Canon Pixma Ip110 User Guide

							Connecting the Printer to the Computer Using a USB CableConnect the printer and the computer using a USB cable as the illustration below. The USB port is located
on the side of the printer.181
 
						

							When Detecting the Printers Have the Same Name during SetupWhen the printer is detected during setup, you may see multiple printers of the same name on the detection
result screen.
Select a printer with checking the MAC address or the serial number set to the printer against that on the detection result screen.
Note
•
A serial number may not be displayed on the detection result screen.
To check the MAC address of the printer, print out the network setting information.
Printing Out Network Setting Information
182
 
						

							Connecting to Other Computer with LAN/Changing the Connection
Method from USB to LAN
To add the computer connecting the printer with LAN or to change the connection method between the
printer and the computer from USB to LAN, perform setup with the Setup CD-ROM or perform it according
to the instructions on our website.
Connecting to Other Computer with LANTo add the computer connecting the printer with LAN, perform setup with the Setup CD-ROM or perform it
according to the instructions on our website.
Changing the Connection Method from USB to LAN
To change the connection method to LAN while you are using the printer with USB connection, perform
setup again with the Setup CD-ROM or perform it again according to the instructions on our website and
select  Change Connection Method .183
 
						

							Printing Out Network Setting InformationYou can print out the current network settings of the printer.
Important
•
This print out contains valuable information about your computer. Handle it with care.
1.
Make sure that the printer is turned on.
2.
Load a sheet of A4 or Letter-sized plain paper.
3.
Press and hold the  RESUME/CANCEL  button, then release the button when the  POWER
lamp flashes 6 times.
The printer starts printing the network setting information.
The following information on the printer's network setting is printed out.
ItemExplanations of the itemSettingWireless LANWireless LANEnable/DisableConnectionConnection statusActive/InactiveMAC AddressMAC AddressXX:XX:XX:XX:XX:XXSSIDSSIDSSID of the wireless LAN/SSID of the access
point modePasswordPasswordPassword of the access point mode (8 to 10
alphanumeric characters)Communication ModeCommunication ModeInfrastructure/Access Point ModeChannel *1ChannelXX (1 to 13)EncryptionMethod of the Encryptionnone/WEP/TKIP/AESWEP Key LengthWEP Key LengthInactive/128/64AuthenticationMethod of the Authenticationnone/auto/open/shared/WPA-PSK/WPA2-PSKSignal StrengthSignal Strength0 to 100 [%]TCP/IP VersionTCP/IP VersionIPv4 & IPv6/IPv4IPv4 IP AddressSelected IP Address (IPv4)XXX.XXX.XXX.XXXIPv4 Default GatewayDefault Gateway (IPv4)XXX.XXX.XXX.XXXSubnet MaskSubnet MaskXXX.XXX.XXX.XXXIPv6 IP Address *2Selected IP Address (IPv6)XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXXIPv6 Default Gateway *2Default Gateway (IPv6)XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXX
184
 
						

							Subnet Prefix Length *2Subnet Prefix LengthXXXIPsec *3IPsec settingActiveSecurity Protocol *3Method of the Security ProtocolESP/ESP & AH/AHWPS PIN CODEWPS PIN codeXXXXXXXXWireless LAN DRXDiscontinuous reception
(wireless LAN)Enable/DisableOther SettingsOther settings-Printer NamePrinter namePrinter name (Up to 15 alphanumeric characters)WSDWSD settingEnable/DisableWSD TimeoutTimeout1/5/10/15/20 [min]LPR ProtocolLPR protocol settingEnable/DisableBonjourBonjour settingEnable/DisableBonjour Service NameBonjour service nameBonjour service name (Up to 52 alphanumeric
characters)PictBridge Commun.PictBridge CommunicationEnable/DisableDNS ServerGetting DNS Server
automaticallyAuto/ManualPrimary ServerPrimary server addressXXX.XXX.XXX.XXXSecondary ServerSecondary server addressXXX.XXX.XXX.XXXProxy ServerProxy Server settingEnable/DisableProxy PortSpecifying Proxy Port1 to 65535Proxy AddressProxy AddressXXXXXXXXXXXXXXXXXXXX
("XX" represents alphanumeric characters.)
*1 Depending on the country or region of purchase, one of the channels from 1 to 11 is printed.
*2 Only when IPv6 is enabled, the status of the network is printed.
*3 Only when IPv6 and the IPsec setting are enabled, the status of the network is printed.
185
 
