Canon Imageprograf Ipf8300 User Guide
Have a look at the manual Canon Imageprograf Ipf8300 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
•If no print job was received 1.Press the Load button. 2.Press ▲ or ▼ to select Cut Sheet , and then press the OK button. Note•If any paper has been advanced that will not be used, a message is shown requesting you to remove it. Press ▲ or ▼ to select " Yes", and then press the OK button. Remove the paper and go to the next step. 2. Lift the Release Lever and open the Top Cover. Handling Paper > Handling sheets >iPF8300Loading Sheets in the Printer7803
Important•Do not touch the Linear Scale (a), Carriage Shaft (b), or Fixed Blade (c). 3. With a sheet lengthwise and printing-side up, insert it between the Platen (a) and the Paper Retainer (b). Align the edges of the sheet as follows. 1. Align the sheet with the Paper Alignment Line (c) at right. 2. Align the inserted edge of the sheet with the leading edge of the Paper Alignment Line (d), as shown. Handling Paper > Handling sheets >Loading Sheets in the PrinteriPF83007804
When inserted, sheets are automatically held by suction against the Platen. Important•Load a sheet so that it is parallel to the Paper Alignment Line at right (c). Loading paper askew will cause an error. • Warped paper may rub against the Printhead. Straighten paper if it is warped before loading it.Note•You can adjust the strength of suction holding paper against the Platen when the Release Lever is up. If it is difficult to load paper, press the ▲ or ▼ button on the Control Panel to adjust the strength. Set suction stronger by pressing the ▲ button or weaker with the ▼ button. Three settings are available. However, even if you increase the suction, it may not be sufficient to hold some types of paper against the Platen well. In this case, use your hand to load the paper. • Sheets are held in place by suction through holes on the Platen. Although the suction may produce a noise when paper is loaded in some positions, it does not indicate a problem. If the noise is distract- ing, try moving the paper over slightly to the left or right (up to 1 mm [0.039 in]) while keeping it parallel to the Paper Alignment Line. • The suction remains on for about 30 seconds during loading. If you cannot finish loading a sheet dur- ing this time, pull the sheet away and reinsert it to start the suction again. Handling Paper > Handling sheets >iPF8300Loading Sheets in the Printer7805
4.Lower the Release Lever and close the Top Cover. • If a print job was received Pressing the OK button will advance the paper, and then printing will begin. • If no print job was received A menu for selection of the type of paper is automatically shown on the Display Screen. Press ▲ or ▼ to select the type of paper, and then press the OK button. The printer now starts feeding the paper. Note• For details on types of paper to select, see the Paper Reference Guide. (See "Types of Paper .") →P.768 • When using the Output Stacker, if you will print on large, stiff sheets, we recommend adjusting the Output Stacker into the lowest position to prevent printed sheets from being bent. (See "Using the Output Stacker .") →P.813 Printing From a Desired Starting Point Print on sheets from a desired starting point as follows. Set Width Detection to Off 1. On the Tab Selection screen of the Control Panel, press ◀ or ▶ to select the Paper tab ( ). Handling Paper > Handling sheets >Printing From a Desired Starting PointiPF83007806
Note•If the Tab Selection screen is not displayed, press the Menu button. 2.Press the OK button. The Paper Menu is displayed. 3. Press ▲ or ▼ to select Paper Details , and then press the OK button. 4. Press ▲ or ▼ to select the type of paper, and then press the OK button. 5. Press ▲ or ▼ to select Width Detection , and then press the OK button. 6. Press ▲ or ▼ to select Off, and then press the OK button. Load paper in the desired position to start printing from Follow these instructions to load paper at the desired starting position for printing when Width Detection is Off . 1. If you did not send a print job in advance, a menu for selection of the type of paper is displayed. Press ▲ or ▼ to select the type of paper, and then press the OK button. Note•If a print job was received before paper was advanced, the media type and size specified by the job are shown on the Display Screen. Thus, this screen is not displayed. Go to step 2. 2. "Width Detection OFF. OK to continue? " is now shown on the Display Screen. Press ▲ or ▼ to select " Leave OFF ", and then press the OK button. 3. After a menu for selection of the paper size is displayed, press ▲ or ▼ to select the paper size, and then press the OK button. 4. Open the Top Cover and check the position where paper is loaded. Handling Paper > Handling sheets >iPF8300Printing From a Desired Starting Point7807
To start printing from the current position, close the Top Cover. To reposition the paper, lift the Release Lever.Handling Paper > Handling sheets >Printing From a Desired Starting PointiPF83007808
5.Keeping the right edge of the paper aligned with the extended line of the paper alignment line (a) on the right side of the printer and the position from which to start printing aligned with the groove (b) at the far end of the platen, load the paper.Handling Paper > Handling sheets >iPF8300Printing From a Desired Starting Point7809
6.Lower the Release Lever and close the Top Cover. Removing Sheets Remove sheets from the printer as follows. 1. On the Tab Selection screen of the Control Panel, press ◀ or ▶ to select the Paper tab ( ). Note•If the Tab Selection screen is not displayed, press the Menu button. 2.Press the OK button. The Paper Menu is displayed. 3. Press ▲ or ▼ to select Eject Paper , and then press the OK button. 4. Press ▲ or ▼ to select " Yes", and then press the OK button. The paper is ejected from the front of the printer. Handling Paper > Handling sheets >Removing SheetsiPF83007810
5.Open the Top Cover, lift the Release Lever, and remove the sheet. 6.Lower the Release Lever and close the Top Cover. Handling Paper > Handling sheets >iPF8300Removing Sheets7811
Output Stacker Output Stacker ............................................................................................................................................... 812 Using the Output Stacker ................................................................................................................................ 813 Storing the Output Stacker .............................................................................................................................. 819 Output Stacker a. Output Stacker A cloth tray that catches ejected documents. b. White tag A point of reference for attaching the Output Stacker in the right direction. Handling Paper > Output Stacker >Output StackeriPF83007812