Canon scanner imageFORMULA DR6030C User Manual

Before Using the Scanner15
Chapter 1
4. Installation Requirements
To use the DR-6030C, your computer must satisfy the following system 
requirements.
• One of the following operating systems:
- Microsoft Windows XP Professional SP3 or later
- Microsoft Windows XP Home Edition SP3 or later
- Microsoft Windows XP Professional x64 Edition SP2 or later
- Microsoft Windows Vista Home Basic SP2 or later
- Microsoft Windows Vista Home Premium SP2 or later
- Microsoft Windows Vista Business SP2 or later
-...

16Before Using the Scanner
- Not all USB interfaces provided as standard with personal computers are 
guaranteed. Contact your local authorized Canon dealer for more detailed 
information. 
- Scanning speeds are lower if your computer’s standard USB interface is 
USB Full-Speed (equal to USB 1.1). 
- The USB cable you are using should be the one originally bundled with 
the scanner or a Hi-Speed USB 2.0 compatible cable.
• Note the following points when using a SCSI card. 
- Be sure to use the procedure...

Before Using the Scanner17
Chapter 1
5. About the Setup Disc
The Canon DR-6030C scanner setup disc contains the software listed below:
• DR-6030C Driver
Scanner driver for use with the DR-6030C scanner.
• CapturePerfect 3.1
ISIS-compatible application developed for Canon document scanners.
Note
The following shows how the DR-6030C setup disc is configured. 
For instructions on how to install the software included on the setup disc, see 
the Easy Start Guide.
Menu screen Typical Installation
Read the...

18Before Using the Scanner 

Chapter 2
Using the Scanner
1. Documents .......................................... 20
2. Preparing the Trays ............................ 22
Setting Up the Document Feed Tray ......... 22
Document Eject Tray ................................. 23
Installing the Document Eject Guide ......... 25
3. Placing Documents ............................ 27
How to Feed with the Page Separation 
Mode ......................................................... 27
How to Feed with the Bypass Mode .......... 30
4....

20Using the Scanner
1. Documents
This scanner can scan documents ranging in size from business cards and 
checks to A3 size documents. It can also scan business cards.
The size of documents that this scanner can scan is shown below.
(*1) For information about the output directions, see “Document Eject Tray,” 
on p. 23.
(*2) You can scan documents that are a maximum of 118.1 inches (3000 mm) 
long by setting the scanner in the Long document mode. (See “Long 
Document Mode,” on p. 53.)
(*3) For information...

Using the Scanner21
Chapter 2
• Scanning documents that are written in pencil or similar material can make 
the rollers dirty, which can then transfer the dirt to subsequent documents. 
Always clean the rollers after scanning a document written in pencil.
• When scanning a two-sided document that is printed on thin paper, the image 
on the opposite side of each page may show through. Adjust the scanning 
intensity in the application software before scanning the document.
• Scanning the following types of...

22Using the Scanner
2. Preparing the Trays
Prepare the document feed tray and document eject tray according to the paper 
size and feed/eject method.
Setting Up the Document Feed Tray
1.
Hold the middle of the document feed tray and slowly open it toward you.
CAUTION
Do not place anything other than documents on the Document 
feed tray. Doing so may damage the scanner, reduce scanning 
quality, or cause the feed tray to fall off and injure someone.
2.Pull out the document feed tray extension when...

Using the Scanner23
Chapter 2
Document Eject Tray
The scanner has two eject methods; documents can be ejected to the front of 
the scanner in a U-turn path, or to the back of the scanner in a straight path. 
This is done according to whether document eject tray 2 is opened or closed. 
Select the eject method according to what you need to do.
Note
• The U-turn path is used to scan documents on paper of normal thickness. 
Scanned documents are ejected to the document eject tray.
• The straight path is used...

24Using the Scanner
2.Pull the document eject tray extension towards you to open it.
IMPORTANT
Make sure the document eject tray extension is open when using the scanner. If 
the document eject tray extension is not opened, ejected documents can fall 
from the tray and become jammed in the scanner.
Using the Straight Path
1.Open document eject tray 2.
Note
When using the straight path, the ejected documents are stacked in reverse 
order to how they were fed.
IMPORTANT
• Be sure there is enough space for...