Canyon Router CNP-WF514N1 User Manual

41 
2-5-5 Setup procedure for ‘L2TP’ 
 
 
 
Here are descriptions of every setup items: 
 
User ID (1):    Please input user ID (user name) assigned by your Internet 
service provider here. 
 
Password (2):    Please input the password assigned by your Internet service 
provider here. 
 
L2TP      Please input the IP address of PPTP gateway assigned by 
Gateway (3):     your Internet service provider here. 
 
MTU (4):    Please input the MTU value of your network connection here. If 
you don’t know, you...

42 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on other setup 
procedures, or click ‘Apply’ to reboot the router so the settings will take effect 
(Please wait for about 30 seconds while router is rebooting). 
If you want to reset all settings in this page back to previously-saved value, please 
click ‘Cancel’ button. 
 
2-5-6 Setup procedure for ‘Telstra Big Pond’ 
 
 
 
This setting only works when you’re using Telstra big pond’s network service in 
Australia. You need to...

43 
When you finish with all settings, click ‘Apply’ (5) button and the following message 
will be displayed on your web browser: 
 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on other setup 
procedures, or click ‘Apply’ to reboot the router so the settings will take effect 
(Please wait for about 30 seconds while router is rebooting). 
 
If you want to reset all settings in this page back to previously-saved value, please 
click ‘Cancel’ button. 
 
2-5-7 Setup procedure for...

44 
DNS Address (1):    Please input the IP address of DNS server provided by your 
service provider. 
 
Secondary        Please input the IP address of another DNS 
DNS Address (2):    server provided by your service provider, this is optional. 
 
 
 
 
 
 
After you finish with all settings, please click ‘Apply’ (3) button and the following 
message will be displayed on your web browser: 
 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on other setup 
procedures, or click...

45 
DynDNS (http://www.dyndns.org) 
TZO (http://www.tzo.com
) 
 
Please go to one of DDNS service provider’s webpage listed above, and get a free 
DDNS account by the instructions given on their webpage. 
 
 
 
Here are descriptions of every setup items: 
 
Dynamic DNS (1):    If you want to enable DDNS function, please select 
‘Enabled’; otherwise please select ‘Disabled’. 
 
Provider (2):       Select your DDNS service provider here. 
 
Domain  Name  (3):    Input the domain name you’ve obtained from...

46 
 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on other setup 
procedures, or click ‘Apply’ to reboot the router so the settings will take effect 
(Please wait for about 30 seconds while router is rebooting). 
 
If you want to reset all settings in this page back to previously-saved value, please 
click ‘Cancel’ button.  

47 
2-6 Wired LAN Configuration 
 
Before all computers using wired Ethernet connection (i.e. those computers connect 
to this router’s LAN port 1 to 4 by Ethernet cable) can communicate with each other 
and access internet, they must have a valid IP address. 
 
There are two ways to assign IP addresses to computers: static IP address (set the 
IP address for every computer manually), and dynamic IP address (IP address of 
computers will be assigned by router automatically. It’s recommended for most of...

48 
Please follow the following instructions to set wired LAN parameters: 
 
Please click ‘LAN’ menu on the left of web management interface, there are three 
setup groups here: ‘LAN IP’, ‘DHCP Server’, and ‘Static DHCP Leases Table’. Here are 
setup instructions for each of them: 
 
2-6-1 LAN IP section 
 
 
 
Here are descriptions of every setup items: 
 
IP address (1):      Please input the IP address of this router. 
 
Subnet Mask (2):     Please input subnet mask for this network. 
 
802.1d     If...

49 
2-6-2 DHCP Server 
 
 
 
These settings are only available when ‘DHCP Server’ in ‘LAN IP’ section is ‘Enabled’, 
and here are descriptions of every setup items: 
 
Lease Time (1):    Please choose a lease time (the duration that every 
computer can keep a specific IP address) of every IP 
address assigned by this router from dropdown menu. 
 
Start IP (2):        Please input the start IP address of the IP range. 
 
End IP (3):        Please input the end IP address of the IP range. 
 
Domain Name...

50 
2-6-3 Static DHCP Leases Table 
 
This function allows you to assign a static IP address to a specific computer 
forever, so you don’t have to set the IP address for a computer, and still enjoy the 
benefit of using DHCP server. Maximum 16 static IP addresses can be assigned 
here. 
 
(If you set ‘Lease Time’ to ‘forever’ in ‘DHCP Server’ section, you can also assign 
an IP address to a specific computer permanently, however, you will not be able 
to assign a certain IP address to a specific...