6 addresses in the IP Interfaces Properties window in the VRRP group tab. For more information, see Viewing Routing Entities, page 17-32. VRFs IPv6 addresses appear in the IPv6 tab, Sites tab, VRF Properties window, and IP Interface Properties window. For more information, see Viewing VRF Properties, page 17-28.
17-4 Cisco Prime Network 4.3.2 User Guide Chapter 17 Managing MPLS Networks Viewing IPv6 Information (6VPE) The IP addresses that appear depend on whether the interface has only IPv4 addresses, only IPv6 addresses, or both IPv4 and IPv6 addresses, as shown in Table 17-2. Note the following when working with IPv6 addresses: MPLS label switching entries and Label Switching Entities (LSEs) do not display IPv6 addresses. However, the Neighbour Discovery Protocol (NDP) table does display IPv6 addresses. Prime Network supports all the textual presentations of address prefixes. However, the Vision client displays both the IP address and the subnet prefix, for example: 12AB::CD30:123:4567:89AB:CDEF, 12AB:0:0:CD30::/60 NoteInterfaces or subinterfaces that do not have IP addresses are not discovered and therefore are not shown in the Vision client. Figure 17-1 shows a port inventory view of a port with IPv4 and IPv6 addresses. In this example, one IPv4 address and multiple IPv6 addresses are provisioned on the interface. The primary IPv4 address appears in the interface table and properties window. If secondary IPv4 addresses were provisioned on the interface, they would appear in the properties window. IPv6 addresses provisioned on the interface appear in the properties window and Sub Interfaces tab. Physical Inventory Port IPv6 addresses appear in the Subinterfaces tab and interface properties popup window. Table 17-1 IPv6 Information in Inventory (continued) Inventory Location Description Table 17-2 IP Addresses Displayed in the Interface Table and Properties Window Addresses Interface Table Properties Window IPv4 only Primary IPv4 address The primary IPv4 address and any secondary IPv4 addresses. IPv6 only Lowest IPv6 address All IPv6 addresses. IPv6 and IPv4 Primary IPv4 address All IPv4 and IPv6 addresses.