Canyon Router CNP-WF514N1 User Manual

							31 
Confirmed       Please input new password here again. 
Password (3):   
 
When you finish, click ‘Apply’. If you want to keep original password unchanged, 
click ‘Cancel’. 
If the password you typed in ‘New Password’ (2) and ‘Confirmed Password’ (3) field 
are not the same, you’ll see the following message: 
 
 
 
Please retype the new password again when you see above message. 
If you see the following message: 
 
 
 
It means the content in ‘Current Password’ field is wrong, please click ‘OK’ to go 
back to previous menu, and try to input current password again. 
If the current and new passwords are correctly entered, after you click ‘Apply’, you’ll 
be prompted to input your new password: 
  
						

							32 
Please use new password to enter web management interface again, and you should 
be able to login with new password. 
 
2-4-3 Remote Management 
 
This router does not allow management access from Internet, to prevent possible 
security risks (especially when you defined a weak password, or didn’t change 
default password). However, you can still management this router from a specific IP 
address by enabling the ‘Remote Management’ Function. 
 
To do so, please follow the following instructions: 
 
Please click ‘System’ menu on the left of web management interface, then click 
‘Remote Management’, and the following message will be displayed on your web 
browser: 
 
 
 
Here are descriptions of every setup items: 
 
Host Address (1):    Input the IP address of the remote host you wish to initiate 
a management access.   
 
Port (2):    You can define the port number this router should expect 
an incoming request. If you’re providing a web service 
(default port number is 80), you should try to use other 
port number. You can use the default port setting ‘8080’, or 
something like ‘32245’ or ‘1429’. (Any integer between 1 
and 65534) 
 
Enabled (3):  Select the field to start the configuration. 
 
When you finish with all settings, click ‘Apply’, and you’ll see the following message 
displayed on web browser: 
123
4 
						

							33 
 
 
 
Press ‘Continue’ to save the settings made and back to web management interface; 
press ‘Apply’ to save the settings made and restart the router so the settings will 
take effect after it reboots. 
 
NOTE: When you want to manage this router from another computer 
on internet, you have to input the IP address and port number of this 
router. If your Internet service provider assigns you with a static IP 
address, it will not be a problem; but if the IP address your service 
provider assigns to you will vary every time you establish an internet 
connection, this will be a problem.   
 
Please either ask your service provider to give you a static IP 
address, or use dynamic IP to host name mapping services like 
DDNS. Please refer to chapter 2-5-8 ‘DDNS client’ for details. 
NOTE: Default port number the web browser will use is ‘80’. If the 
‘Port’ setting in this page is not ‘80’, you have to assign the port 
number in the address bar of web browser manually. For example, if 
the IP address of this router is 1.2.3.4, and the port number you set is 
8888, you have to input following address in the address bar of web 
browser: 
 
http://1.2.3.4:8888  
						

							34 
2-5 Setup Internet Connection (WAN Setup) 
 
Internet connections setup can be done by using ‘Quick Setup’ menu described in 
chapter 2-3. However, you can setup WAN connections up by using WAN 
configuration menu. You can also set advanced functions like DDNS (Dynamic DNS) 
here. 
 
To start configuration, please follow the following instructions: 
 
Please click ‘WAN’ menu on the left of web management interface, and the following 
message will be displayed on your web browser: 
 
Please select an Internet connection method depend on the type of connection 
you’re using. You can either click the connection method on the left (1) or right (2). 
If you select the connection method on the right, please click ‘More Configuration’ 
button after a method is selected. 
 
 
 
Dynamic IP      - Please go to section 2-5-1 
Static IP        - Please go to section 2-5-2 
PPPoE        - Please go to section 2-5-3 
PPTP        - Please go to section 2-5-4 
L2TP        - Please go to section 2-5-5 
Telstra Big Pond    - Please go to section 2-5-6 
DNS         - Please go to section 2-5-7 
DDNS        - Please go to section 2-5-8 
 
1
2 
						

							35 
2-5-1 Setup procedure for ‘Dynamic IP’ 
 
 
 
Here are descriptions of every setup items: 
 
Host Name (1):    Please input host name of your computer, this is optional, 
a n d  o n l y  r e q u i r e d  i f  y o u r  s e r v i c e  p r o v i d e r  a s k s  y o u  t o  d o  s o .    
 
MAC Address (2):    Please input MAC address of your computer, if your service 
provider only permits computer with certain MAC address 
to access internet. If you’re using the computer which used 
to connect to Internet via cable modem, you can simply 
press ‘Clone Mac address’ button to fill the MAC address 
field with the MAC address of your computer,  
 
After you finish with all settings, please click ‘Apply’ (3); if you want to remove and 
value you entered, please click ‘Cancel’. 
 
