Canon Pixma Ip110 User Guide

							1.
Roll up the paper in the opposite direction to the paper curl as shown below.
2.
Check that the paper is now flat.
We recommend printing curl-corrected paper one sheet at a time.
Note
•
Depending on the media type, the paper may be smudged or may not be fed properly even if it is not curled inward. In such cases, follow the procedure described below to curl the paper outward within 0.1
inch / 3 mm (B) in height before printing. This may improve the print result.
(C) Printing side
We recommend printing paper that has been curled outward one sheet at a time.
Check4  Is the paper thickness lever set properly?
Adjust the position of the paper thickness lever properly according to the type of paper you are printing on.
For details on how to load paper or the position of the paper thickness lever:
Loading Paper
Depending on the printing content, the printing surface may become scratched or the corners or edges of the paper may become smudged even for the types of paper to set the lever to the right. In this case, set the paper thickness lever to the left.
451
 
						

							Reset the paper thickness lever to the right when you finish printing. If the paper thickness lever is not set back
to the right, the inside of the printer is more likely to get dirty due to the wider clearance between the print head
and the loaded paper. It may also reduce print quality.
Check5  If the intensity is set high, reduce the intensity setting and try printing again.
If you are using plain paper to print images with high intensity, the paper may absorb too much ink and become
wavy, causing paper abrasion.
Reduce the intensity setting in the printer driver and try printing again.
1.
Open the printer driver setup window.
How to Open the Printer Driver Setup Window
2.
On the  Main sheet, select  Manual for Color/Intensity , and then click Set....
3.
Drag the  Intensity slide bar on the  Color Adjustment  sheet to adjust the intensity.
Check6
 Is printing performed beyond the recommended printing area?
If you are printing beyond the recommended printing area of your printing paper, the lower edge of the paper
may become stained with ink.
Resize your original document in your application software.
Printing Area
Check7  Is the paper feed roller dirty?
Clean the paper feed roller.
Cleaning the Paper Feed Roller
Note
•
Cleaning the paper feed roller will wear the roller, so perform this procedure only when necessary.
Check8  Is the inside of the printer dirty?
When performing duplex printing, the inside of the printer may become stained with ink, causing the printout to
become smudged.
Perform the Bottom Plate Cleaning to clean the inside of the printer.
Cleaning the Inside of the Printer (Bottom Plate Cleaning)
Note
•
To prevent the inside of the printer from stains, set the paper size correctly.
Check9  Set the time to dry the printed surface longer.
Doing so gives the printed surface enough time to dry so that paper smudged and scratched are prevented.
1.
Make sure that the printer is turned on.
2.
Open the printer driver setup window.
How to Open the Printer Driver Setup Window
3.
Click the  Maintenance  tab and then  Custom Settings .
4.
Drag the Ink Drying Wait Time  slide bar to set the wait time, and then click  OK.
5.
Confirm the message and click  OK.
452
 
						

							Back of the Paper Is Smudged
Check1 Did you confirm the paper and print quality settings?
Print Results Not Satisfactory
Check2  Perform the Bottom Plate Cleaning to clean the inside of the printer.
Cleaning the Inside of the Printer (Bottom Plate Cleaning)
Note
•
When performing borderless printing, duplex printing, or too much printing, the inside may become stained
with ink.
453
 
						

							Colors Are Uneven or Streaked
 Colors Are Uneven
 Colors Are Streaked
Check1 Did you confirm the paper and print quality settings?
Print Results Not Satisfactory
Check2 Print the Nozzle Check Pattern and perform any necessary maintenance
operations such as Print Head Cleaning.
Print the Nozzle Check Pattern to determine whether the ink ejects properly from the print head nozzles.Refer to 
When Printing Becomes Faint or Colors Are Incorrect  for the Nozzle Check Pattern printing, Print Head
Cleaning, and Print Head Deep Cleaning.
•
If the Nozzle Check Pattern is not printed correctly:
Check to see if a particular color's ink tank is not empty.
If the Nozzle Check Pattern is not printed correctly though ink is sufficient, perform the Print Head Cleaning and try printing the Nozzle Check Pattern again.
•
If the problem is not resolved after performing the Print Head Cleaning twice:
Perform the Print Head Deep Cleaning.
If the problem is not resolved after performing the Print Head Deep Cleaning, turn off the printer and
perform another Print Head Deep Cleaning after 24 hours.
•
If the problem is not resolved after performing the Print Head Deep Cleaning twice:
454
 
