Canyon Router CNP-WF514N1 User Manual

							21 
2-3-2 Setup procedure for ‘Fixed-IP xDSL’: 
 
 
Here are descriptions of every setup items: 
 
IP address        Please input IP address assigned by your service provider. 
assigned by your       
Service Provider (1):     
 
Subnet Mask (2):    Please input subnet mask assigned by your service provider   
 
DNS address (3):    Please input the IP address of DNS server provided by your 
service provider. 
 
Service Provider      Please input the IP address of DNS server provided by your   
Gateway Address (4):    service provider. 
 
 
 
 
 
When you finish with all settings, press ‘OK’ (5); if you want to go back to previous 
menu, click ‘Back’. 
 
 
 
 
 
 
1 
2 
3 
4 
5 
NOTE: You can choose this Internet connection method if your 
service provider assigns a fixed IP address (also know as static 
address) to you, and not using DHCP or PPPoE protocol. Please 
contact your service provider for further information. 
You must use the addresses provided by your Internet service 
provider, wrong setting value will cause connection problem.    
						

							22 
2-3-3 Setup procedure for ‘PPPoE xDSL’: 
 
 
 
Here are descriptions of every setup items: 
 
User Name (1):    Please input user name assigned by your Internet service 
provider here. 
 
Password (2):    Please input the password assigned by your Internet 
service provider here. 
 
Service Name (3):    Please give a name to this Internet service, this is optional 
 
MTU  (4):    Please input the MTU value of your network connection here. 
If you don’t know, you can use default value. 
 
Connection        Please select the connection type of Internet connection 
Type (5):    you wish to use (detailed explanation listed below). 
 
Idle Time Out (6):    Please input idle time out, (detailed explanation listed 
below). 
 
When you finish with all settings, please click ‘OK’ (7); if you want to go back to 
previous menu, click ‘Back’. 
 
 
1 
2 
4  3 
5 
6 
7  
						

							23 
 
 
 
 
 
 
 
 
 
 
 
 
 
2-3-4 Setup procedure for ‘PPTP xDSL’: 
 
PPTP xDSL requires two kinds of setting: WAN interface setting (setup IP address) 
and PPTP setting (PPTP user name and password). Here we start from WAN interface 
setting: 
 
 
 
Select the type of how you obtain IP address from your service provider here. You 
can choose ‘Obtain an IP address automatically’ (equal to DHCP, please refer to 
‘Cable Modem’ section above), or ‘Use the following IP address’ (i.e. static IP 
address).  
WAN interface settings must be correctly set, or the Internet connection will fail 
even those settings of PPTP settings are correct. Please contact your Internet 
service provider if you don’t know what you should fill in these fields. 
Now please go to PPTP settings section: 
 
MTU - Please use default value if you don’t know what it is, or ask 
your service provider for a proper value. 
 
Connection Type - There are 3 options: ‘Continuous’ - keep internet 
connection alive, do not disconnect, connect on Demand - only 
connects to Internet when there’s a connect attempt, and ‘Manual’ - 
only connects to Internet when ‘Connect’ button on this page is 
pressed, and disconnects when ‘Disconnect button is pressed. 
 
Idle Time Out: Specify the time to shutdown internet connect after no 
internet activity is detected by minute. This option is only available 
when connection type is ‘Connect on Demand’.  
						

							24 
 
 
Here are descriptions of every setup items: 
User  Name  (1):    Please input user ID (user name) assigned by your Internet 
service provider here. 
 
Password (2):    Please input the password assigned by your Internet 
service provider here. 
 
PPTP    Please input the IP address of PPTP gateway assigned by 
Gateway (3):    your Internet service provider here. 
 
Connection        Please input the connection ID here, this is optional and 
ID (4):          you can leave it blank. 
 
MTU  (5):    Please input the MTU value of your network connection here. 
If you don’t know, you can use default value. 
 
BEZEQ-ISRAEL (6):  Setting item ‘BEZEQ-ISRAEL’ is only required to Check if 
you’re using the service provided by BEZEQ network in 
Israel.  
 
Connection        Please select the connection type of Internet connection 
type (7):    you wish to use, please refer to last section for detailed 
descriptions. 
 
 
 
1 
2
3 
4 
5 
6 
7 
9 
8  
						

							25 
Idle Time        Please input the idle time out of Internet connection 
Out (8):    you wish to use, and refer to last section for detailed 
descriptions. 
 
When you finish with all settings, please click ‘OK (9); if you want to go back to 
previous menu, click ‘Back’. 
 
