Canon Eos Rebel T3 1100d Instruction Manual

							101
Set exposure compensation if the exposure (without flash) does not come out 
as desired. This feature can be used in Crea tive Zone modes (except ). You can set the exposure compensation up to ±5 stops in 1/3-stop increments.
Making it brighter:
Hold down the < O> button and 
turn the < 6> dial to the right. 
(Increased exposure)
Making it darker: Hold down the < O> button and 
turn the < 6> dial to the left. 
(Decreased exposure)
XAs shown in the figure, the exposure 
level is displayed on the LCD monitor 
and in the viewfinder.
  After taking the picture, cancel the 
exposure compensation by setting 
it back to 0.
Setting Exposure Compensation N
O Setting Exposure Compensation
Increased exposure for a brighter image
Decreased exposure for a darker image
Dark exposure Increased expo sure for a brighter image
 The exposure compensation  amount displayed in the viewfinder goes up 
to only ±2 stops. If the exposure  compensation amount exceeds ±2 
stops, the end of t he exposure level indicator will display < I> or < J>.
  The exposure compensation  can also be set with [2 Expo. comp./
AEB ] (p.103). If you will set exposure  compensation exceeding ±2 stops, 
you should use [2  Expo. comp./AEB] to set it.
COPY  
						

							Setting Exposure CompensationN
102
Set flash exposure compensation if  the flash exposure of the subject 
does not come out as desired. You can set the flash exposure 
compensation up to ±2 stops in 1/3-stop increments.
1Press the < Q> button. (7 )
XThe Quick Control screen will appear 
(p.40).
2Select [ y].
 Press the < S> key to select [ y*].X[Flash exposure comp.] will be 
displayed at the bottom.
3Set the flash exposure 
compensation amount.
 To make the flash exposure brighter, 
turn the < 6> dial to the right. 
(Increased exposure)
To make it darker, turn the < 6> dial 
to the left. (Decreased exposure)
XWhen you press the shutter button 
halfway, the < y> icon will appear in 
the viewfinder.
  After taking the picture, cancel the 
flash exposure compensation by 
setting it back to 0.
y  Flash Exposure Compensation
If [2  Auto Lighting Optimizer ] (p.107) is set to any setting other than 
[ Disable ], the image may look bright even if a decreased exposure 
compensation or decreased flash exposure compensation has been set.
You can also set flash expo sure compensation with [Built-in flash func. 
setting ] in [1 Flash control ] (p.167).
COPY  
						

							103
This feature takes exposure compensation a step further by varying the 
exposure automatically (up to ±2 stops in 1/3-stop increments) with 
three shots as shown below. You can then choose the best exposure.
This is called AEB (Auto Exposure Bracketing).
1Select [Expo. comp./AEB].
  Under the [ 2] tab, select [Expo. 
comp./AEB ], then press < 0>.
2Set the AEB amount.
  Turn the < 6> dial to set the AEB 
amount.
  Press the < U> key to set the 
exposure compensation amount. If 
AEB is combined with exposure 
compensation, AEB will be applied 
centering on the exposure 
compensation amount.
  Press < 0> to set it.
  When you press the < M> button 
to exit the menu, the AEB level will be 
displayed on the LCD monitor.
3Take the picture.
  Focus and press the shutter button 
completely. The three bracketed 
shots will be taken in this sequence: 
Standard exposure, decreased 
exposure, and increased exposure.
3  Auto Exposure Bracketing N
Standard exposure Darker exposure
(Decreased exposure) Brighter exposure
(Increased exposure)
AEB amount
COPY  
						

							3 Auto Exposure BracketingN
104
 Follow steps 1 and 2 to turn off the AEB amount display.
  The AEB setting will also be cancel ed automatically if the power 
switch is set to < 2>, flash recycling is completed, etc.
  Using AEB with continuous shooting:
If  continuous shooting (p.86)  has been set and you press the 
shutter button completely, the three bracketed shots will be taken 
continuously in this sequence : Standard exposure, decreased 
exposure, and increased exposure.
  Using AEB with < u> single shooting:
Press the shutter button three time s to take the three bracketed 
shots. The three bracketed shots will be exposed in the following 
sequence: Standard exposure, decr eased exposure, and increased 
exposure.
  Using AEB with the self-timer:
If you use the self-timer < j> < l > (p.87), the three bracketed 
shots will be taken continuously after 10 sec. or 2 sec. With  
(p.87) set, the number of contin uous shots will be three times the 
number set.
Canceling AEB
Shooting Tips
  Neither flash nor bulb exposu res can be used with AEB.
  If [2  Auto Lighting Optimizer ] (p.107) is set to any setting other than 
[ Disable ], the AEB’s effect might be minimal.
COPY  
						

							105
You can lock the exposure when the area of focus is to be different from 
the exposure metering area or when you  want to take multiple shots at 
the same exposure setting. Press the  button to lock the exposure, 
then recompose and take the shot. This is called AE (autoexposure) 
lock. It is effective for backlit subjects.
1Focus the subject.
  Press the shutter button halfway.
XThe exposure setting will be 
displayed.
2Press the < A> button. (0 )
XThe < A> icon lights in the viewfinder 
to indicate that the exposure setting is 
locked (AE lock).
  Each time you press the  button, 
it locks the current autoexposure 
setting.
3Recompose and take the picture.
  If you want to maintain the AE lock 
while taking more shots, hold down 
the < A> button and press the shutter 
button to take another shot.
* When the lens’ fo cus mode switch is set to , AE lock is applied at  the center AF point.
A Locking the Exposure N
AE Lock Effects
Metering Mode 
(p.100)AF Point Selection Method  (p.83)
Automatic SelectionManual Selection
q*AE lock is applied at the AF 
point that achieved focus.AE lock is applied at the 
selected AF point.
weAE lock is applied at the center AF point.
COPY  
						

