Home > Canon > Printer > Canon printer PIXMA MG2920 User Manual

Canon printer PIXMA MG2920 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Canon printer PIXMA MG2920 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 735
    							Default Values Set at Factory (Network)Default Values of the LAN ConnectionItemThe defaultEnable/disable LANEnableSSIDBJNPSETUPCommunication modeInfrastructureWireless LAN securityDisableIPv4 IP addressAuto setupIPv6 IP addressAuto setupSet printer name*XXXXXXXXXXXXEnable/disable IPv6EnableEnable/disable WSD (WSD settings)EnableTimeout setting (WSD settings)1 minuteEnable/disable Bonjour (Bonjour settings)EnableService name (Bonjour settings)Canon MG2900 seriesLPR protocol settingEnablePictBridge communicationEnableWireless LAN DRXEnable
    (* The default value in this item varies by the machine.)
    Default Values of the Access Point Mode
    ItemThe defaultSSID (access point name)XXXXXX-MG2900seriesSecurity settingWPA2-PSK (AES)PasswordSerial number of the machine
    (XXXXXX is the last six digits of MAC address of the machine.)
    181 
    						
    							Connecting the Machine to the Computer Using a USB CableConnect the machine and the computer using a USB cable as the illustration below. The USB port is located
    on the rear of the machine.182 
    						
    							When Detecting the Printers Have the Same Name during SetupWhen the printer is detected during setup, you may see multiple printers of the same name on the detection
    result screen.
    Select a printer with checking the MAC address or the serial number set to the printer against that on the detection result screen.
    Note
    •
    A serial number may not be displayed on the detection result screen.
    To check the MAC address of the printer, print out the network setting information.
    Printing Out Network Setting Information
    183 
    						
    							Connecting to Other Computer with LAN/Changing the Connection
    Method from USB to LAN
    To add the computer connecting the machine with LAN or to change the connection method between the
    machine and the computer from USB to LAN, perform setup with the Setup CD-ROM or perform it according
    to the instructions on our website.
    Connecting to Other Computer with LANTo add the computer connecting the machine with LAN, perform setup with the Setup CD-ROM orperform it according to the instructions on our website.
    Changing the Connection Method from USB to LAN To change the connection method to LAN while you are using the machine with USB connection, perform
    setup again with the Setup CD-ROM or perform it again according to the instructions on our website and
    select  Change Connection Method .184 
    						
    							Printing Out Network Setting InformationYou can print out the current network settings of the machine.
    Important
    •
    This print out contains valuable information about your computer. Handle it with care.
    1.
    Make sure that the printer is turned on.
    2.
    Load a sheet of A4 or Letter-sized plain paper.
    3.
    Press and hold the  Stop button until the  Alarm lamp flashes 15 times.
    4.
    Release the  Stop button.
    The machine starts printing the network setting information.
    The following information on the machine's network setting is printed out.
    ItemExplanations of the itemSettingWireless LANWireless LANEnable/DisableConnectionConnection statusActive/InactiveMAC AddressMAC AddressXX:XX:XX:XX:XX:XXSSIDSSIDSSID of the wireless LAN/SSID of the access
    point modePasswordPasswordPassword of the access point mode (8 to 10
    alphanumeric characters)Communication ModeCommunication ModeInfrastructure/Access Point ModeChannel *1ChannelXX (1 to 13)EncryptionMethod of the Encryptionnone/WEP/TKIP/AESWEP Key LengthWEP Key LengthInactive/128/64AuthenticationMethod of the Authenticationnone/auto/open/shared/WPA-PSK/WPA2-PSKSignal StrengthSignal Strength0 to 100 [%]TCP/IP VersionTCP/IP VersionIPv4 & IPv6/IPv4IPv4 IP AddressSelected IP Address (IPv4)XXX.XXX.XXX.XXXIPv4 Default GatewayDefault Gateway (IPv4)XXX.XXX.XXX.XXXSubnet MaskSubnet MaskXXX.XXX.XXX.XXXIPv6 IP Address *2Selected IP Address (IPv6)XXXX:XXXX:XXXX:XXXX
    XXXX:XXXX:XXXX:XXXX
    185 
    						