2-3-5 Setup procedure for ‘L2TP xDSL’: 
 
L2TP is another popular connection method for xDSL and other Internet connection 
types, and all required setting items are the same with PPTP connection. 
 
Like PPTP, there are two kinds of required setting, we’ll start from ‘WAN Interface 
Settings’: 
 
 
 
Please select the type of how you obtain IP address from your service provider here. 
You can choose ‘Obtain an IP address automatically’ (equal to DHCP, please refer to 
‘Cable Modem’ section above), or ‘Use the following IP address’ (equal to static IP 
address, please refer to ‘PPPoE xDSL’ section above).   
WAN interface settings must be correctly set, or the Internet connection will fail 
even those settings of PPTP settings are correct. Please contact your Internet 
service provider if you don’t know what you should fill in these fields. 
 
 
 
 
 
  
						

							26 
Now please go to L2TP settings section: 
 
 
 
Here are descriptions of every setup items: 
 
User Name (1):      Please input user ID (user name) assigned by your    
     Internet service provider here. 
 
Password (2):    Please input the password assigned by your Internet 
service provider here. 
 
L2TP Gateway (3):    Please input the IP address of PPTP gateway assigned by 
your Internet service provider here. 
 
MTU  (4):    Please input the MTU value of your network connection here. 
If you don’t know, you can use default value. 
 
Connection        Please select the connection type of Internet connection 
type (5):    you wish to use, please refer to last section for detailed 
descriptions. 
 
Idle Time        Please input the idle time out of Internet    connection 
Out (6):    you wish to use, and refer to last section for detailed 
descriptions. 
 
When you finish with all settings, please click ‘OK (7); if you want to go back to 
previous menu, click ‘Back’. 
 
 
1 
2 
4  3 
5 
7 6  
						

							27 
2-3-6 Setup procedure for ‘Telstra Big Pond’: 
 
 
 
This setting only works when you’re using Telstra big pond’s network service in 
Australia. You need to input: 
User Name (1):      Please input the user name assigned by Telstra. 
 
Password (2):      Please input the password assigned by Telstra. 
 
User decide login       Check this box to choose login server by yourself. 
server manually (3):   
 
Login Server(4):    Please input the IP address of login server here. 
 
When you finish with all settings, click ‘OK (5); if you want to go back to previous 
menu, click ‘Back’. 
 
When all settings are finished, you’ll see the following message displayed on your 
web browser: 
 
 
 
 
1
2
3 
4 
5  
						

							28 
Please click ‘Apply’ button to prepare to restart the router, and you’ll see this 
message: 
 
 
 
Please wait for about 30 seconds, then click ‘OK!’ button. You’ll be back to router 
management interface again, and the router is ready with new settings.  
						

							29 
2-4 Basic Setup 
 
In this chapter, you’ll know how to change the time zone, password, and remote 
management settings. Please start your web browser and log onto router web 
management interface, then click ‘General Setup’ button on the left, or click 
‘General Setup’ link at the upper-right corner of web management interface. 
 
 
 
 
2-4-1 Time zone and time auto-synchronization 
 
Please follow the following instructions to set time zone and time 
auto-synchronization parameters: 
 
Please click ‘System’ menu on the left of web management interface, then click 
‘Time Zone’, and the following message will be displayed on your web browser: 
Please select time zone at ‘Set time zone’ drop-down list, and input the IP address 
or host name of time server. If you want to enable daylight savings setting, please 
check ‘Enable Function’ box, and set the duration of daylight setting. When you 
finish, click ‘Apply’. You’ll see the following message displayed on web browser: 
 
HERE!  
						

							30 
 
 
Press ‘Continue’ to save the settings made and back to web management interface; 
press ‘Apply’ to save the settings made and restart the router so the settings will 
take effect after it reboots. 
 
 
 
 
2-4-2 Change management password 
 
Default password of this router is 1234, and it’s displayed on the login prompt when 
accessed from web browser. There’s a security risk if you don’t change the default 
password, since everyone can see it. This is very important when you have wireless 
function enabled. 
 
To change password, please follow the following instructions: 
 
Please click ‘System’ menu on the left of web management interface, then click 
‘Password Settings’, and the following message will be displayed on your web 
browser: 
 
 
Here are descriptions of every setup items: 
Current     Please input current password here. 
Password (1):   
 
New Password (2):    Please input new password here. 
NOTE: You can refer to the instructions given in last chapter: ‘Using 
Quick Setup’, for detailed descriptions on time zone settings. 
1
2
3