Canon scanner imageFORMULA DRX10C User Manual

Chapter 2   Setup
1. Setup Procedures ............................................ 2-2
2. Installation Requirements ................................ 2-3
3. Software Installation ........................................ 2-4
About the Setup Menu ..........................................2-4
4. Connecting the Scanner to the Computer ....... 2-6
Interface Connector Locations ..............................2-6
Connecting the Scanner to the Computer .............2-6
5. Turning the Power ON 
(Scanner...

2-2
Chapter 2   Setup
1.Setup Procedures
Perform the following setup procedures to prepare the scanner for use.
Step 1: Confirm the installation requirements. (See p. 2-3)
Step 2: Install the Software. (See p. 2-4)
Step 3: Connect the scanner to the computer. (See p. 2-6)
Step 4: Turn the power ON (Scanner recognition). (See p. 2-9)
IMPORTANT
 Be sure to install the software before connecting the scanner 
to the computer.
 If you connect the scanner to the computer before installing 
the software, a...

2-3
Chapter 2   Setup
2.Installation Requirements
To use the DR-X10C, your computer must satisfy the following system requirements.
■Operating System:
 Microsoft Windows 2000 Professional SP4 or later
 Microsoft Windows XP Professional SP2 or later
 Microsoft Windows XP Home Edition SP2 or later
 Microsoft Windows XP Professional x64 Edition
 Microsoft Windows Vista Home basic, Home premium, 
Business, Ultimate or Enterprise 
Hint
Microsoft Windows Vista has 32- and 64-bit versions.
■Computer...

2-4
Chapter 2   Setup
3.Software Installation
This section describes how to install the software.
About the Setup Menu
When you insert the included Setup disc into the computer’s 
CD drive, the menu shown below should appear. If the menu 
does not appear, use Explorer to access the CD drive and 
execute the file “SETUP.EXE”.
IMPORTANT
 As always when installing software, log in using an account with 
Administrator privileges.
 When using Windows Vista, the “User Account Control” dialog 
box may appear....

2-5
Chapter 2   Setup
■The Custom Installation Screen
This screen appears when you click “Custom Installation” 
on the Menu screen. Select the check boxes next to the 
software that you want to install. 
Click [Install] to install the selected software.
■The Read Manual Screen
From this screen you can select one of the supplied 
electronic manuals to read: the Easy Start Guide (a printed 
copy is also supplied), the Reference Guide, the User 
Manual (this manual), or the CapturePerfect 3.0 
Operation...

2-6
Chapter 2   Setup
4.Connecting the Scanner to the Computer
There are two methods for connecting the DR-X10C scanner to a computer: a USB connection to a standard USB port built in to 
the computer, or SCSI connection to a SCSI card installed in an expansion slot of the computer. Select the method that is best suited 
to your computer environment.
Interface Connector Locations
The USB port and SCSI connector are located on the scanner 
as shown below.
IMPORTANT
 Do not connect both USB and SCSI cables...

2-7
Chapter 2   Setup
3.Use the supplied USB cable to connect the scanner 
to the computer.
Connect the square plug (Type B) of the USB cable to the 
scanner.
■Using a SCSI Connection
IMPORTANT
Make sure that the computer is turned OFF before connecting 
the SCSI cable. If the cable is connected while the computer is 
on, the scanner may not be properly recognized by the 
computer.
1.Shut down Windows and turn the computer’s power 
OFF.
2.Connect the supplied power cord into the power 
connector on the...

2-8
Chapter 2   Setup
IMPORTANT
Observe the following when connecting the scanner with other 
devices in a “daisy chain”.
 The SCSI ID of the scanner is set to “SCSI ID = 2” by default. 
When using a daisy-chain configuration with other SCSI 
devices, set the DIP switches so that SCSI ID numbers are not 
duplicated in the system.
 The DR-X10C scanner incorporates a SCSI terminator which 
is permanently set to ON. When using a daisy-chain 
configuration with other SCSI devices, make sure that the DR-
X10C...

2-9
Chapter 2   Setup
5.Turning the Power ON (Scanner Recognition)
When you turn ON the computer and the scanner, the Windows Plug and Play function recognizes the scanner and automatically 
installs the required device driver.
About the Power Switch
When the power switch (located at the lower left side of the 
front of the scanner) is turned ON, the Document Feed Tray 
opens automatically. (See p. 3-7.)
IMPORTANT
 When connecting the scanner to the computer using a SCSI 
cable, be sure to turn ON the...

2-10
Chapter 2   Setup
Hint
 With Windows Vista, installation proceeds automatically 
regardless of the displayed “Check here for status” balloon 
help. 
You can click “Check here for status” to display the installation 
progress.
 With Windows XP and Vista, a message appears when 
installation is finished.

 Windows Vista The DR-X10C device driver is installed in Device Manager 
under [Imaging Devices] as [CANON DR-X10C USB] or 
[CANON DR-X10C SCSI].
 From the Control Panel, you can display the Device...