Canon scanner imageFORMULA DR6030C User Manual

Using the Scanner25
Chapter 2
Installing the Document Eject Guide
When scanning a document that is particularly thin or particularly long, it 
could droop down over the edge of the document eject tray extension and 
become jammed in the scanner. Avoid this problem by attaching the document 
eject guide.
1.Open the document eject tray extention toward you.
2.Attach the document eject guide in the order ➀, ➁ as shown.
3.Press the document eject guide to attach it to document eject tray extention. 

26Using the Scanner
4.To remove the document eject guide, lift the document eject tray extension a 
little and unhook the document eject guide.
5.Reverse the procedure for attaching the document eject guide to remove it. 

Using the Scanner27
Chapter 2
3. Placing Documents
There are two methods for paper separation, called the page separation mode 
and bypass mode for feeding documents. Feeding documents continuously 
from a stack of documents placed in the feed tray is called the page separation 
mode. Feeding documents one sheet at a time by hand or feeding multiple 
sheet documents, such as invoices that are attached at one end, is called the 
bypass mode. The document feed method can be switched by moving the feed...

28Using the Scanner
2.Straighten the edges of the stack of documents to be scanned.
CAUTION
• Do not place the documents on top of the scanner to align them. 
Doing so may cause a malfunction.
• Be careful when placing a document in the scanner. It is 
possible to cut your hand on the edge of a sheet of paper.
3.Set the document guides so they are wider than the document to be scanned.
IMPORTANT
When scanning small or short documents, adjust the document guides 2 to the 
edges of the documents.
4.Place...

Using the Scanner29
Chapter 2
IMPORTANT
There is a load limit mark ( ) on the document guides. Do not stack 
documents higher than this mark (approximately 100 sheets of 20 lb bond 
(80 g/m
2) paper). Doing so may cause a paper jam.
5.Adjust the document guides so they match the width of the document.
Note
Before starting a scan, make sure that the document is loaded in the scanner 
correctly. Scanning a curled document or a creased document can damage the 
document.
6.Start scanning from the...

30Using the Scanner
How to Feed with the Bypass Mode
1.
Move the feed selection lever on the lower left side of the front of the scanner 
down ( ).
Note
• Lowering the feed selection lever causes the document stoppers to go down.
• The ISIS/TWAIN driver settings change to the manual feed mode 
automatically when the feed selection lever is lowered. (See “Feeding 
Option,” on p. 83.)
2.Place the document into the document feed tray one sheet at a time and adjust 
the position of the document guides....

Using the Scanner31
Chapter 2
4.One sheet of the document is pushed against the document feed slot. The 
document is fed.
IMPORTANT
• When scanning documents that are fastened together, such as invoices, set 
the edge that is fastened together as the leading edge.
• Note that when scanning with nonseparated feed, if you place several 
documents that are not fastened together on the feed tray at one time, they 
will be fed together.
• In particular, very thin or curled documents will not be fed very well....

32Using the Scanner
4. Scanning Documents
When it scans with the DR-6030C, you need to install CapturePerfect 3.1, 
which is provided with the scanner, or ISIS/TWAIN-compatible application. 
This section describes the scanning flow of the CapturePerfect 3.1 application.
For details on how to install each application and the driver, see the Easy Start 
Guide.
IMPORTANT
If you scan a document under the condition that heavily consumes the memory 
of your PC, scanning may not be performed because of...

Using the Scanner33
Chapter 2
• “Select Job” SettingsScan mode settings (such as [Scan Batch to File], [Scan Batch to Printer], or 
[Scan Batch to Mail]) can be pre-registered, and then the settings can be 
selected for scanning by  selection from the tool bar in a simple 2-step 
sequence (
➀  Æ  ➁).
Note
The following two settings are pre-defined in the “Select Job” Settings. Up to 
99 settings can be registered.
• Color Document
Scan the document using 24-bit color, simplex, at 300 dpi resolution, and...

34Using the Scanner
CapturePerfect 3.1 Operation Procedure
This section describes how to start up CapturePerfect 3.1, select the scanner, 
and the procedure up to scanning with Scan Batch to File.
For details, see the CapturePerfect 3.1 Operation Guide and CapturePerfect 
Help.
1.Click the Windows [Start] button, and then click [All Programs] Æ 
[CapturePerfect 3.1] Æ [CapturePerfect 3.1].
CapturePerfect 3.1 
Operation Guide