						

							If Print Head Deep Cleaning does not resolve the problem, the print head may be damaged. Contact the
service center.
Check3  Perform Print Head Alignment.
Aligning the Print Head
Note
•
If the problem is not resolved after performing the Print Head Alignment, perform Print Head Alignment
manually referring to 
Aligning the Print Head Position from Your Computer .
455
 
						

							Ink Is Not Ejected
Check1 Has the ink run out?
Open the print head cover, then check the status of ink lamp.
Checking the Ink Status
Check2  Are the print head nozzles clogged?
Print the Nozzle Check Pattern to determine whether the ink ejects properly from the print head nozzles. Refer to 
When Printing Becomes Faint or Colors Are Incorrect  for the Nozzle Check Pattern printing, Print Head
Cleaning, and Print Head Deep Cleaning.
•
If the Nozzle Check Pattern is not printed correctly:
Check to see if a particular color's ink tank is not empty.
If the Nozzle Check Pattern is not printed correctly though ink is sufficient, perform the Print Head Cleaning and try printing the Nozzle Check Pattern again.
•
If the problem is not resolved after performing the Print Head Cleaning twice:
Perform the Print Head Deep Cleaning.
If the problem is not resolved after performing the Print Head Deep Cleaning, turn off the printer and
perform another Print Head Deep Cleaning after 24 hours.
•
If the problem is not resolved after performing the Print Head Deep Cleaning twice:
If Print Head Deep Cleaning does not resolve the problem, the print head may be damaged. Contact the
service center.
456
 
						

							Problems with the Printer
The Printer Cannot Be Powered On
The Printer Turns Off Unintentionally
Cannot Connect to Computer with a USB Cable Properly
Cannot Communicate with the Printer with USB Connection
Print Head Holder Does Not Move to the Position for Replacing
Printer Status Monitor Is Not Displayed
457
 
						

							The Printer Cannot Be Powered On
Check1 Press the  ON button.
Check2
 Make sure that the power plug is securely plugged into the power cord
connector of the printer, then turn it back on.
Check3  Unplug the printer from the power supply, then plug the printer back in and turn
the printer back on after leaving it for at least 2 minutes.
Check4  If you use a battery, check the remaining level of the battery.
For details on how to check it, refer to the battery's instruction manual. If the battery is running out, replace the battery with a charged one, or connect the AC adapter to the printer.
If the problem is not resolved, contact the service center.
458
 
						

							The Printer Turns Off Unintentionally
Check Deactivate the setting to turn the unit off automatically.
The printer turns off automatically according to the elapsed time you specified if you activate the setting to turn
the unit off automatically.
If you do not want the printer to turn off automatically, open the printer driver setup window and in  Auto Power
under the  Maintenance  sheet, select  Disable for Using AC Adapter  in Auto Power Off .
459
 
						

							Cannot Connect to Computer with a USB Cable ProperlyPrinting Speed Is Slow/Hi-Speed USB Connection Does Not Work/"This
device can perform faster" Message Is Displayed
If your system environment is not fully compatible with Hi-Speed USB, the printer will operate at a lower
speed provided under USB 1.1. In this case, the printer operates properly but printing speed may slow
down due to communication speed.
Check  Check the following to make sure that your system environment supports Hi-
Speed USB connection.
•
Does the USB port on your computer support Hi-Speed USB connection?
•
Does the USB cable or the USB hub support Hi-Speed USB connection?
Be sure to use a certified Hi-Speed USB cable. We recommend that the cable is no longer than around
10 feet / 3 meters.
•
Does the operating system of your computer support Hi-Speed USB connection?
Obtain and install the latest update for your computer.
•
Does the Hi-Speed USB driver operate properly?
Obtain the latest version of the Hi-Speed USB driver compatible with your hardware and reinstall it on
your computer.
Important
•
For details on Hi-Speed USB of your system environment, contact the manufacturer of your computer,
USB cable, or USB hub.
460