Canon scanner imageFORMULA DRX10C User Manual

4-8
Chapter 4   Other Functions
■Locking the Keys (Invalidate Key Function)
Press and hold the [Enter] key for approximately 5 seconds 
to display the Invalidate Key setting.
Press the [ ] key to select [OK], and press [Enter] to 
disable the keys.
IMPORTANT
 To unlock the keys, press and hold the [Enter] key again for 
approximately 5 seconds, or turn the scanner OFF and back 
ON.
 After turning the scanner OFF, wait at least 10 seconds before 
turning it back ON.
■Imprinter (Optional)
The scanner...

4-9
Chapter 4   Other Functions
3.User Mode
The User Mode provides the user with the capability to change certain scanner functions.
User Mode Operating Procedure
User Mode operations are controlled by the following 
procedure.
Hint
Operating procedures differ according to User Mode function. For 
details, refer to the indicated pages.
1.Press the Menu key on  the control panel.
The User Mode is activated.
2.Press the [ ] and [ ] keys to select the User Mode 
function.
The User Mode functions are...

4-10
Chapter 4   Other Functions
3.Press [Enter].
The current setting is indicated by blinking square brackets 
[ ].
4.Press the [ ] or [ ] key to select [ON] or [OFF], and 
press [Enter] to accept the selection.
Enter Key 

4-11
Chapter 4   Other Functions
4.User Mode Functions
The following functions are available in the User Mode.
■Buzzer (Beeper) Control Setting
The beeper (“buzzer”) sounds  when you press the control 
panel keys and when a  scanning error occurs.
ON2:  The beeper sounds when a scanner error occurs.
ON1:  The beeper sounds when a scanner error occurs, and 
when a control panel key is pressed.
OFF:  The beeper never sounds.
■Double-Feed Control Setting
Select whether double-feed dete ction is enabled...

4-12
Chapter 4   Other Functions
Hint
Feeding a document longer the maximum detectable page size 
for Auto Detection causes a paper jam indication, and transport 
stops.
■Continuous Manual Feeding Mode Setting
This mode disables automatic feeding by the pickup roller, 
so that the loaded document stack must be fed by hand one 
sheet at a time by the operator. (See “Continuous Manual 
Feeding Mode” on p. 3-13.)
ON: The pickup roller is disabled.
OFF: Documents are fed by the pickup roller.
■Stand-by Mode...

4-13
Chapter 4   Other Functions
■Frame Detection Error Mode Setting
If set to ON, an error message is displayed when the 
correct paper size of the image cannot be detected.
If detection fails, the sensor may have failed.
IMPORTANT
 When the error message is displayed, clean both the sensor 
glass and the reading glass. (See “Cleaning the Glass” on 
p. 5-5.)
 If an image cannot be scanned normally after the glass has 
been cleaned, the glass may have been scratched. In such a 
case, contact the sales...

4-14
Chapter 4   Other Functions
■Imprinter Test
When the optional imprinter is installed, this function 
executes a test printing of the imprinter. (See “Performing 
an Imprinter Test” on p. 5-20.)
■Cleaning Mode
This function executes roller cleaning using a cleaning 
sheet. (See “Cleaning Rollers with a Cleaning Sheet” on 
p. 5-4.) 

Chapter 5   Maintenance
1. Regular Maintenance....................................... 5-2
Cleaning the Scanner............................................5-2
Cleaning the Glass and Rollers.............................5-3
Opening and Closing the Upper Unit ....................5-3
Cleaning Rollers with a Cleaning Sheet ................5-4
Cleaning the Glass ................................................5-5
Cleaning the Platen Rollers...................................5-6
Cleaning the Pickup and Feed...

5-2
Chapter 5   Maintenance
1.Regular Maintenance
To maintain scanning quality, routinely clean the scanner as described below.
CAUTION
 Do not use spray cleaners to clean the scanner. Precision mechanisms may get wet and malfunction.
 Never use paint thinner, alcohol, or other organic solvents to clean the scanner. Such solvents may deform or discolor the exterior of the 
scanner, and cause other damage.
 When opening and closing the upper unit, be careful not to get you fingers caught, as this may...

5-3
Chapter 5   Maintenance
Cleaning the Glass and Rollers
If scanned images contain spots or documents become dirty 
after scanning, the scanning glass or transport rollers inside 
the scanner may be dirty.
The locations of the main glass and rollers are as follows.
For instructions on cleaning the glass and rollers, refer to the 
following pages.
Scanning Glass and Sensor Glass (See “Cleaning the 
Glass” on p. 5-5)
Platen Rollers (See “Cleaning the Platen Rollers” on 
p. 5-6)
Pickup and Feed Rollers...