Canyon Router CNP-WF514N1 User Manual

31 
Confirmed       Please input new password here again. 
Password (3):   
 
When you finish, click ‘Apply’. If you want to keep original password unchanged, 
click ‘Cancel’. 
If the password you typed in ‘New Password’ (2) and ‘Confirmed Password’ (3) field 
are not the same, you’ll see the following message: 
 
 
 
Please retype the new password again when you see above message. 
If you see the following message: 
 
 
 
It means the content in ‘Current Password’ field is wrong, please click ‘OK’ to go...

32 
Please use new password to enter web management interface again, and you should 
be able to login with new password. 
 
2-4-3 Remote Management 
 
This router does not allow management access from Internet, to prevent possible 
security risks (especially when you defined a weak password, or didn’t change 
default password). However, you can still management this router from a specific IP 
address by enabling the ‘Remote Management’ Function. 
 
To do so, please follow the following instructions:...

33 
 
 
 
Press ‘Continue’ to save the settings made and back to web management interface; 
press ‘Apply’ to save the settings made and restart the router so the settings will 
take effect after it reboots. 
 
NOTE: When you want to manage this router from another computer 
on internet, you have to input the IP address and port number of this 
router. If your Internet service provider assigns you with a static IP 
address, it will not be a problem; but if the IP address your service 
provider assigns to...

34 
2-5 Setup Internet Connection (WAN Setup) 
 
Internet connections setup can be done by using ‘Quick Setup’ menu described in 
chapter 2-3. However, you can setup WAN connections up by using WAN 
configuration menu. You can also set advanced functions like DDNS (Dynamic DNS) 
here. 
 
To start configuration, please follow the following instructions: 
 
Please click ‘WAN’ menu on the left of web management interface, and the following 
message will be displayed on your web browser: 
 
Please select an...

35 
2-5-1 Setup procedure for ‘Dynamic IP’ 
 
 
 
Here are descriptions of every setup items: 
 
Host Name (1):    Please input host name of your computer, this is optional, 
a n d  o n l y  r e q u i r e d  i f  y o u r  s e r v i c e  p r o v i d e r  a s k s  y o u  t o  d o  s o .    
 
MAC Address (2):    Please input MAC address of your computer, if your service 
provider only permits computer with certain MAC address 
to access internet. If you’re using the computer which used 
to connect to...

36 
setup, or click ‘Apply’ to reboot the router so the settings will take effect (Please wait 
for about 30 seconds while router is rebooting). 
 
2-5-2 Setup procedure for ‘Static IP’ 
 
 
 
Here are descriptions of every setup items: 
 
IP address assigned    Please input IP address assigned by your service   
by your Service        provider. 
Provider (1):   
 
Subnet Mask (2):    Please input subnet mask assigned by your service 
provider  
 
Service Provider        Please input the IP address of...

37 
If you want to reset all settings in this page back to previously-saved value, please 
click ‘Cancel’ button. 
 
2-5-3 Setup procedure for ‘PPPoE’ 
 
 
 
Here are descriptions of every setup items: 
 
User Name (1):    Please input user name assigned by your Internet service 
provider here. 
 
Password (2):    Please input the password assigned by your Internet 
service provider here. 
 
Service Name (3):    Please give a name to this Internet service, this is optional 
 
MTU  (4):    Please input...

38 
Connect On-Demand – Only connect when you want to surf the 
Internet. “Idle Time Out” is set to stop the connection when the 
network traffic is not sending or receiving after an idle time. 
 
Manual – After you have selected this option, you will see the
 
“Connect” button and “Disconnect” button, click “’Connect” 
and the router will connect to the ISP. If you want to stop the
 
connection, please click “Disconnect” button. 
 
Idle Time Out (6):    If you have selected the connection type to...

39 
 
 
Select the type of how you obtain IP address from your service provider here. You 
can choose ‘Obtain an IP address automatically’ (equal to DHCP, please refer to 
‘Cable Modem’ section above), or ‘Use the following IP address’ (i.e. static IP 
address) 
WAN interface settings must be correctly set, or the Internet connection will fail 
even those settings of PPTP settings are correct. Please contact your Internet 
service provider if you don’t know what you should fill in these fields. 
Now...

40 
PPTP Gateway (3):    Please input the IP address of PPTP gateway assigned by 
your Internet service provider here. 
 
Connection ID (4):    Please input the connection ID here, this is optional and you 
can leave it blank. 
 
MTU  (5):    Please input the MTU value of your network connection here. 
If you don’t know, you can use default value. 
 
BEZEQ-ISRAEL (6):  If you are connecting to the BEZEQ network in Israel. 
Please enable this function. 
 
Connection        Please select the connection...