Canon Imagerunner 2318 User Guide

Canceling a Job2-23
Basic Operations
2
NOTE
•The current job is listed first on the Status screen.
•The LCD display can display characters in ASCII code. Using other character codes may 
cause characters garbled on the LCD display.
•The messages displayed on the Status screen are as follows:
-  = Current job
-  = Current job that has been temporarily stopped by pressing   (Stop).
-  = Reserved jobs
3Use [ ] or [ ] to select  
➞ press [OK].
The Status screen appears.
4Use [ ] or [ ] to select the job 
you...

Canceling a Job2-24
Basic Operations
2
NOTE
•You cannot select multiple jobs and cancel them all at once. Select and cancel one job at 
a time.
•The LCD display can display characters in ASCII code. Using other character codes may 
cause characters garbled on the LCD display.
7Press  (Reset) to return to the Standby display.
6Use [ ] or [ ] to select  ➞ 
press [OK].
If you do not want to cancel the job, select 
 to return to the previous display.
The selected job is canceled.
Repeat steps 4 and 6 to...

CHAPTER
3-1
3Routine Maintenance
This chapter describes how to load paper, perform routine cleaning operations, and replace 
consumables, such as toner and staple cartridges.
Paper Drawers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Loading Paper  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Adjusting a Paper Drawer to Hold a Different Paper Size...

Paper Drawers3-2
Routine Maintenance
3
Paper Drawers
This section describes how to load paper into the paper drawers.
NOTE
•The following paper sizes can be loaded in Paper Drawers 1, 2, 3, and 4:
- A4, A4R, A3, or A5
•Paper Drawer 2 can be added by attaching the optional Cassette Feeding Module-J1 
or -K1.
•Paper Drawer 3 (and 4) can be added by attaching the optional Cassette Feeding 
Module-K1.
•For more information on available paper stock which can be loaded in the paper drawers, 
see “Available...

Paper Drawers3-3
Routine Maintenance
3
- Paper on which color images have been copied (Do not copy on the reverse side of this 
paper either.)
- Paper which has been printed on using a thermal transfer printer (Do not print on the 
reverse side of this paper either.)
•Fan the stack of paper well before loading it, and align the edges of the paper stack on a 
flat surface.
•Never place paper or any other items in the empty part of the drawer next to the paper 
stack. Doing so may cause paper jams.
NOTE...

Paper Drawers3-4
Routine Maintenance
3
3Open a package of paper, and 
take out the paper stack from the 
package.
CAUTION
When loading paper, take care not to 
cut your hands on the edges of the 
paper.
IMPORTANT
Rewrap any remaining paper in its 
original package, and store it in a dry 
place, away from direct sunlight.
NOTE
• For high-quality printouts, use paper 
recommended by Canon.
• Before loading paper, always fan the 
sheets several times, and align the 
edges to facilitate feeding.
4Load the...

Paper Drawers3-5
Routine Maintenance
3
IMPORTANT
•Rolled or curled paper must be straightened out prior to use.
•Make sure that the height of the paper stack does not exceed the loading limit mark ( ) 
at the back of the paper drawer and the corners are below the paper size guide clips.
•Make sure that the paper-size detecting lever is set correctly. If the lever is set on a 
wrong position, paper jams or dirty prints may occur, or the inside of the machine may 
get dirty.
NOTE
•Each paper drawer holds...

Paper Drawers3-6
Routine Maintenance
3
Adjusting a Paper Drawer to Hold a Different Paper Size
If you want to change the size of paper in a paper drawer, follow the procedure 
described below to adjust the paper drawer guides.
NOTE
Please contact your Canon service representative about the settings for U1, U2, and U3 paper.
1Pull out the paper drawer, and 
remove all the loaded paper.
2Push down the metal plate to lock it.
3Detach the end guide and reattach 
it to the slots aligned with the mark...

Paper Drawers3-7
Routine Maintenance
3
NOTE
Attach the end guide while pressing down the point indicated with ‘A’.
4Lift up the lock lever on the front slide guide, and slide it 
backwards or forwards to align it with the groove marked with the 
desired paper size.
5Lower the lock lever to lock the 
front slide guide into place.
IMPORTANT
Be sure to set the lock lever correctly. If 
the lock lever is positioned incorrectly for 
the type of paper loaded in the paper 
drawer, the wrong paper type will be...

Paper Drawers3-8
Routine Maintenance
3
7Move the paper size detecting lever on the left side of the paper 
drawer, so that the arrow points to the paper size being loaded.
IMPORTANT
Make sure that the paper size detecting lever is set correctly. If the lever is positioned 
incorrectly to the size of paper loaded in the paper drawer, the wrong paper size will be 
shown on the LCD display. This may also cause paper jams, dirty prints, or make the 
inside of the machine dirty.
NOTE
 displayed on the LCD...