							106
If the subject is on the side of the frame and you use flash, the subjec\
t may 
turn out to be too bright or dark depending on the background, etc. This is 
when you should use FE lock. After se tting the proper flash exposure for 
the subject, you can recompose (put  the subject toward the side) and 
shoot. This feature can also be used  with a Canon EX-series Speedlite.
* FE stands for Flash Exposure.
1Press the  button.
XThe built-in flash will rise.
  Press the shutter button halfway and 
look in the viewfinder to check that 
the < D> icon is lit.
2Focus the subject.
3Press the < A> button. (8 )
 
Aim the viewfinder center over the 
subject where you want to lock the flash 
exposure, then press the <
A> button.XThe flash will fire a preflash and the 
required flash output is calculated 
and retained in memory.
XIn the viewfinder, “ FEL” is displayed 
for a moment and  will light.
 
Each time you press the  button, a 
preflash is fired and the required flash output 
is calculated and retained in memory.
4Take the picture.
  Compose the shot and press the 
shutter button completely.
XThe flash is fired when the picture is 
taken.
A Locking the Flash Exposure N
If the subject is too far away and beyond the effectiv e range of the flash, the 
 icon will blink. Get closer to the subject and rep eat steps 2 to 4.
COPY  
						

							107
If the image comes out dark or the contrast is low, the brightness and 
contrast can be corrected automatically. This feature is called Auto 
Lighting Optimizer. The default setting is [
Standard]. With JPEG images, 
the correction is done when the image is captured. For RAW images, it can 
be corrected with Digital Photo Prof essional (provided software, p.270).
1Select [Auto Lighting Optimizer].
 Under the [ 2] tab, select [Auto 
Lighting Optimizer ], then press 
< 0 >.
2Select the setting.
  Select the desired setting, then press 
.
3Take the picture.
  The image will be recorded with the 
brightness and contrast corrected if 
necessary.
3  Correcting the Brightness and Contrast AutomaticallyN
Without correction With correction
 Under [ 7 Custom Functions (C.Fn) ], if [5: Highlight tone priority ] is 
set to [ 1: Enable ], the Auto Lighting Optimizer  will be set automatically to 
[ Disable ] and you cannot change this setting.
  Depending on the shoo ting conditions, noise might increase.
  If a setting other than [ Disable] is set and you use exposure 
compensation, flash expo sure compensation, or manual exposure to 
darken the exposure, the  image might still come out bright. If you want a 
darker exposure, set [ Auto Lighting Optimizer ] to [Disable ] first.
In Basic Zone modes, [ Standard] is set automatically.
COPY  
						

							108
Due to the lens characteristics, the four corners of the picture might look 
darker. This phenomenon is  called lens light fall-off or drop in peripheral 
illumination and can be corrected automatically. The default setting is 
[Enable ]. With JPEG images, the correction is done when the image is 
captured. For RAW images, it can be corrected with Digital Photo 
Professional (provided software, p.270).
1Select [Peripheral illumin. 
correct.].
  Under the [ 1] tab, select 
[Peripheral illumin. correct.], then 
press < 0>.
2Select the setting.
  On the screen, check that 
[Correction data available ] is 
displayed for the attached lens.
  If [Correction data not available] is 
displayed, see “About the Lens 
Correction Data” on the next page.
  Select [Enable ], then press .
3Take the picture.
  The image will be recorded with the 
corrected peripheral illumination.
3  Correcting the Image’s Dark Corners
Correction disabled Correction enabled
COPY  
						

							109
3 Correcting the Image’s Dark Corners
The camera already contains lens  peripheral illumination correction 
data for about 25 lenses. In step 2, if you select [ Enable], the peripheral 
light correction will be applied automatically for any lens whose 
correction data has been registered in the camera.
With EOS Utility (provided softwa re, p.270), you can check which 
lenses have their correction data regi stered in the camera. You can also 
register the correction data for unregi stered lenses. For details, see the 
Software Instruction Manual (CD- ROM) for EOS Utility (p.272).
About the Lens Correction Data
 For JPEG images already captured , lens peripheral illumination 
correction cannot be applied.
  Depending on shooting conditions , noise might appear on the image 
periphery.
  When using a non-Canon lens, setting the correction to [ Disable] is 
recommended, even if [ Correction data available] is displayed.
 Lens peripheral light co rrection is also applied when an Extender is 
attached.
  If the correction data for the attached  lens has not been registered to the 
camera, the result will be  the same as when the correction is set to 
[ Disable ].
  The correction amount applied will be  slightly lower than the maximum 
correction amount settable with Di gital Photo Professional (provided 
software).
  If the lens does not have distance in formation, the correction amount will 
be lower.
  The higher the ISO speed, the lowe r the correction amount will be.
COPY  
						

							110
You can customize a Picture Style by adjusting individual parameters 
like [ Sharpness] and [ Contrast]. To see the resulting effects, take test 
shots. To customize [ Monochrome], see page 112.
1Select [Picture Style].
 Under the [ 2] tab, select [Picture 
Style ], then press < 0>.
XThe Picture Style selection screen will 
appear.
2Select a Picture Style.
  Select a Picture Style, then press the 
 button.
XThe Detail set. screen will appear.
3Select a parameter.
 Select a parameter such as 
[Sharpness], then press < 0>.
4Set the parameter.
  Press the < U> key to adjust the 
parameter as desired, then press 
< 0 >.
  Press the < M> button to save 
the adjusted parameters. The Picture 
Style selection screen will reappear.
XAny parameter settings different from 
the default will be displayed in blue.
A  Customizing Image Characteristics N
COPY