Cisco D9854i Manual

 
 
 D9854 Receiver Alarm Messages 
 
78-4021470-01 Rev J 267 
 
Warning Message 
Type 
Message Cause/Remedy Description 
CAT timeout # Set cat is lost Cause: Uplink is not 
sending or is sending 
intermittently.  
Remedy: Clear warning. 
If the problem persists, 
determine if uplink is 
sending the current SI 
information table. 
Disable the warning if 
not using the table. 
No longer receiving 
Conditional Access 
Table. 
CAT timeout # Clear cat fault cleared   
DRT timeout # Set drt # timed out Cause:...

 
Chapter 6    Service and Maintenance  
 
 
268 78-4021470-01 Rev J 
Warning Message 
Type 
Message Cause/Remedy Description 
MCT Timeout # Set mct # is lost Cause: Uplink is not 
sending or is sending 
intermittently. 
Remedy: Clear warning. 
If the problem persists, 
determine if uplink is 
sending the current SI 
information table. 
Disable the warning if 
not using the table.  
No longer receiving 
Inband Control Table. 
MCT Timeout # Clear mct fault cleared   
ECT Timeout # Set ect # timed out...

 
 
 D9854 Receiver Alarm Messages 
 
78-4021470-01 Rev J 269 
 
Warning Message 
Type 
Message Cause/Remedy Description 
Memory Usage 
Secondary 
Set Excessive 
(stack/partition) 
memory usage 
Cause: Possible software 
issue. 
Remedy: Clear 
warnings, reset the unit, 
and notify customer 
service if the problem 
persists. 
Software exceeding 
allowable memory 
usage. 
Memory Usage 
Secondary 
Clear Normal 
(stack/partition) 
memory usage 
  
FPGA Code 
Version 
Set FPGA newer 
than SW, 
Supported=AAA,...

 
Chapter 6    Service and Maintenance  
 
 
270 78-4021470-01 Rev J 
Warning Message 
Type 
Message Cause/Remedy Description 
FW: Resource 
Use Host 
Clear Normal Level   
FW: Resource 
Use Second 
Set Memory or List 
Near Full 
Cause: Possible software 
issue. 
Remedy: Clear 
warnings, reset the unit, 
and notify customer 
service if the problem 
persists. 
Software exceeding 
allowable usage of 
internal constructs. 
FW: Resource 
Use Second 
Clear Normal Level   
Restore Failure 
Reason 
Set FTP...

 
 
 D9854 Receiver Alarm Messages 
 
78-4021470-01 Rev J 271 
 
Warning Message 
Type 
Message Cause/Remedy Description 
Restore Failure 
Reason 
Set Bad Content Cause: Import file may 
be corrupted, or from a 
different version of 
application software. 
Remedy: Verify that the 
correct import file is 
being used and was 
created by this product. 
Verify that the file 
structure has not been 
corrupted. If the 
problem persists, notify 
customer service. 
Item in import file is 
not valid for this...

 
 
78-4021470-01 Rev J 273 
 
If You Have Questions 
If you have technical questions, call Cisco Services for assistance. 
Follow the menu options to speak with a service engineer. 
Access your companys extranet site to view or order additional 
technical publications. For accessing instructions, contact the 
representative who handles your account. Check your extranet site 
often as the information is updated frequently.   
7 Chapter 7 
Customer Information  

 
 
78-4021470-01 Rev J 275 
 
A Appx auto letter 
Appendix A 
Technical Specifications 
Introduction 
This appendix contains the technical specifications for the D9854 
Advanced Program Receiver. 
Note: The technical specifications are subject to change without prior 
notice.  
 
 
In This Appendix 
 L-Band Input and Processing ............................................................ 276 
 Video Inputs/Outputs and Processing............................................ 280 
 Transport Stream...

 
Appendix A 
Technical Specifications 
276 78-4021470-01 Rev J 
L-Band Input and Processing 
General 
Parameter Specification 
System MPEG-2/DVB Compatible 
DVB-S EN 300 421, EN 300 468 
Demodulation DVB-S QPSK, DVB-S2 QPSK and 8PSK 
Number of RF Inputs 4 (only one active at a time) 
  
LNB LO Stability 
DVB-S and DVB-S2 
Symbol Rate Stability 
1 to 4.99 MSymbols/s ≤ ± 125 kHz 
5.0 to 9.99 MSymbols/s ≤ ± 1.0 MHz 
10.0 to 45 MSymbols/s ≤ ± 3.0 MHz 
 
Parameter Specification 
LNB Phase Noise 
Requirement...