After you click ‘Apply’, the following message will be displayed on your web browser: 
 
 
 
Please click ‘Continue’ (1) to back to previous setup menu; to continue on router 
1 
2 
3  
						

							36 
setup, or click ‘Apply’ to reboot the router so the settings will take effect (Please wait 
for about 30 seconds while router is rebooting). 
 
2-5-2 Setup procedure for ‘Static IP’ 
 
 
 
Here are descriptions of every setup items: 
 
IP address assigned    Please input IP address assigned by your service   
by your Service        provider. 
Provider (1):   
 
Subnet Mask (2):    Please input subnet mask assigned by your service 
provider  
 
Service Provider        Please input the IP address of DNS 
Gateway Address (3):      server provided by your service provider. 
 
After you finish with all settings, please click ‘Apply’ (4) button and the following 
message will be displayed on your web browser: 
 
Please click ‘Continue’ to back to previous setup menu; to continue on other setup 
procedures, or click ‘Apply’ to reboot the router so the settings will take effect 
(Please wait for about 30 seconds while router is rebooting). 
1 
2 
3 
4 
						

							37 
If you want to reset all settings in this page back to previously-saved value, please 
click ‘Cancel’ button. 
 
2-5-3 Setup procedure for ‘PPPoE’ 
 
 
 
Here are descriptions of every setup items: 
 
User Name (1):    Please input user name assigned by your Internet service 
provider here. 
 
Password (2):    Please input the password assigned by your Internet 
service provider here. 
 
Service Name (3):    Please give a name to this Internet service, this is optional 
 
MTU  (4):    Please input the MTU value of your network connection here. 
If you don’t know, you can use default value. 
 
Connection        Please select the connection type of Internet connection   
Type (5):    you wish to use. 
Continuous – The connection will be kept always on. If the 
connection is interrupted, the router will re-connect 
automatically. 
1 
2 
4  3 
5
6
7  
						

							38 
Connect On-Demand – Only connect when you want to surf the 
Internet. “Idle Time Out” is set to stop the connection when the 
network traffic is not sending or receiving after an idle time. 
 
Manual – After you have selected this option, you will see the
 
“Connect” button and “Disconnect” button, click “’Connect” 
and the router will connect to the ISP. If you want to stop the
 
connection, please click “Disconnect” button. 
 
Idle Time Out (6):    If you have selected the connection type to 
“Connect-On-Demand”, please input the idle time out. 
 
After you finish with all settings, please click ‘Apply’ (7) button and the following 
message will be displayed on your web browser: 
 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on other setup 
procedures, or click ‘Apply’ to reboot the router so the settings will take effect 
(Please wait for about 30 seconds while router is rebooting). 
 
If you want to reset all settings in this page back to previously-saved value, please 
click ‘Cancel’ button. 
 
2-5-4 Setup procedure for ‘PPTP’ 
 
PPTP requires two kinds of setting: WAN interface setting (setup IP address) and 
PPTP setting (PPTP user name and password). Here we start from WAN interface 
setting: 
  
						

							39 
 
 
Select the type of how you obtain IP address from your service provider here. You 
can choose ‘Obtain an IP address automatically’ (equal to DHCP, please refer to 
‘Cable Modem’ section above), or ‘Use the following IP address’ (i.e. static IP 
address) 
WAN interface settings must be correctly set, or the Internet connection will fail 
even those settings of PPTP settings are correct. Please contact your Internet 
service provider if you don’t know what you should fill in these fields. 
Now please go to PPTP settings section: 
 
 
 
Here are descriptions of every setup items: 
 
User  Name  (1):    Please input user ID (user name) assigned by your Internet 
service provider here. 
 
Password (2):    Please input the password assigned by your Internet 
service provider here. 
 
1
2
3 
4 
5 
7 
8 
9
6  
						

							40 
PPTP Gateway (3):    Please input the IP address of PPTP gateway assigned by 
your Internet service provider here. 
 
Connection ID (4):    Please input the connection ID here, this is optional and you 
can leave it blank. 
 
MTU  (5):    Please input the MTU value of your network connection here. 
If you don’t know, you can use default value. 
 
BEZEQ-ISRAEL (6):  If you are connecting to the BEZEQ network in Israel. 
Please enable this function. 
 
Connection        Please select the connection type of Internet connection 
type (7):    you wish to use, please refer to section 2-5-3 for detailed 
descriptions. 
 
Idle Time Out (8):    Please input the idle time out of Internet connection you 
wish to use, and refer to section 2-5-3 for detailed 
descriptions. 
 
When you finish with all settings, please click ‘Apply’ (9) button and the following 
message will be displayed on your web browser: 
 
 
 
Please click ‘Continue’ to back to previous setup menu; to continue on other setup 
procedures, or click ‘Apply’ to reboot the router so the settings will take effect 
(Please wait for about 30 seconds while router is rebooting). 
 
If you want to reset all settings in this page back to previously-saved value, please 
click ‘Cancel’ button.