    							IPv6 Default Gateway *2Default Gateway (IPv6)XXXX:XXXX:XXXX:XXXX
    XXXX:XXXX:XXXX:XXXXSubnet Prefix Length *2Subnet Prefix LengthXXXIPsec *3IPsec settingActiveSecurity Protocol *3Method of the Security ProtocolESP/ESP & AH/AHWPS PIN CODEWPS PIN codeXXXXXXXXWireless LAN DRXDiscontinuous reception
    (wireless LAN)Enable/DisableOther SettingsOther settings-Printer NamePrinter namePrinter name (Up to 15 alphanumeric characters)WSDWSD settingEnable/DisableWSD TimeoutTimeout1/5/10/15/20 [min]LPR ProtocolLPR protocol settingEnable/DisableBonjourBonjour settingEnable/DisableBonjour Service NameBonjour service nameBonjour service name (Up to 52 alphanumeric
    characters)PictBridge Commun.PictBridge CommunicationEnable/DisableDNS ServerGetting DNS Server
    automaticallyAuto/ManualPrimary ServerPrimary server addressXXX.XXX.XXX.XXXSecondary ServerSecondary server addressXXX.XXX.XXX.XXXProxy ServerProxy Server settingEnable/DisableProxy PortSpecifying Proxy Port1 to 65535Proxy AddressProxy AddressXXXXXXXXXXXXXXXXXXXX
    ("XX" represents alphanumeric characters.)
    *1 Depending on the country or region of purchase, one of the channels from 1 to 11 is printed.
    *2 Only when IPv6 is enabled, the status of the network is printed.
    *3 Only IPv6 and the IPsec setting are enabled, the status of the network is printed.
    186 
    						
    							About Network Communication
    Changing and Confirming Network Settings
    Screens for Network Connection of IJ Network Tool
    Other Screens of IJ Network Tool
    Appendix for Network Communication
    187 
    						
    							Changing and Confirming Network Settings
    IJ Network Tool
    Changing the Settings in the Wireless LAN Sheet
    Changing the WEP Detailed Settings
    Changing the WPA/WPA2 Detailed Settings
    Changing the Settings in the Wired LAN Sheet
    Changing the Settings in the Admin Password Sheet
    Monitoring Wireless Network Status
    Initializing the Network Settings of the Machine
    Viewing the Modified Settings
    188 
    						
    							IJ Network ToolIJ Network Tool is a utility that enables you to display and modify the machine network settings. It is installed
    when the machine is set up.
    Important
    •
    To use the machine over LAN, make sure you have the equipment necessary for the connection type, such as an access point or a LAN cable.
    •
    Do not start up IJ Network Tool while printing.
    •
    Do not print when IJ Network Tool is running.
    •
    If the firewall function of your security software is turned on, a message may appear warning thatCanon software is attempting to access the network. If the warning message appears, set the security
    software to always allow access.
    •
    IJ Network Tool has been verified to work on Windows XP, however, it does not support Fast User Switching. It is recommended to exit IJ Network Tool when switching users.
    Starting up IJ Network Tool
    1.
    Start up IJ Network Tool as shown below.
    •
    In Windows 8.1 or Windows 8, select  IJ Network Tool on the Start screen to start IJ Network
    Tool. If  IJ Network Tool  is not displayed on the  Start screen, select the  Search charm, then
    search for "IJ Network Tool".
    •
    In Windows 7, Windows Vista, or Windows XP, click  Start and select  All programs , Canon
    Utilities , IJ Network Tool , and then IJ Network Tool .
    Depending on the printer you are using, an administrator password is already specified for the printer at
    the time of purchase. When you change the network settings, authentication by the administrator
    password is required.
    For details:
    About the Administrator Password
    For improving security, it is recommended to change the administrator password.
    Changing the Settings in the Admin Password Sheet
    189 
    						
    							Changing the Settings in the Wireless LAN SheetTo change the wireless network settings of the printer, connect the printer and the computer with a USB
    cable temporarily. If you modify the wireless network settings of the computer over wireless connection
    without USB connection, your computer may not be able to communicate with the machine after modifying
    the settings.
    Note
    •
    This screen is not available depending on the printer you are using.
    •
    Activate the wireless LAN setting of the printer to change the settings in the  Wireless LAN sheet.
    1.
    Start up IJ Network Tool.
    2.
    Select the printer in  Printers:.
    When the printer is connected to the computer with a USB cable temporarily, select the printer with "USBnnn" (where "n" is a number) appearing in the  Port Name column.
    3.
    Select Configuration...  from the Settings menu.
    4.
    Click the  Wireless LAN  tab.
    The  Wireless LAN  sheet is displayed.
    For details on the  Wireless LAN sheet, see Wireless LAN Sheet .
    5.
    Change the settings or confirm.
    SSID: Enter the same value that was set for the target access point.
    When the printer is connected with USB, the  Search screen appears by clicking  Search.... Set the
    SSID of the access point by selecting the one of the detected access points.
    Search Screen
    190 
    						
    All Canon manuals Comments (0)

    Related Manuals for Canon printer PIXMA MG2920 User Manual