						

							About Network Communication
Changing and Confirming Network Settings
Screens for Network Connection of IJ Network Tool
Other Screens of IJ Network Tool
Appendix for Network Communication
186
 
						

							Changing and Confirming Network Settings
IJ Network Tool
Changing the Settings in the Wireless LAN Sheet
Changing the WEP Detailed Settings
Changing the WPA/WPA2 Detailed Settings
Changing the Settings in the Wired LAN Sheet
Changing the Settings in the Admin Password Sheet
Monitoring Wireless Network Status
Initializing the Network Settings of the Machine
Viewing the Modified Settings
187
 
						

							IJ Network ToolIJ Network Tool is a utility that enables you to display and modify the machine network settings. It is installed
when the machine is set up.
Important
•
To use the machine over LAN, make sure you have the equipment necessary for the connection type, such as an access point or a LAN cable.
•
Do not start up IJ Network Tool while printing.
•
Do not print when IJ Network Tool is running.
•
If the firewall function of your security software is turned on, a message may appear warning thatCanon software is attempting to access the network. If the warning message appears, set the security
software to always allow access.
•
IJ Network Tool has been verified to work on Windows XP, however, it does not support Fast User Switching. It is recommended to exit IJ Network Tool when switching users.
Starting up IJ Network Tool
1.
Start up IJ Network Tool as shown below.
•
In Windows 8.1 or Windows 8, select  IJ Network Tool on the Start screen to start IJ Network
Tool. If  IJ Network Tool  is not displayed on the  Start screen, select the  Search charm, then
search for "IJ Network Tool".
•
In Windows 7, Windows Vista, or Windows XP, click  Start and select  All programs , Canon
Utilities , IJ Network Tool , and then IJ Network Tool .
Depending on the printer you are using, an administrator password is already specified for the printer at
the time of purchase. When you change the network settings, authentication by the administrator
password is required.
For details:
About the Administrator Password
For improving security, it is recommended to change the administrator password.
Changing the Settings in the Admin Password Sheet
188
 
						

							Changing the Settings in the Wireless LAN SheetTo change the wireless network settings of the printer, connect the printer and the computer with a USB
cable temporarily. If you modify the wireless network settings of the computer over wireless connection
without USB connection, your computer may not be able to communicate with the machine after modifying
the settings.
Note
•
This screen is not available depending on the printer you are using.
•
Activate the wireless LAN setting of the printer to change the settings in the  Wireless LAN sheet.
1.
Start up IJ Network Tool.
2.
Select the printer in  Printers:.
When the printer is connected to the computer with a USB cable temporarily, select the printer with "USBnnn" (where "n" is a number) appearing in the  Port Name column.
3.
Select Configuration...  from the Settings menu.
4.
Click the  Wireless LAN  tab.
The  Wireless LAN  sheet is displayed.
For details on the  Wireless LAN sheet, see Wireless LAN Sheet .
5.
Change the settings or confirm.
SSID: Enter the same value that was set for the target access point.
When the printer is connected with USB, the  Search screen appears by clicking  Search.... Set the
SSID of the access point by selecting the one of the detected access points.
Search Screen
189
 
						

							Note•
Enter the same SSID that the access point is configured to use. The SSID is case-sensitive.
Encryption Method: Select the encryption method used over the wireless LAN.
You can change WEP settings with selecting  Use WEP and clicking  Configuration... .
Changing the WEP Detailed Settings
You can change WPA/WPA2 settings with selecting  Use WPA/WPA2 and clicking Configuration... .
Changing the WPA/WPA2 Detailed Settings
Important
•
If all encryption types of the access point, printer, or computer do not match, the printer cannot
communicate with the computer. If the printer cannot communicate with the computer after the encryption type of the printer was switched, make sure that encryption types for the computer andthe access point match that set to the printer.
•
If you connect to a network that is not protected with security measures, there is a risk of disclosing
data such as your personal information to a third party.
TCP/IP Setup: Sets the IP address of the printer to be used over the LAN. Specify a value appropriate for your
network environment.
6.
Click  OK.
After changing configuration, a screen is displayed asking you for confirmation before the settings are
sent to the printer. If you click  Yes, the settings are sent to the printer and the  Transmitted Settings
screen is displayed.
Note
•
Changing the network settings with the USB cable temporarily may switch the default printer. In
this case, reset  Set as Default Printer .
190