Canyon Router CNP-WF514N1 User Manual

81 
After you finish with all settings, please click ‘save’ button (i), you’ll be brought back 
to previous menu, and the rule you just set will appear in current QoS table; if you 
did anything wrong, you’ll get an error message when you click ‘Save’ button, 
please correct your input by the instructions given by the error message. 
 
If you want to erase all values you just entered. Click ‘Reset’  

82 
3-2 Network Address Translation (NAT) 
 
Network address translations solve the problem if sharing a single IP address to 
multiple computers. Without NAT, all computers must be assigned with a valid 
Internet IP address to get connected to Internet, but Internet service providers only 
provide very few IP addresses to every user. Therefore it’s necessary to use NAT 
technology to share a single Internet IP address to multiple computers on local 
network, so everyone can get connected to Internet....

83 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on other setup 
procedures, or click ‘Apply’ to reboot the router so the settings will take effect 
(Please wait for about 30 seconds while router is rebooting). 
 
3-2-2 Port Forwarding 
 
This function allows you to redirect a single port or consecutive ports of Internet IP 
address to the same port of the IP address on local network. The port number(s) of 
Internet IP address and private IP address (the IP address on local...

84 
Enable Port        Check this box to enable port mapping, 
Forwarding (1):      and uncheck this box to disable port mapping. 
 
Private IP (2):    Input the IP address of the computer on local network 
which provides internet service. 
 
Computer  Name  (3):  Pull down the menu and all the computers connected to the 
router will be listed here. You can easily to select the 
computer name without checking the IP address of the 
computer. 
 
Type (4):    Select the type of connection, TCP or UDP. If...

85 
After you finish with all settings, please click ‘Apply’ (13) button and the following 
message will be displayed on your web browser: 
 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on other setup 
procedures, or click ‘Apply’ to reboot the router so the settings will take effect 
(Please wait for about 30 seconds while router is rebooting). 
 
If you want to reset all settings in this page back to previously-saved value, please 
click ‘Cancel’ button. 
 
3-2-3 Virtual...

86 
Here are descriptions of every setup items: 
 
Enable Virtual      Check this box to enable virtual server, and uncheck 
Server (1):        this box to disable virtual server. 
 
Private IP (2):      Input the IP address of the computer which provides 
     Internet service. 
 
Computer  Name  (3):  Pull down the menu and all the computers connected to the 
router will be listed here. You can easily to select the 
computer name without checking the IP address of the 
computer. 
 
Private Port (4):...

87 
Delete All (12):      Delete all mappings existed in virtual server table. 
 
Reset (13):        Unselect all mappings. 
 
After you finish with all settings, please click ‘Apply’ (14) button and the following 
message will be displayed on your web browser: 
 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on other setup 
procedures, or click ‘Apply’ to reboot the router so the settings will take effect 
(Please wait for about 30 seconds while router is rebooting). 
 
If you...

88 
Here are descriptions of every setup items: 
 
Enable (1):  Check this box to enable special applications and uncheck 
this box to disable virtual server. 
 
IP Address (2):    Input the IP address of the computer which you want to 
open the ports. 
 
Computer  Name  (3):  Pull down the menu and all the computers connected to the 
router will be listed here. You can easily to select the 
computer name without checking the IP address of the 
computer. 
 
TCP  Port  to  Open  (4):    This is the out...

89 
Delete (11):      Please select a special application by clicking 
    the ‘Select’ box of the mapping, then click ‘Delete Selected’ 
button to remove the setting. If there’s no setting here, this 
button will be grayed out. 
 
Delete All (12):      Delete all settings existed in trigger port table. 
 
Reset (13):        Unselect all settings. 
 
Note: Only one LAN client can use a particular special application at a time. 
 
After you finish with all settings, please click ‘Apply’ (14) button and...

90 
 
 
There is only one option in this page, please select ‘Enable’ or ‘Disable’ to enable or 
disable UPnP function, then click ‘Apply’ button, and the following message will be 
displayed on your web browser: 
 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on other setup 
procedures, or click ‘Apply’ to reboot the router so the settings will take effect 
(Please wait for about 30 seconds while router is rebooting). 
 
If you want to reset all settings in this page back to...